LIST PROGRAMS
MODE
The
HAAS
Control
Series
SLIDE LEGEND
PRESS
ACTIONS
KEYS
THREE TIMES
TO GET TO
THIS PAGE
INSTRUCTIONS
(Continued on
next slide)
INFORMATION
Note:
OTHER
INFORMATION
To advance through
the presentation
click
on your left mouse button
or press <ENTER>.
To exit press <ESC>.
LIST PROGRAMS
MODE
This module is
intended to provide
you with a
familiarization
of the List Programs
Mode on the Haas
Control
Here is where you find the
List Programs Buttons
List Programs
Buttons
LIST PROGRAMS:
SELECT PROGRAM:
SEND RS232:
RECEIVE RS232:
ERASE PROGRAM:
Pressing the List Program button on the
control will display a list of all of the
programs loaded in the control, up to
a maximum of 500 programs.
List Programs
Button:
List Programs Button:
Press
<LIST PROG>
This will bring up the
Programs screen and
display the programs
loaded in the control, up
to 500 maximum.
An asterisk (*) will be to
the left of the selected
program.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
List Programs
Button:
To highlight a program
for selection do one or a
combination of the
following:
Cursor Up or Down
Scroll using the Hand
Wheel.
Press
<HOME> to get to the
top of the list.
Press
<END> to get to the
bottom of the list.
To highlight and Select
a program.
Type in the program
number and Press
<WRITE/ENTER>
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Select Program
Button:
Select Program
Button:
When the program you
want is highlighted
Press
<SELECT PROG>
This will select the
program that the cursor
is on in the list of
programs.
An asterisk (*) will be to
the left of the selected
program.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Select Program
Button:
Select Program
Button:
When the program you
want is highlighted
Press
<SELECT PROG>
This will select the
program that the cursor
is on in the list of
programs.
An asterisk (*) will be to
the left of the selected
program.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Send RS232 Button:
Send RS232 Button:
Press
<SEND RS232>
This will transmit the
program or programs
out the RS232 serial
port.
It will send the program
that is highlighted.
It will send All the
programs if ALL is
highlighted.
A ‘%’ is sent at the
beginning and end of
the transmitted string.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Send RS232 Button:
Send RS232 Button:
It is also possible to
send the following via
RS232:
Parameters
Offsets
Settings
Macro Variables
Go to the display for the
one you want to
transmit and
Press
<SEND RS232>
The following Settings
effect RS232
Transmission:
Setting 11, 12, 13, 14
and 37.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Receive RS232
Button:
Receive RS232 Button:
Press
<RECV RS232>
This will receive one or
more programs from the
RS232 serial port.
Enter a valid program
number before pressing
the receive button.
If ALL is highlighted, do
not enter a program
name. The program
names will be entered
automatically.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Receive RS232
Button:
Receive RS232 Button:
It is also possible to
receive the following via
RS232:
Parameters
Offsets
Settings
Macro Variables
Go to the display for the
one you want to receive
and
Press
<RECV RS232>
The following Settings
effect RS232 Receive:
Setting 11, 12, 13, 14
and 37.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Erase Program
Button:
Erase Program Button:
Press
<ERASE PROG>
This will erase the
highlighted program, or
the program specified in
the input buffer.
If ALL is highlighted all
programs will be
erased.
PROGRAM (LIST PROG)
O91002
N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
** O00123
O00123 (Mill
(Mill HMC2)
HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
Prepared by Haas Automation
Training Department
Oxnard, CA 93030