Engine Compartment Lighting KIT (E.C.L.) 1991‐1997 Toyota Land Cruiser FJ80/Lexus LX450 Thank you for purchasing the Engine Compartment Lighting Kit from yodaTEQ designs for your FJ Cruiser. All attempts have been made to supply your E.C.L. and related parts in perfect condition with complete installation hardware. However should you have any problems with the condition of the parts or find any parts missing, please do not hesitate to contact us at 714‐510‐0770 or sales@yodaTEQ.com. Your yodaTEQ Off‐Road parts are guaranteed free of defect in material and workmanship for a period of one year from date of purchase. Should you experience any problems, please contact us directly to resolve any issues. We have attempted to provide complete installation instructions provided below. However from time to time changes might be made to parts and associated hardware and you might notice small inconsistencies with the instructions. Please notify us of such occurrences so we can correct them. Step by step Install Video provided for your convenience 1 Qty 1 1 2 2 1 4 6 Part Included Engine Compartment Light (E.C.L.) Harness Inline AC Fuse Holder Cable Mounts with 3m VHB tape 7.5 amp ATC Fuses Pin Switch ‐ ground activated 6" Zip Ties ‐ Self locking nylon cable 8" Zip Ties ‐ Self locking nylon cable TOOLS & items needed for install Fish tape Rubbing Alcohol Electrical tape / Painters tape Automatic center punch Needle nose pliers Drill Gun 1/8" Drill bit 5/16" Drill bit 11mm wrench ‐ top of pin switch 12mm wrench ‐ bottom of pin switch 10 mm wrench ‐ Battery terminal Heat gun or hair dryer Engine Compartment Lighting KIT (E.C.L.) and all items included *There might be some slight variation to your vehicle's specific kit 2 Step by Step Instructions: Clean surface where LED Strip will be affixed with rubbing alcohol Run wiring through hood 1) Insert pull cord (fish tape) under hood insulation 2) Use needle nose pliers to pull cord out of the hole in insulation
3 3) Tape the ECL Wiring harness to the to the pull cord 4) Insert your nylon pry bar or other soft tool to make a larger gap to run wiring through 5) Pull ECL Wiring harness though the hole in the hood insulation 6) Clean surface where Zip Tie Mounts will be with rubbing alcohol 4 7) Attach the (2) ¾"X ¾" zip tie mounts to the two locations shown. Top & Bottom, Middle will come later (be sure to apply pressure to each mount for 5 seconds) Fasten ECL wiring harness to the mounts using the 6" zip ties (allow some slack for now) Install the ECL LED Light Strip *Clean surface where LED Strip will be affixed with rubbing alcohol *We recommend to use blue painter's tape to use as a guide for proper ECL LED Placement 5 1 ) Start on the driver's side and remove the RED 3M VHB backing and 3" at a time of the TAN 3M VHB backing ‐ For each 3" section press firmly for 5 seconds 2) Follow your blue painters tape as a guide and while pulling the Tan 3M VHB backing 3" at a time 3) Once you have reached the end of the LED strip go back and apply additional pressure to the LED strip 6 Secure ECL Wire Harness 1) Add the middle zip tie mount and remember to apply pressure to the mount for 5 seconds 2) Secure the ECL wiring harness by tightening the zip ties and cutting the excess zip tie 3) Use provided zip ties to secure ECL wiring harness to the windshield wiper fluid hose and wiring along inter fender 4) Run ECL wiring harness to the front of the truck Positive connection 1) Connect the positive wire (Male bullet connector) to the fuse holder (female bullet connector) ‐ We have provided additional heat shrink to seal the male and female connection ‐ 7 2) Move the heat shrink over the connected bullet connectors and Use a heat gun or hair dryer to activate the heat shrink to seal the connection Negitive connection & Piun Switch 1) Run the negative connection of the ECL wiring harness towards the front of the truck 2) Mark hole location: 1¾" on center from the radiator support bolt 3) Use a center punch to form a dimple to guide the drill bit 8 4) Drill a 5/16" hole for the pin switch 5) Insert star washer and nut at the bottom of the pin (securing the pin switch) Be sure to insert the star washer first 6) Tighten pin switch with a 11mm on top and 12mm below (be sure not to over tighten) 7) Connect the ground wire from the ECL wiring harness (female connector) to the pin switch (Male connector) Positive connection #2 and final steps 1) Connect the ECL wiring harness' positive ring terminal to your truck's battery's positive terminal
2) Insert fuse into inline fuse holder and "Let there be light" 9 Your install is now complete! Thanks for the purchase of the Engine Compartment Lighting Kit E.C.L. for your FJ80! 10