Negative Battery Voltage SLIC Protection
GR-1089-CORE Intra-building Solution
Solution Products
TBU-PL060-200-WH
Objective
Compliance
The SLIC (Subscriber Line Interface
Circuit) provides all the BORSCHT
functions such as battery, ringing,
supervision between the codec and
telephone hand set. This PortNote®
solution protects negative battery
voltage solutions against surge and
power contact threats.
GR-1089-CORE intra-building, issue 5, port type 4.
• 120 Vrms, 25 A, 900 seconds withstand.
• 130 Vrms maximum AC withstand.
• Increased surge level to 5 kV, 500 A 2/10 µs.
Solution
1 TBU® High-Speed Protector:
TBU-PL060-200-WH
2 MOV Devices: MOV-10D201K
MOV-10D201K
GND
Alternate Recommendations
Other PortNote® Solutions:
• SLIC Protection - GR-1089-CORE Intra-building Solution
• Negative Battery Voltage SLIC Protection - ITU-T Solution
• Dual Supply Voltage SLIC Protection - ITU-T Solution
Benefit
This solution provides a high level of protection in
a small PCB area.
VDD
SLICTip
SLIC Line 1
Line 1
MOV-10D201K
SLIC
RJ11
TBU-PL060-200-WH
Design Kit
MOV-10D201K
SLICRing
SLIC Line 2
VSS
-VBAT
PN-DESIGNKIT-20
The schematic above illustrates the application protection and does not constitute the complete
circuit design. Customers should verify actual device performance in their specific applications.
Americas: Tel +1-951 781-5500
Fax +1-951 781-5700
Europe: Tel +41-(0)41 768 55 55 Asia-Pacific: Tel +886-2 256 241 17
Fax +41-(0)41 768 55 10 Line 2
Fax +886-2 256 241 16
COPYRIGHT© 2012 • BOURNS, INC. • 6/12 • e/CPK1130 • “PortNote” is a registered service mark of Bourns, Inc.
“Bourns” and “TBU” are registered trademarks of Bourns, Inc. in the U.S. and other countries.
Bourns® PortNote® solutions provide protection
recommendations for typical port threats.
For more information, go to:
www.bourns.com
or email: protection@bourns.com
PL
IA
NT
CO
M
*R
oH
S
L
C955401
Features
Applications
■ Superior circuit protection
■ SLIC protection
■ Overcurrent & overvoltage protection
■ Cable & DSL
■ Blocks surges up to rated limits
■ MDU/MTU modems
■ High-speed performance
■ ONT
■ Small SMT package
■ Voice/DSL line cards
■ RoHS compliant*
■ Agency recognition:
TBU-PL Series - TBU® High-Speed Protectors
General Information
Vdd
The TBU-PL Series of Bourns® TBU® products are low capacitance dual bidirectional high-speed protection
components, constructed using MOSFET semiconductor technology, and designed to protect against faults
caused by short circuits, AC power cross, induction and lightning surges.
In addition to overcurrent protection, an added feature is the voltage monitoring on the two lines. If the voltage
on the line drops below Vss then the voltage will trigger the device to switch to the blocking state.
Line 1 SLIC
Line 1
Line 2 SLIC
Line 2
The TBU® high-speed protector placed in the system circuit will monitor the current with the MOSFET detection circuit triggering to provide an effective barrier behind which sensitive electronics will not be exposed to
large voltages or currents during surge events. The TBU® device is provided in a surface mount DFN package
and meets industry standard requirements such as RoHS and Pb Free solder reflow profiles.
Agency Approval
UL
Description
File Number: E315805
Vss
TBU ® Device
Industry Standards (in Conjunction with OVP Device)
Solutions available for GR-1089-CORE, ITU-T and a combination of both.
Absolute Maximum Ratings (@ TA = 25 °C Unless Otherwise Noted)
Symbol
Parameter
Vimp
Peak impulse voltage withstand with duration less than 10 ms
Vrms
Continuous A.C. RMS voltage
Top
Tstg
Tjmax
ESD
Operating temperature range
Storage temperature range
Maximum Junction Temperature
HBM ESD Protection per IEC 61000-4-2 on line pads
Part Number
TBU-PL050-xxx-WH
TBU-PL060-xxx-WH
TBU-PL075-xxx-WH
TBU-PL085-xxx-WH
TBU-PL050-xxx-WH
TBU-PL060-xxx-WH
TBU-PL075-xxx-WH
TBU-PL085-xxx-WH
Value
500
600
750
850
300
350
400
425
-55 to +125
-65 to +150
+125
±2
Unit
V
V
°C
°C
°C
kV
Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted)
Symbol
Itrigger
Rdevice
Rmatch
tblock
IQ
Iss
Vreset
Vto
Vss
Rth(j-l)
Rth(j-l)
Rth(j-l)
Rth(j-l)
Parameter
Part Number
Current required for the device to go from
TBU-PLxxx-100-WH
operating state to protected state
TBU-PLxxx-200-WH
Series resistance of the TBU® device
Package resistance matching of the TBU® device #1 - TBU® device #2
Time taken for the device to go into current limiting
Current through the triggered TBU® device with 50 Vdc circuit voltage
Operating current with Vss = -50 V
Forward Mode
TBU-PLxxx-100-WH
®
Reverse Mode
Voltage below which the triggered TBU
device will transition to normal operating state
Forward Mode
TBU-PLxxx-200-WH
Reverse Mode
Voltage threshold offset with 60 Hz applied voltage, with Vss -50 V (Vss - VlineSLIC)
Operating voltage range relative to Vdd
One side junction to package pads - FR4 using minimum recommended pad layout
Both sides junction to package pads - FR4 using minimum recommended pad layout
One side junction to package pads - FR4 using heat sink on board (6 cm2) (0.5 in.2)
Both sides junction to package pads - FR4 using heat sink on board (6 cm2) (0.5 in.2)
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Min.
100
200
40
Typ.
150
300
50
±0.5
0.25
0.70
100
15
13
20
17
12
10
15
12
-1.0
-180
110
65
70
40
Max.
200
400
55
±1.0
1
1.50
22
20
25
22
0.2
-20
Unit
mA
Ω
Ω
µs
mA
µA
V
V
V
°C/W
°C/W
°C/W
°C/W
TBU-PL Series - TBU® High-Speed Protectors
Functional Block Diagram
HIGH
VOLTAGE
SWITCH
Line 1 SLIC
Line 1
CURRENT
SENSE
Vdd
+
VOLTAGE
COMPARATOR
Vss
Vdd
Vss
Vdd
VOLTAGE
COMPARATOR
+
Vss
CURRENT
SENSE
HIGH
VOLTAGE
SWITCH
Line 2 SLIC
Reference Application
Line 2
Basic TBU Operation
The TBU-PL Series are high-speed protectors used in voice/
VoIP SLIC applications.The maximum voltage rating of the TBU®
device should never be exceeded. Where necessary, an OVP
device should be employed to limit the maximum voltage. A costeffective protection solution combines Bourns® TBU® protection
devices with a pair of Bourns® MOVs. For bandwidth sensitive
applications, a Bourns® GDT may be substituted for the MOV. If
EN55024 EMC compliance is required, the TBU® device
may require capacitors to be fitted between the Tip and Ring
connections and ground.
The TBU® device, constructed using MOSFET semiconductor
technology, placed in the system circuit will monitor the
current with the MOSFET detection circuit triggering to provide
an effective barrier behind which sensitive electronics are not
exposed to large voltages or currents during surge events. The
TBU® device operates in approximately 1 µs - once line current
exceeds the TBU® device’s trigger current Itrigger. When
operated, the TBU® device restricts line current to less than
1 mA typically. When operated, the TBU® device will block all
voltages including the surge up to rated limits.
GND
When the voltage on the SLIC output is driven below
(Vbat – Vto) the TBU-PL series device switches to the
blocking state, regardless of output current in the device.
2
Vdd
Line 1
SLIC
4
Line 1
1
MOV
C1
MOV
C2
After the surge, the TBU® device resets when the voltage
across the TBU® device falls to the Vreset level. The TBU®
device will automatically reset on lines which have no DC bias
or have DC bias below Vreset (such as unpowered signal lines).
TBU®
Device
Line 2
SLIC
Vss
-VBAT
Line 2
5
8
6
If the line has a normal DC bias above Vreset, the voltage
across the TBU® device may not fall below Vreset after the
surge. In such cases, special care needs to be taken to ensure
that the TBU® device will reset, with software monitoring as one
method used to accomplish this. Bourns application
engineers can provide further assistance.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
TBU-PL Series - TBU® High-Speed Protectors
Bourns® TBU® Device Solutions
Industry Standard
Telcordia GR-1089-CORE
Intra-building
Port Type 4
Telcordia GR-1089-CORE
Intra-building
Port Type 4a
Non-GR-1089-CORE Intra-building
Specifications
ITU-T Basic K.20, K.21, K.45
ITU-T Enhanced K.20, K.21, K.45
Surge & AC Withstand
TBU® Device P/N
1500 V, 100 A 2/10 µs
120 Vrms, 25 A, 900 s
TBU-PL050-100-WH
1
MOV-07D201K
2
1000 V, 100 A 10/1000 µs
120 Vrms, 25 A, 900 s
TBU-PL060-100-WH
1
MOV-10D201K
2
TBU-PL085-100-WH
1
MOV-10D361K
2
TBU-PL085-100-WH
1
MOV-10D431K
2
TBU-PL075-100-WH
1
MOV-10D361K
2
TBU-PL060-100-WH
1
TISP4400M3BJ
2
TBU-PL085-100-WH
1
MOV-10D391K
2
TBU-PL060-100-WH
1
TISP4500H3BJ
2
5000 V, 500 A 2/10 µs
230 Vrms, 25 A, 900 s
1500 V, 100 A 2/10 µs
275 Vrms, 25 A, 900 s
4000 V, 40 Ω 10/700 µs
230 Vrms 10 Ω - 1000 Ω, 900 s
600 Vrms 600 Ω, 0.2 s
4000 V, 40 Ω 10/700 µs
230 V rms 10 Ω -1000 Ω, 900 s
600 V rms 600 Ω, 0.1 s
6000 V, 40 Ω 10/700 µs
240 Vrms 10 Ω - 1000 Ω, 900 s
600 Vrms 600 Ω, 0.2 s
600 Vrms 600 Ω, 1 s*
1500 Vrms, 200 Ω, 2 s*
6000 V, 40 Ω 10/700 µs
240 Vrms 10 Ω - 1000 Ω, 900 s
600 Vrms 600 Ω, 1 s
1500 Vrms, 200 Ω, 2 s
Qty.
OVP Device P/N
Qty.
* GDT Special Test Protector with DC breakdown (DCBD) of less than 330 V.
Notes:
1) The Le9500, Le9520 and Le9530 (VE950 series) require a 200 mA Itrigger TBU® device for normal operation. Other SLIC types should use
the 100 mA device.
2) The MOV maximum continuous rms voltage rating should not be exceeded. The exception is where the data sheet highlights withstand
capability such as the 600 Vrms, 1 A for 0.2 s, for example.
3) If EN55024 EMC compliance is required, the TBU® device may require capacitors to be fitted between the Tip and Ring connections and
ground (i.e. in parallel with the MOV device). The capacitance value can be chosen to meet levels as follows:
• 10 nF for EN55024 Level 1
• 20 nF for EN55024 Level 2
• 47 nF for EN55024 Level 3
Selection of capacitor voltage rating depends upon TBU® part number selection. Recommendations include:
• TBU-PL050 & TBU-PL060 Series: 120 VAC, 500 V Peak Surge Rated
• TBU-PL075 & TBU-PL085 Series: 240 VAC, 750 V Peak Surge Rated
Depending upon the SLIC type, it is usually possible to remove any EMI capacitors present between the output of the SLIC and ground
when using capacitors C1 and C2 in parallel with the MOVs.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
TBU-PL Series - TBU® High-Speed Protectors
Performance Graphs
Typical Trigger Current vs. Temperature
Typical V-I Characteristics (TBU-PL085-200-WH)
1.8
1.6
ITRIGGER
Normalized Trigger Current
CURRENT
(50 mA/div)
VRESET
VOLTAGE
(5 V/div)
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-75 -50 -25
0
25
50
75 100 125
Junction Temperature (°C)
Typical Resistance vs. Temperature
Tracking Voltage Characteristics
2.2
Vbat range of -25 V to -150 V
2.0
100
1.8
Normalized Resistance
Resistance ( )
90
80
70
60
50
40
-4
-3
-2
-1
0
1
2
3
4
Voltage threshold offset (V)
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-75 -50 -25
0
25
50
75 100 125
Junction Temperature (°C)
Typical Surge Response
Power Derating Curve
3.0
Total Max. Power (W)
Voltage: 100 V/div
One Side, No PCB Cu
One Side, 0.5 sq. in. PCB Cu
Two Sides, No PCB Cu
Two Sides, 0.5 sq. in. PCB Cu
2.5
2.0
Time: 250 ns/div
1.5
Current: 100 mA/div
1.0
0.5
0.0
20
40
60
80
100
Ambient Temperature (°C)
120
140
(TBU-PL050-100-WH with MOV-07D201K
Using 1800 V 1.2/50 ms Surge Pulse)
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
TBU-PL Series - TBU® High-Speed Protectors
Product Dimensions
0.70
(.028)
0.725
(.029)
0.825
(.032)
0.40
(.016)
0.825
(.032)
0.85 ± 0.05
(.033 ± .002)
6.50
(.256)
1.335
(.053)
0.30
(.012)
1.15
(.045)
1.275
(.050)
0.30
(.012)
1.35
(.053)
1.20
(.047)
4.00
(.157)
0.85
(.033)
0.85
(.033)
0.73
(.029)
1.35
(.053)
1.275
(.050)
1.20
(.047)
0.85
(.033)
0.85
(.033)
PIN 1 & BACKSIDE CHAMFER
0.90
(.035)
0.85
(.033)
0.85
(.033)
1.335
(.053)
0.80 - 0.95
(.031 - .037)
1.275
(.050)
0.25
C
PIN 1
(.010)
1.25
(.049)
0.75
(.030)
1.30
(.051)
0.70
(.028)
0.00 - 0.05
(.000 - .002)
DIMENSIONS:
0.75
(.030)
0.40
(.016)
MM
(INCHES)
0.75
(.030)
Recommended Pad Layout
TBU® High-Speed Protectors have a 100 % matte-tin termination
finish. For improved thermal dissipation, the recommended layout
uses PCB copper areas which extend beyond the exposed solder
pad. The exposed solder pads should be defined by a solder mask
which matches the pad layout of the TBU® device in size and spacing. It is recommended that they should be the same dimension as
the TBU® pads but if smaller solder pads are used, they should be
centered on the TBU® package terminal pads and not more than
0.10-0.12 mm (0.004-0.005 in.) smaller in overall width or length.
Solder pad areas should not be larger than the TBU® pad sizes
to ensure adequate clearance is maintained. The recommended
stencil thickness is 0.10-0.12 mm (0.004-0.005 in.) with a stencil
opening size 0.025 mm (0.0010 in.) less than the solder pad
size. Extended copper areas beyond the solder pad significantly
improve the junction to ambient thermal resistance, resulting in
operation at lower junction temperatures with a corresponding
benefit of reliability. All pads should soldered to the PCB, including pads marked as NC or NU but no electrical connection should
be made to these pads. For minimum parasitic capacitance, it is
recommended that signal, ground or power signals are not routed
beneath any pad.
Thermal Resistance vs Additional PCB Cu Area
4
3
2
1
5
6
7
8
Dark grey areas show added PCB copper area for better
thermal resistance.
Thermal Resistance (°C/W)
120
Power in One Side of TBU® Device
Total Power in Both Sides of TBU® Device
100
80
60
40
20
0
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
Added Cu Area (Sq. In.)
1.6
1.8
2.0
®
3312Series
- 2 mm
SMD
Trimming Potentiometer
TBU-PL
- TBU
High-Speed
Protectors
Reflow Profile
Profile Feature
Average Ramp-Up Rate (Tsmax to Tp)
Preheat
- Temperature Min. (Tsmin)
- Temperature Max. (Tsmax)
- Time (tsmin to tsmax)
Time maintained above:
- Temperature (TL)
- Time (tL)
Peak/Classification Temperature (Tp)
Time within 5 °C of Actual Peak Temp. (tp)
Ramp-Down Rate
Time 25 °C to Peak Temperature
Pb-Free Assembly
3 °C/sec. max.
150 °C
200 °C
60-180 sec.
217 °C
60-150 sec.
260 °C
20-40 sec.
6 °C/sec. max.
8 min. max.
How to Order
Typical Part Marking
TBU - PL 085 - 100 - WH
MANUFACTURER’S
TRADEMARK
TBU® Product
PRODUCT CODE
- 1ST DIGIT INDICATES PRODUCT FAMILY:
L = TBU-PL SERIES
- 2ND & 3RD DIGITS INDICATE IMPULSE VOLTAGE:
50 = 500 V
60 = 600 V
75 = 750 V
85 = 850 V
Series
PL = Dual Bidirectional Series
- 4TH DIGIT INDICATES TRIGGER CURRENT:
1 = 100 mA 2 = 200 mA
Impulse Voltage Rating
050 = 500 V
060 = 600 V
075 = 750 V
085 = 850 V
PIN 1
MANUFACTURING
DATE CODE
- 1ST DIGIT INDICATES THE YEAR’S 6-MONTH PERIOD.
- 2ND DIGIT INDICATES THE WEEK NUMBER IN THE 6-MONTH PERIOD.
- 3RD & 4TH DIGITS INDICATE SPECIFIC LOT FOR THE WEEK.
Trigger Current
100 = 100 mA
200 = 200 mA
Hold to Trip Ratio Suffix
W = Hold to Trip Ratio
6-MONTH PERIOD CODES:
A = JAN-JUN 2009
C = JAN-JUN 2010
B = JUL-DEC 2009
D = JUL-DEC 2010
Package Suffix
H = DFN Package
E = JAN-JUN 2011
F = JUL-DEC 2011
Device Pin Out
Pad Designation
2
Pin Out
Pad #
1
Line 1
5
Line 2 SLIC
2
6
Vss (SLIC Negative Supply or -Vbat)
3
Vdd (SLIC Ground or 0 V)
Not Used
7
Not Used
4
Line 1 SLIC
8
Line 2
Pad #
4
1
5
8
Pin Out
6
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
3312 - Series
2 mm SMD
Potentiometer
TBU-PL
- TBU®Trimming
High-Speed
Protectors
Packaging Specifications
P0
E
D
t
B
P2
TOP
COVER
TAPE
A
N
F
W
C
D
B0
K0
CENTER
LINES OF
CAVITY
A0
P
D1
EMBOSSMENT
G (MEASURED AT HUB)
USER DIRECTION OF FEED
QUANTITY: 3000 PIECES PER REEL
A
Min.
326
(12.835)
B
Max.
330
(13.002)
Min.
1.5
(.059)
A0
Min.
4.30
(.169)
B0
Max.
4.50
(.177)
Min.
6.70
(.264)
K0
Min.
1.0
(.039)
C
Max.
2.5
(.098)
Min.
7.9
(.311)
D
Max.
13.5
(.531)
D
Max.
6.90
(.272)
Min.
1.5
(.059)
P
Max.
1.2
(.047)
Min.
12.8
(.504)
Min.
1.5
(.059)
Min.
3.9
(.159)
E
Max.
-
Min.
1.65
(.065)
P2
Max.
4.1
(.161)
Min.
1.9
(.075)
G
Ref.
16.5
(.650)
Max.
D1
Max.
1.6
(.063)
P0
Max.
8.1
(.319)
Min.
20.2
(.795)
F
Max.
1.85
(.073)
Min.
7.4
(.291)
Max.
0.35
(.014)
Min.
15.7
(.618)
t
Max.
2.1
(.083)
Min.
0.25
(.010)
N
Ref.
102
(4.016)
max.
7.6
(.299)
W
DIMENSIONS:
Asia-Pacific: Tel: +886-2 2562-4117 • Fax: +886-2 2562-4116
Europe: Tel: +41-41 768 5555 • Fax: +41-41 768 5510
The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700
www.bourns.com
REV. 01/25/12
“TBU” is a registered trademark of Bourns, Inc. in the United States and other countries.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Max.
16.3
(.642)
MM
(INCHES)
T
PL
IA
N
OM
C
01K
5
Applications
n High voltage rating
n Power supplies
n High current rating
n Power systems
n Bidirectional
n Line voltage
n Surge protection
n Telecom systems
n Fast response time
n White goods / appliances
n RoHS compliant*
F
RE
E
*R
oH
S
10D2
Features
LE
AD
n Agency listing:
MOV-10DxxxK Series - Metal Oxide Varistor
General Information
Industry Standard Compliance
Ro VE LEA
HS RS D
C ION FRE
OM S E
PL AR IA E
NT
*
The MOV-10DxxxK Series of 10 mm radial leaded varistor devices protects
against overvoltage transients such as lightning, power contact and power
induction. The metal oxide varistors offer a choice of varistor voltages from
18 V to 820 V and Vrms voltages from 11 V to 510 V.
The devices have a high current handling, high energy absorption capability
and fast response times to protect against transient faults up to rated limits.
Standard
File Number
UL 1449
E313168
Standard
MOV-10D201K
MOV-10D361K
MOV-10D391K
MOV-10D431K
ITU-T K.20, K.21, K.45
Will pass 600 V rms,
600 ohm, 1 A, 0.2 s, 5
cycles, every 1 minute
condition.
Absolute Maximum Ratings (@ TA = 25 °C Unless Otherwise Noted)
Parameter
Operating Temperature
Storage Temperature
Rated Wattage
Varistor Voltage Temperature Coefficient
Response Time
Varistor Voltage Tolerance
Symbol
TOPR
TSTG
Pw
VTC
Tr
Vtol
Min.
-40
-40
Typ.
25
25
0
10
-10
Max.
+85
+125
0.40
0.05
25
10
Unit
˚C
˚C
Watt
% / ˚C
ns
%
Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted)
Bourns Part No.
MOV-10D180K
MOV-10D220K
MOV-10D270K
MOV-10D330K
MOV-10D390K
MOV-10D470K
MOV-10D560K
MOV-10D680K
MOV-10D820K
MOV-10D101K
MOV-10D121K
MOV-10D151K
MOV-10D181K
MOV-10D201K
MOV-10D221K
MOV-10D241K
MOV-10D271K
MOV-10D301K
MOV-10D331K
MOV-10D361K
MOV-10D391K
MOV-10D431K
MOV-10D471K
MOV-10D511K
MOV-10D561K
MOV-10D621K
MOV-10D681K
MOV-10D751K
MOV-10D781K
MOV-10D821K
Max. Continuous
Voltage (V)
Voltage @ 1 mA DC (V)
r.m.s.
d.c.
Min.
Nom.
Max.
11
14
17
20
25
30
35
40
50
60
75
95
115
130
140
150
175
190
210
230
250
275
300
320
350
385
420
460
480
510
14
18
18
26
31
38
45
56
65
85
100
125
150
170
180
200
225
250
275
300
320
350
385
415
460
505
560
620
640
675
16
20
24
30
35
42
50
61
74
90
108
135
162
185
198
216
243
270
297
324
351
387
423
459
504
558
612
675
702
738
18
22
27
33
39
47
56
68
82
100
120
150
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
780
820
20
24
30
36
43
52
62
75
90
110
132
165
198
225
242
264
297
330
363
396
429
473
517
561
616
682
748
825
858
902
Voltage @ Class Current
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
(8/20 μs)
Max.
Class
Clamping
Current
Voltage (V)
(A)
5
36
5
43
5
53
5
65
5
77
5
93
5
110
5
135
25
135
25
165
25
200
25
250
25
300
25
340
25
360
25
395
25
455
25
500
25
550
25
595
25
650
25
710
25
775
25
845
25
925
25
1025
25
1120
25
1240
25
1290
25
1355
Max. Peak
Current
(8/20 μs)
Max.
Energy
(J)
One
Time
8/20 μs
1 kHz
500
500
500
500
500
500
500
500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2.1
2.5
3.0
4.0
4.6
5.5
7.0
8.2
12
15
18
22
27
30
32
35
40
40
43
47
60
65
70
70
70
70
70
75
80
85
5600
4250
3700
3000
2400
2100
1800
1500
1200
1000
830
670
560
500
450
420
370
330
300
280
260
230
210
200
180
160
150
130
130
110
Max. Cap.
(pF)
3312 - 2 mm
SMD- Trimming
Potentiometer
MOV-10DxxxK
Series
Metal Oxide
Varistor
Product Dimensions
Typical Part Marking
This is an RoHS compliant molded radial package with 100 % Sn plating
on the terminations.
12.5
MAX.
(.492)
10D201K
T
15.5
(.610)
MAX.
5
20.0
(.787)
MIN.
0.8 ± 0.1
(.031 ± .004)
7.5 ± 0.8
(.295 ± .031)
Bourns Part
Number
MOV-10D180K
MOV-10D220K
MOV-10D270K
MOV-10D330K
MOV-10D390K
MOV-10D470K
MOV-10D560K
MOV-10D680K
MOV-10D820K
MOV-10D101K
MOV-10D121K
MOV-10D151K
MOV-10D181K
MOV-10D201K
MOV-10D221K
Dim. T
(Max.)
3.8
(.150)
3.9
(.154)
4.2
(.165)
3.8
(.150)
4.0
(.157)
4.2
(.165)
4.3
(.169)
4.4
(.173)
3.8
(.150)
4.0
(.157)
4.2
(.165)
4.4
(.173)
3.6
(.142)
3.8
(.150)
3.9
(.154)
DIMENSIONS:
Bourns Part
Number
MOV-10D241K
MOV-10D271K
MOV-10D301K
MOV-10D331K
MOV-10D361K
MOV-10D391K
MOV-10D431K
MOV-10D471K
MOV-10D511K
MOV-10D561K
MOV-10D621K
MOV-10D681K
MOV-10D751K
MOV-10D781K
MOV-10D821K
MM
(INCHES)
Dim. T
(Max.)
4.0
(.157)
4.2
(.165)
4.4
(.173)
4.6
(.181)
4.8
(.189)
5.0
(.197)
5.2
(.205)
5.4
(.213)
5.5
(.217)
5.9
(.232)
6.2
(.244)
6.4
(.252)
6.6
(.260)
6.8
(.268)
7.2
(.283)
Bourns Part Number
MOV-10D180K
MOV-10D220K
MOV-10D270K
MOV-10D330K
MOV-10D390K
MOV-10D470K
MOV-10D560K
MOV-10D680K
MOV-10D820K
MOV-10D101K
MOV-10D121K
MOV-10D151K
MOV-10D181K
MOV-10D201K
MOV-10D221K
MOV-10D241K
MOV-10D271K
MOV-10D301K
MOV-10D331K
MOV-10D361K
MOV-10D391K
MOV-10D431K
MOV-10D471K
MOV-10D511K
MOV-10D561K
MOV-10D621K
MOV-10D681K
MOV-10D751K
MOV-10D781K
MOV-10D821K
Bourns Part Marking
10D180K
10D220K
10D270K
10D330K
10D390K
10D470K
10D560K
10D680K
10D820K
10D101K
10D121K
10D151K
10D181K
10D201K
10D221K
10D241K
10D271K
10D301K
10D331K
10D361K
10D391K
10D431K
10D471K
10D511K
10D561K
10D621K
10D681K
10D751K
10D781K
10D821K
NOTE: The “5” marking on MOV products is for traceability of production
assembly for quality assurance compliance.
How to Order
MOV - 10D nn (n) K (TR)
Model Designator
MOV = Metal Oxide Varistor
Disc Diameter
10D = 10 mm
Nominal Varistor Voltage
See Electrical Characteristics Table
Multiplier of Voltage Digits
0 = No multiplier
1 = nn * 101
Varistor Voltage Tolerance
K = 10 %
Packaging
Blank = Bulk
TR = Tape & Reel
Examples: MOV-10D270K = 27 V, Bulk Pack
MOV-10D331KTR = 330 V, Tape & Reel
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
3312 - 2 mm SMD
Trimming
Potentiometer
MOV-10DxxxK
Series
- Metal Oxide
Varistor
Performance Graphs
Maximum Clamping Voltage (V)
10000
821K
781K
751K
681K
621K
561K
511K
471K
431K
391K
361K
331K
301K
271K
241K
221K
201K
181K
151K
121K
101K
820K
1000
680K
560K
470K
390K
330K
270K
220K
180K
100
10
0.001
0.01
0.1
1
10
Current (A)
Internal Construction
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
100
1000
10000
CDDFN5-0504N
- TVS/Steering
DiodeVaristor
Array
MOV-10DxxxK Series
- Metal Oxide
Packaging Information
TAPE & REEL
Item
P2
P
Δh
Symbol
Reel Outside Diameter
RD
Reel Inner Diameter
RD1
Tape Width
RW
Reel Width
RW1
Pitch of Component
H1
Feed Hole Pitch
W2
H
W0
W1
P1
D0
L
W
F
P0
t
RD1
RD
DIMENSIONS:
RW
MM
(INCHES)
RW1
t
P
RD1
RD
P0
Feed Hole Center to Pitch
P1
Feed Hole Center to Component
Center
P2
Lead to Lead Distance
F
Component Alignment
Dh
Tape Width
W
Hole Down Tape Width
W0
Hole Position
W1
Hole Down Tape Position
W2
Height From Center to
Component Base
H
Seating Plane Height
H0
Component Height
H1
Crimp Length
C
Feed Hole Diameter
D0
Total Tape Thickness
t
Length of Clippped Height
L
Quantity per Reel
(10D180K – 10D391K)
Quantity per Reel
(10D431K – 10D821K)
10 mm Disc
355
(13.98)
30
(1.181)
55
(2.16)
63
max.
(2.48) max
25.4 ± 0.7
(1.00 ± 0.03)
12.7 ± 1.0
(0.50 ± 0.04)
8.95 ± 0.7
(0.352 ± 0.03)
12.7 ± 1.0
(0.50 ± 0.04)
7.50 ± 0.8
(0.30 ± 0.03)
2.0
RW
(0.079)
RW1 18.0 ± 0.5
(0.71 ± 0.02)
12.0 ± 0.8
(0.47 ± 0.03)
9.0 ± 0.5
(0.35 ± 0.02)
3.0
max.
(0.12) max.
19.0 ± 1.0
(0.75 ± 0.04)
16.0 ± 1.0
(0.63 ± 0.04)
36.0
max.
(1.42) max
2.60
typ.
(0.10) max
4.0 ± 0.2
(0.16 ± 0.08)
0.6 ± 0.3
(0.02 ± 0.01)
1.0
max.
(0.04) max
-
1000
-
500
BULK
250.0
(9.84)
REV. 10/12
170.0
(6.69)
60.0
(2.36)
QUANTITY = 1000 PCS. PER BOX
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Asia-Pacific:
Tel: +886-2 2562-4117
Fax: +886-2 2562-4116
Europe:
Tel: +41-41 768 5555
Fax: +41-41 768 5510
The Americas:
Tel: +1-951 781-5500
Fax: +1-951 781-5700
www.bourns.com