Y1
6-Port Antenna
Frequency Range 1710–2690
X
Dual Polarization
65°
HPBW
Adjust. Electr. DT 2°–14°
Y2
Y3
1710–2690 1710–2690
X
X
65°
65°
2°–14°
2°–14°
set by
6-Port Antenna 1710–2690/1710–2690/1710–2690 65°/65°/65° 18/18/18dBi 2°–14°/2°–14°/2°–14°T
Type No.
80010727
Left system
Y1, connector 1– 2
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
MHz
dBi
dBi
1710 – 1880
17.6
17.5 ± 0.5
1850 – 1990
18.2
18.2 ± 0.3
1710 – 2690
1920 – 2180
18.3
18.2 ± 0.2
2300 – 2400
18.5
18.4 ± 0.4
2490 – 2690
18.5
18.2 ± 0.5
°
67 ± 4.3
64 ± 2.3
62 ± 2.3
59 ± 2.9
57 ± 3.3
dB
> 25
> 24
> 24
> 24
> 24
dB
> 25
> 25
> 25
> 27
> 20
dB
> 12.0
> 10.0
> 9.0
> 8.5
> 10.0
dB
< 1.0
< 1.0
< 1.0
< 1.5
< 2.0
°
7.0 ± 0.5
6.4 ± 0.3
6.1 ± 0.5
5.3 ± 0.2
4.8 ± 0.3
°
< 0.4
< 0.4
< 0.4
< 0.4
< 0.3
dB
> 17
> 20
> 20
> 18
> 19
°
2.0 – 14.0
936.4615/d ngmn 04.18.05.06 Subject to alteration.
Cross Polar Isolation
dB
> 30
Port to Port Isolation
dB
> 30 (Y1 // Y2 // Y3)
Max. Effective Power
W
250 (at 50 °C ambient temperature)
per Port
Max. Effective Power
W
500 (at 50 °C ambient temperature)
Port 1–2
Values based on NGMN-P-BASTA (version 9.6) requirements.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
80010727 Page 1 of 4
6-Port Antenna
Center system
MHz
dBi
dBi
1710 – 1880
17.3
17.2 ± 0.4
1850 – 1990
17.8
17.8 ± 0.4
1710 – 2690
1920 – 2180
18.0
17.9 ± 0.3
2300 – 2400
18.1
17.8 ± 0.5
2490 – 2690
18.0
17.9 ± 0.5
°
68 ± 7.0
62 ± 4.9
61 ± 3.4
63 ± 2.5
59 ± 3.9
dB
> 24
> 24
> 24
> 25
> 24
dB
> 26
> 28
> 30
> 29
> 24
dB
> 10.5
> 9.5
> 10.5
> 9.0
> 8.5
dB
< 1.5
< 1.0
< 1.5
< 2.0
< 2.5
°
6.9 ± 0.4
6.4 ± 0.3
6.1 ± 0.4
5.3 ± 0.2
5.0 ± 0.3
°
< 0.4
< 0.3
< 0.3
< 0.4
< 0.2
dB
> 20
> 24
> 22
> 22
> 18
°
2.0 – 14.0
Cross Polar Isolation
dB
Port to Port Isolation
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 3–4
Values based on NGMN-P-BASTA (version 9.6) requirements.
> 28
> 30 (Y1 // Y2 // Y3)
250 (at 50 °C ambient temperature)
500 (at 50 °C ambient temperature)
Right system
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
Y3, connector 5 – 6
MHz
dBi
dBi
1710 – 1880
17.6
17.6 ± 0.5
1850 – 1990
18.2
18.1 ± 0.3
1710 – 2690
1920 – 2180
18.3
18.2 ± 0.3
2300 – 2400
18.5
18.4 ± 0.5
2490 – 2690
18.6
18.3 ± 0.4
°
68 ± 3.9
65 ± 2.3
64 ± 2.8
58 ± 4.2
57 ± 2.4
dB
> 24
> 25
> 24
> 23
> 22
dB
> 24
> 24
> 25
> 25
> 21
dB
> 13.0
> 10.5
> 9.5
> 8.0
> 11.5
dB
< 1.0
< 1.0
< 1.0
< 2.0
< 2.0
°
6.9 ± 0.5
6.4 ± 0.3
6.1 ± 0.4
5.3 ± 0.2
4.8 ± 0.2
°
2.0 – 14.0
°
< 0.3
< 0.4
< 0.4
< 0.4
< 0.5
dB
> 19
> 23
> 23
> 21
> 21
Cross Polar Isolation
dB
Port to Port Isolation
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 5–6
Values based on NGMN-P-BASTA (version 9.6) requirements.
Page 2 of 4 80010727
> 30
> 30 (Y1 // Y2 // Y3)
250 (at 50 °C ambient temperature)
500 (at 50 °C ambient temperature)
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
936.4615/d ngmn 04.18.05.06 Subject to alteration.
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
Y2, connector 3 – 4
6-Port Antenna
Mechanical specifications
Electrical specifications, all systems
Impedance
Ω
50
VSWR
< 1.5
Return Loss
dB
> 14
Interband Isolation
dB
> 30
Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)
Polarization
°
+45, –45
800 (at 50 °C ambient
Max. Effective Power
W
temperature)
for the Antenna
Values based on NGMN-P-BASTA (version 9.6) requirements.
Input
Connector Position
Adjustment Mechanism
Wind load
(at Rated Wind
Speed: 150 km/h)
Max. Wind Velocity
N | lbf
km/h
mph
Height / Width / Depth mm
inches
Category of
Mounting Hardware
Weight
kg
lb
Packing Size
mm
inches
Scope of Supply
Accessories (order separately if required)
6 x 7-16 female
bottom
FlexRET,
continuously adjustable
Frontal
860 | 193
Lateral
200 | 45
Rearside
860 | 193
200
124
1475 / 378 / 103
58.1 / 14.9 / 4.1
M (Medium)
18.0 / 20.2 (clamps incl.)
39.7 / 44.5 (clamps incl.)
2000 / 549 / 120
78.7 / 21.6 / 4.7
Panel, FlexRET and
2 units of clamps
for 42 – 115 mm |
1.7– 4.5 inches diameter
2)
Type No.
Description
Remarks
mm | inches
731651
85010002
85010003
737978
86010154
86010155
1 clamp
1 clamp
1 clamp
1 downtilt kit
Site Sharing Adapter
Site Sharing Adapter
Mast diameter: 28 – 60 | 1.1 - 2.4
Mast diameter: 110 – 220 | 4.3 – 8.7
Mast diameter: 210 – 380 | 8.3 – 15.0
Downtilt angle: 0° – 15°
3-way (see figure below)
6-way (see figure below)
1)
1) 64 | 2.5
2) ’9 | 0.4
Weight
Units per
approx. kg | lb antenna
0.8 | 1.8
2.7 | 6.0
4.8 | 10.6
2.3 | 5.1
0.65 | 1.4
1.35 | 3.0
2
2
2
1
1.1 | 2.4
2
738546
86010153
1 clamp
FlexRET
Mast diameter: 42 – 115 | 1.7 – 4.5
1475 | 58.1
1496 | 58.9
1607 | 63.3
Accessories (included in the scope of supply)
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Reflector screen: Aluminum.
Fiberglass radome: The grey fiberglass radomes of these antennas are very stable and
extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to
match their surroundings.
All screws and nuts: Stainless steel.
936.4615/d ngmn 04.18.05.06 Subject to alteration.
Material:
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are
DC grounded.
Configuration example
with Site Sharing Adapter 86010154
FlexRET
FlexRET
Configuration example
with Site Sharing Adapter 86010155
FlexRET
FlexRET
FlexRET
FlexRET
All dimensions in mm | inches
Site Sharing Adapter
3-way
Site Sharing Adapter
6-way
AISG
BTS-A
AISG
BTS-B
BTS-C
BTS1
BTS2
BTS3
BTS4
BTS5
BTS6
For more information please refer to the respective data sheets.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
80010727 Page 3 of 4
6-Port Antenna
Layout of interface:
103 | 4.1
Y1(L) / Y2(C) / Y3(R) 1710–2690
120 | 4.7
220 | 8.7
320 | 12.6
378 | 14.9
Bottom view
All dimension in mm | inches
Frequency range
Array
Connector
1710 – 2690 MHz
1710 – 2690 MHz
1710 – 2690 MHz
Y1
Y2
Y3
1–2
3–4
5–6
Y1
Y2
Y3
Left Center Right
Any previous data sheet issues have now become invalid.
Page 4 of 4 80010727
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
936.4615/d ngmn 04.18.05.06 Subject to alteration.
Correlation Table
Mounting Hardware
Clamp Included in the Scope of Supply
Suitable for mast diameter
(mm)
[inches]
(mm)
[inches]
Antenna – mast distance
Material of clamp and screws
Weight
(kg)
[lb]
42 – 115
[1.65 – 4.53]
20 – 25
[0.79 – 0.98]
Hot-dip galvanized steel / stainless steel
1.1
[2.43]
100 [3.94]
40 [1.57]
40 [1.57]
72 [2.83]
20–25
[0.79–0.98]
152 [5.98]
15
2–1
’ 4 4.53]
5–
[1.6
M10 ‰MA = 25 Nm
35 [1.38]
M8 ‰MA = 20 Nm
64 [2.52]
125 [4.92]
936.3920/c
Subject to alteration.
20–25
[0.79–0.98]
Please note: Kathrein does not recommend to use counter nuts.
The additional nuts supplied are only meant as spares.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
All dimensions in mm and [inches]
738546 Page 1 of 1
FlexRET
A flexible, integrated solution for adjusting the electrical downtilt of Kathrein FlexRET antennas.
●
●
Compliant to AISG 1.1 and 3GPP/AISG 2.0
Single RETs or Multi RET displayed
Protocols
Logical interface ex factory 1)
Operates as
Ex factory
Input voltage range
V
Power consumption
W
Connectors
Hardware interfaces
Housing material
Weight
Packing size
(H x W x D)
Dimensions
(H x W x D)
●
Daisy Chain feasibility
Pre-configurated
86010153
Type No.
Adjustment time
(full range)
Adjustment cycles
Temperature range
Protection class
Lightning protection
●
sec
°C
g
lb
mm
inches
mm
inches
compliant to AISG 1.1 and 3GPP/AISG 2.0
3GPP/AISG 2.0
Single RETs or Multi RET
Single RETs
10 ... 30 (pin 1, pin 6)
< 0.5 (stand by); < 10 (motor activated)
2 x 8 pin connector according to IEC 60130-9; according to AISG
Daisy chain in: male; Daisy chain out: female
RS 485A/B (pin 5, pin 3);
power supply (pin 1, pin 6); DC return (pin 7);
according to AISG / 3GPP
40
(typically, depending on antenna type)
> 50,000
–40 … +60
IP 24 (installed)
AISG interface (each pin)
2.5 kA (10/350 µs)
8 kA (8/20 µs)
Profile: Aluminum anodized; cover: Aluminum die cast coated
350
0.77
245 x 93 x 102
9.6 x 3.6 x 4
142 x 71 x 50.4
5.6 x 2.8 x 2
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 with a vendor
specific command. Start-up operation of the FlexRET is only possible in a RET system supporting
3GPP/AISG 2.0!
1)
Please note:
If the Primary which controls the FlexRET system does not support the default ex-factory interface
setting, then the RCU must be switched to the appropriate standard of the Primary before installation.
Please contact Kathrein for further information.
936.4643/b
Subject to alteration.
If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna
after power on automatically. It is not necessary to configurate the FlexRET manually.
Standards:
EN 60950-1 (Safety)
EN 60950-22 (Safety – Equipment installed outdoor)
EN 55022 (Emission)
EN 55024 (Immunity)
ETS 300019-1-4 (Environmental)
UL 60950-1; 1st edition
Certification:
CE, FCC
Scope of supply:
FlexRET
Optional:
Site Sharing Adapter (86010154 or 86010155) to create independent logial
interfaces at one antenna or site. Makes it possible to operate with more
than one independent Node B.
Please note:
In general, the addressing of the FlexRET is automatically performed. Only in case the FlexRET is
manually addressed, the serial number has to be extended by the corresponding colour coding extension
(e.g. CSG351234-R1). The respective information can be found on the site documentation which is
included in the scope of supply.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
86010153 Page 1 of 4
FlexRET
Startup of FlexRET
The FlexRET module included in the antenna is preconfigured with the following information:
Antenna model no., Antenna Serial no., Antenna configuration data. After connecting a control
cable and scanning the antenna line devices (ALD) the used primary (e.g. NodeB, ALC, etc.)
will find the FlexRET. You only need to insert your additional data.
Connecting the control cables:
Connect a control cable to the daisy chain input of the FlexRET. The tightening torque for fixing the
connector must be 0.5 – 1.0 Nm (‘hand-tightened’).
The connector should be tightened by hand or by a special torque screw driver (order no.
85010080).
See also data sheet for Kathrein AISG-cable (86010007, ...).
Please note: To ensure the tightness of the RET System, Kathrein recommend the use of
Kathrein components only.
Please note: If the daisy chain output is not used, do not remove the protection cap.
936.4643/b
Subject to alteration.
For daisy chain operation, remove the protection cap and attach a control cable to interconnect
with the daisy chain input of the subsequent FlexRET or external RCU.
Please note: Do not remove the protection cap on the daisy chain output of the last FlexRET
or RCU device.
Page 2 of 4 86010153
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
FCC – Statements
' !!! *,/%,1
(+$"%!(,)')AE$)'*!(4%')$#((* ))$)$!!$,#),$
$#)$#(39A:(+".#$)*('"*!#)''#2#9B:)(+"*()%)#.
#)''#'+2#!*##)''#))".*(*#('$%')$#4
*,/%,+/
$)3(&*%"#)(#)()#$*#)$$"%!.,))!")($'!(()!+2
%*'(*#))$%')AE$)*!(4(!")('(#)$%'$+'($#!%'$))$#
#()'"*!#)''##'(#)!#()!!)$#4(&*%"#)#')(2*((##
')'$'&*#.#'.#2#$)#()!!#*(#$'#,))#()'*)$#(2".
*('"*!#)''#)$'$$""*#)$#(4$,+'2)'(#$*'#)))
#)''#,!!#$)$*'#%')*!'#()!!)$#4 )(&*%"#)$(*('"*!
#)''#)$'$$')!+($#'%)$#2,#)'"#.)*'##)&*%"#)$
#$#2)*('(#$*')$)'.)$$''))#)''#.$#$'"$'$)$!!$,#
"(*'(3
8$'#)$''!$))'+##)##4
8 #'()(%')$#),#)&*%"#)#'+'4
8$##))&*%"#)#)$#$*)!)$#'*)'#)'$")))$,)'+'(
$##)4
8$#(*!))!'$'#-%'#'$6)##$'!%4
& !0%,%.
(+$"%!(,) #*()'.#!#7-"%)()#'9(:4%')$#((* ))$
)$!!$,#),$$#)$#(39A:)(+".#$)*(#)''#2#9B:)(+"*()
%)#.#)''#2#!*##)''#))".*(*#('$%')$#$)+4
Subject to alteration.
&++.
936.4643/b
%'(#)%%'!()$#$'"*- = #*()'#%%!!(*-%%'!('$
-"%)(!#4 =-%!$))$#()*)$'(*-*-$#)$#((*+#)(39A:!=%%'!#
$)%(%'$*''$*!!2)9B:!=*)!()*'!=%%'!$)%)')$*)'$*!!
'$!)'&*(*2""(!'$*!!()(*(%)!=#$"%'$"))'!$#)$##"#)4
(!(()!%%')*($"%!(,)## 7@@C4
)%%'!#*"'&*!!((()$#$'"!#$'"
7@@C*#4
*,/%-,( !!!)
;#.<#($'"$)$#(#$)-%'((!.%%'$+.)%').'(%$#(!$'$"%!#$*!
+$)*('5(*)$').)$$%'))&*%"#)4
86010153 Page 3 of 4
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
FCC – Statements
Compliance Information Statement
(Declaration of Conformity Procedure)
Responsible Party:
Kathrein USA
Address:
Greenway Plaza II 2400 Lakeside Blvd. Suite 650
Richardson, Texas 75082
Telephone:
(01+) 214.238.8800
Type of equipment:
936.4643/b
Subject to alteration.
Model Name: FlexRET
FCC ID SP3-86010153
Page 4 of 4 86010153
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com