Model Information
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / SIZE / OPERATION / LAMP & BALLAST / INPUT
Installation Instructions
Model
BS100
Operation
HT (AC Only)
Lamps
2x17W T8
2x32W T8
2x24W T5 HO
2x28W T5
2x28W T5
2x54W T5 HO
Input
120V/277V
Other volteges available contact
factory.
Lamp Socket / Holder
Lens Clips (4 or 8 in Total)
Fixture Body
Lens / Diffuser
Reflector
Lamps
(Not Supplied)
Conduit Knockouts
(Both Ends)
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 P: 954 442 6600
F: 954 442 6677
www.BeghelliLuce.com
Illumina
BS100
Fluorescent
Important Safeguards
When using electrical equipment, basic
safety precautions should always be followed
including the following:
When installing BS100 in cold environments
Beghelli recommends the use of expansion
joints for installation (not supplied).
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Do not let power cords touch hot surfaces.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations
and at heights where unauthorized personnel
will not readily subject it to tampering.
The use of accessory equipment not
approved by Beghelli and/or any modification
or direct penetration of the fixture voids the
factory warranty.
Do not use equipment for other then it’s
intended purpose.
Servicing of this equipment should be
performed by qualified service personnel.
SAVE THESE INSTRUCTIONS
1-Remove Lens/Dif-
Installation
First make sure Power is turned off.
1. Remove lens / Diffuser.
2.Remove the reflector and mounting
hardware bag..
3. Install the weatherproof electrical connector.
(If needed)
4. Securely mount the fixture hardware
provided. The fixture can be snapped onto the
hardware as illustrated.
5. Prepare fixture for wiring / Hang Reflector
From Internal clips
6. Connect AC supply and ground as labeled
on the provided wire leads. Insulate unused
wire! CAUTION! Failure to insulate unused
wire may result in a shock hazard or unsafe
condition as well as equipment failure. Route
wires and secure them in place. IMPORTANT:
only for BS100 “SA” you must connect AC
Power before connecting Emergency Ballast.
7. Insert the lamps into the lamp holders and
twist to lock them into place.
8. Install closure clips. Reposition the lens and
snap each of the four (4) or eight (8) clips into
place (a “clack” sound is made).
9. Turn on AC voltage.
(%)*$+*,'5%*6,)&.$+%*1
4-0*1$.22'(%)*$+*,'-.&/w.&!
26 inches
51 inches
19 inches
27 inches
57-.*,'R!"!#$%&'8&%9'0*$!&*.2'52+:1
675%9:2!$!'32!#$&+#.2'5%**!#$+%*1
L
2a-Remove R!"!#$%&
N
L
L
7-0*1$.22';.9:1
Neutral / Common
BALLAST
N
3-0*1$.22'32!#$&+#.2'4+&+*,'5%**!#-
Line / Hot
L
2b-Remov!'(%)*$+*,'-.&/w.&!'
L
N
8-0*1$.22';!*1'<'=+>)1!&
'<52%1)&!'52+:1
Ground
Labeled wire leads are provided for
Line / Hot, Neutral / Common and Ground.
Labels will indicate the rated input voltage:
120VAC or 277VAC 60Hz.
Exact ballast and wiring configuration
may differ from image above:
FOLLOW ACTUAL WIRE LABELS.
8+?$)&!'Remov.2'@0>'A!#!11.&BC