CUSTOMER:
REFERENCE:
OPERATING ROOM
CONSOLE CABINETS
PRODUCT SPECIFICATION
PRODUCT
Getinge Operating Room Consoles shall be made up of
individual cabinets arranged in a series to meet the needs of
particular operating rooms for storage of sterile equipment and
supplies. Each cabinet shall be constructed of 18 gauge, type
304 stainless steel with No. 4 finish. All facing joints are
welded, ground and polished to a flush, uniform satin finish. All
doors and drawers shall fit flush to the front. Available in
freestanding or recessed configurations.
QUALITY STATEMENT
Confidence in the Getinge Group is the most important quality
criterion. This must be the hallmark of all our external and
internal commitments, activities and products. Products and
services supplied by Getinge must conform to the agreed
terms and expectations to ensure recommendations for further
business. The achievement of these quality goals is the basis
for a continued competitive and successful enterprise.
SURGICAL SUPPLY CABINET
Cabinet shall be enclosed by double-pan glazed doors hung
on three semi-concealed stainless-steel hinges. One piece
outer and inner door frames hold 7/32'' (5.5mm) thick safety
plate glass. Door is equipped with pull handle and top and
bottom spring loaded nylon roller catches. Cabinet shall be
furnished with one fixed bottom shelf and three solid 18 gauge
stainless-steel shelves adjustable on 1/2'' (12.7mm) centers
for storage of equipment and supplies.
Available in three widths: 24'' (610mm), 36'' (914mm) or 48''
(1219mm) x 60'' (1524mm) high x 18'' (457mm) deep.
NOTE: 24'' wide cabinet is equipped with one door only,
hinged left or right.
Model ORSC-36
Surgical Supply Cabinet*
*Surgical supplies and accessories not included.
SURGICAL TABLE ACCESSORY CABINET
DESK CABINET
Cabinet shall consist of an open shell upper section and a
lower drawer section. The upper section includes a sloped
stainless-steel writing surface; a magnetic stainless-steel back
panel to serve as a bulletin board; and a ceiling-mounted
fluorescent light fixture. Light fixture shall be UL listed. The
lower section shall contain four stainless-steel drawers with
handles, mounted on two-section drawer slides with nylon
roller bearings and built-in extension stops. Drawer fronts shall
be double-pan construction with welded, ground and polished
corners. Cabinet shall be 24'' (610mm) wide x 60'' (1524mm)
high x 18'' (457mm) deep.
Cabinet shall be furnished with two solid, double-pan, sounddeadened doors, hung on three semi-concealed stainlesssteel hinges. Doors are equipped with pull handle, and top and
bottom spring loaded nylon roller catches. Interior back and
sides shall be provided with perforated 18 gauge stainlesssteel peg-board for standard hooks and storage of table
accessories. Available in 36'' (914mm) or 48'' (1219mm) width
x 60'' (1524mm) high x 18'' (457mm) deep.
Model ORAC-48
Surgical Table Accessory Cabinet*
Model ORDC-24
Desk Cabinet
*Surgical supplies and accessories not included.
Page 3 of 12
End Panels: 18 gauge polished stainless-steel end panels
finish off either a left or right exposed end or both ends of a
freestanding cabinet or console set of cabinets.
Shelves: Additional 18 gauge, polished stainless-steel shelves
and support brackets for the surgical supply cabinets.
Model ORAC-36
Recess Mounted
36'' Sloping Top
36'' Sub-base
DESK CABINET
Model ORDC-24
Recess Mounted
24'' Sloping Top
24'' Sub-base
CONSOLE CABINET REQUIREMENTS
SURGICAL SUPPLY CABINET
Model ORSC-48
Recess Mounted
48'' Sloping Top
48'' Sub-base
Model ORSC-36
Recess Mounted
36'' Sloping Top
36'' Sub-base
Model ORSC-24
L.H. Hinged Door
R.H. Hinged Door
Recess Mounted
24'' Sloping Top
24'' Sub-base
FINISHED END PANELS
L.H. End Panel
R.H. End Panel
ADDITIONAL SHELVES
24'' Width
36'' Width
48'' Width
WARRANTIES AND SERVICE
These Operating Room Console Cabinets
serviced without cost to owner for one
installation. Such service will include labor
material required to replace defective
workmanship.
will be factory
year following
and necessary
material and
DSORCAB 0607
All parts are warranted for a period of one year against factory
defects and will be replaced upon return of defective material.
The labor cost of such replacement after the one-year
warranty is at the owner’s expense.
Getinge is constantly reviewing its products for improvements. Consequently, the actual products may differ slightly from the products pictured and described here.
Sub-base: 12'' (305mm) high. 14 gauge polished stainless
steel base is 15'' (381mm) deep, allowing a 3'' (76mm) toe
space the full width of a freestanding cabinet.
Model ORAC-48
Recess Mounted
48'' Sloping Top
48'' Sub-base
Printed in U.S.A.
Sloping Dust Top: 8'' (203mm) high. 20 gauge polished
stainless-steel top slopes from back to front to cover full width
of cabinet for freestanding installation.
TABLE ACCESSORY CABINET
ARJO, GETINGE and MAQUET are registered trademarks.
OPTIONAL ACCESSORIES
Getinge USA, Inc.
1777 East Henrietta Road
Rochester, New York 14623-3133
U.S.A.
Phone: (800) 475-9040
Fax:
(585) 272-5033
info@getingeusa.com www.getingeusa.com
THE GETINGE GROUP is a leading global provider of equipment and
systems that contribute to quality enhancement and cost efficiency within
healthcare and life sciences. Equipment, services and technologies are
supplied under the brands ARJO for patient hygiene, patient handling and
wound care, GETINGE for infection control and prevention within healthcare
and life science and MAQUET for surgical workplaces, cardiopulmonary
and critical care.