SCHEDULE OF WORK
Name of work:- Design,Engineering,Manufacturing,Testing,Supply, installation,Erection & commissioning of 2 X 3.15 MVA, 33
Substation complete with construction of Double storied control room cum office building,equipment foundation, boundary wall
developement at Jampaijala including Construction of approximately 7.0 CKM. 33 KV "Takarjala-Jampuijala" subTransmission
Takarjala 33 KV Sub-Station.
SCHEDULE - A (Supply , installation & commissioning of Sub-station equipment, control gear and structures)
(Amount in Rs.)
Sl
No.
Description of item
1
2
1. Supply, erection, testing & commissioning of 3.15
MVA, 33 / 11 KV Delta Star, copper wound, oil
immersed, ONAN cooled outdoor type, 3Phase,
50Hz, step down power transformer with OFF load
tap changer with taps ranging from +10% to -10%
in steps of 2.5% each on HV winding with first filling
of EHV grade insulating oil & complete with
conservator tank, Buchholz relay, breather, winding
& oil temperature meters housed in outdoor panel
attached with the transformer complete as per
relevant ISS..
Quantity
3
Unit
4
2
Supply
Rate
5
Amount
6
Quantity
7
Unit
8
No.
2
No.
1
No.
1
No.
2
No.
2
No.
2. Supply, erection, testing & commissioning of 33 KV,
1000A, 750 MVA rupturing capacity, outdoor
Vacuum Circuit Breaker complete with motor
operated spring closing (Local / Remote)
arrangement with all accessories including lattice
support structure,foundation bolts,G.I. nuts &
bolts,washers etc. as required and as per relevant
ISS complete operative on 110V DC.
a) 33 KV outgoing for Takajala/Incoming at
Jampuijala
b) For Power Transformer
Page 221
Erection
Rate
9
Inspection
Amount
10
Rate
Amount
11
12
3. Supply, erection, testing & commissioning of 33 KV,
800A, manually operated horizontal rotating type
double break, triple pole Gang operated isolator
complete with post insulator, arching horns,
mechanical interlocking arrangement etc.as per
relevant ISS.
a) With earth switch.
b) Without earth switch.
4. Supply, erection, testing & commissioning of 33 KV
Single Phase, outdoor type 3 Core C.T of ratio
100 / 1-1-1 Amp with suitable burden & class of
accuracy complete with associated terminal box
connecting link etc. as per relevant ISS and as
required(For Transformer).
5
6
7
Supply, erection, testing & commissioning of 33 KV
Single Phase, outdoor type 2 Core C.T of ratio
200 / 1-1 Amp with suitable burden & class of
accuracy complete with associated terminal box
connecting link etc. ( for 33 KV incoming feeder)
Supply, erection, testing & commissioning of 33 KV
Single Phase , outdoor type P.T of ratio 33000V /
√ 3 / 110V / √ 3 having suitable burden & class of
accuracy as detailed herein after in technical
specification and as per relevant ISS .
Supply, erection, testing & commissioning of 10KA, 30
KV, Station Valve type metal oxide heavy duty
Lightning Surge Arrestor suitable for operation on
33KV Sytem conforming to ISI : 3070 (P-1) / 1974 and
amendments thereafter and as required.
2
6
No.
No.
2
6
No.
No.
6
No.
6
No.
3
No.
3
No.
3
No.
3
No.
12
No.
12
No.
Page 222
8
Supply, erection, testing & commissioning of 33 KV
control & relay panel, simplex type complete with
differential relay, 2-over current and 1- Earth fault
combined relay, Auxiliary relay, 1- voltmeter, 3ammeter, CT operated static trivector meter, internal
panel wiring, simaphore for Vacuum Circuit breaker &
isolator, Mimic bus diagram (Metal size 4mm thick X
10mm width).
a) For 3.15 MVA, 33 / 11 KV Power transformers.
b) For 33 KV outgoing/incoming feeder without
differential relay.
9
Supply , erection, testing & commisioning of 11 KV
vaccum Circuit breaker with Control & relay panel
(Incoming) simplex type 800 A contineous current
rating,, 350 MVA rupturing capacity complete with
manual and motorised spring closing mechanism
,electrical closing and opening arrangement and
internal panel wiring with provisions of 2- overcurrent &
1- earth fault combined relay, auxilliary relays, 1- volt
meter with selector switch, 3- ammeter, C.T. operated
static trivector/ multi functional energy meter, 1- CT
operated static KWH meter. Breaker capacity800 Amps
continuous currentCTR 300 /1-1-0.577 Amp with panel
top mounted P.T. of PTR 11KV / √3 / 110V / √3 with
integral earthing facility and internal arc tested for
transformer incoming panel as required and as per
relevant ISS.
2
No.
1
No.
2
No.
Page 223
4
No.
4
No.
2
No.
10 11 KV Vaccum Circuit breaker , Control & relay
panel simplex type, 800 A continuous current 350
MVA rupturring capacity complete with electrical closing
mechanism with internal wiring 2- overcurrent & 1earth fault combined relay,. auxilliary relays,3- ammeter,
1-Volt Meter, C.T. operated static trivector meter/ Multi
functional Energy meter. 1- CT operated static KWH
meter with 3 sets of C.T. of Ratio 200 / 1-1 A with
integral earthing facility and internal arc tested for11 KV
out going feeders as per relevant ISS and as required..
6
No.
5
No.
10.85
MT
10.85
MT
1.8
MT
1.8
MT
Lot
Lot
Lot
Lot
11 Supply and Erection of Galvanised steel structure and
Nuts & Bolts, spring washer etc as required for 33 KV
Tower gangtry, Post Insulators and equipments
a) Steel structure
b) Nuts & bolts, spring washer and foundation bolts etc.
12 Supply, erection, testing & commissioning of substation busbar & stringing materials for 33 KV bus.
a) ACSR (DOG) 7/1.57/6/4.72 mm (DOG ) conductor.
b) 40mm dia. Al. pipe for equipment bus of current
carrying capacity 400 Amps.
c) 7/3.15mm earth wire for substation shielding.
d) Ball & socket type 70 KN, 11KV disc Insulator.
e) Al. tension clamps. 3 -U bolt type, ball& socket type,
suitable for70KN Disc Insulator and ACSR DOG
conductor.
f) 33 KV post insulator
g ) Suspension Clamp suitable for ACSR, DOG
Conductor.
h)"T" Clamp suitable for ACSR DOG Conductor.
i)"T" Clamp suitable for ACSR DOG Conductor in one
end & 40mm dia. Al. tube in other end.
Page 224
j) Bimetalic clamps suitable for isolator, C.T, P.T.,
breaker, transformer& L.A. etc.
13 11 / 6.35(E) XLPE power cable
a) 240 mm Sq. single core (for 3.15 MVA
transformer connection).
b) 185 mm Sq. 3- core(for out going feeder)
14 Outdoor type heat shrink joint kit for 11 KV XLPE
cable of size :a) 240 mm sq. single core
b)185 mm sq. 3- core
15 Indoor type heat shrink jointing kit for II KV XLPE
cable of size :a ) 240 mm sq. single core
b ) 185 mm sq. 3- core
16 1100 V grade XLPE insulated & PVC sheathed
armoured Al. cable of size, 70mm sq. 3½ Core
cable.
17 Supply, laying, termination etc. of control cable
1100V, PVC insulated, PVC sheathed 2.5 mm sq
copper conductor.
a) 12-Core
b) 7-Core
c) 4-Core
d) 2-Core
18 Supply of 40mm dia hot Dip perforated Heavy duty
G.I pipe of length 3 mtr and providing earthing
as per latest ISS: at 33 KV & 11KV switch yard
including pair of GI clamps and nuts & bolts as
required as per REC specification, drawing as
stipulated herein after .
19 Supply and laying of GI flat 50 X 6 mm size for inter
connection of earth electrodes and earthing
terminals of equipments, structures including
welding in joints as required for mesh earthing.
20 Supply & erection of 90 pound lb rail for transformer
rail track.
0.5
Km.
0.5
Km
0.75
Km.
0.75
Km
7
7
No.
No.
7
7
No.
No.
7
7
No.
No.
7
7
No.
No.
0.2
Km
0..1
Km
Lot
Mtr
Lot
Mtr
18
No.
18
No.
300
Mtr.
300
Mtr.
1.5
MT.
1.5
MT.
Page 225
21
22
Supply,Installation & commissioning of 110V, 240
AH capacity Sealed & Maintenance Free (SMF)
Battery Bank comprising of 55 Nos.'Standby Valve
Regulated Lead Acid (VRLA) Cells' of 2 Volt each
(Average Discharge Voltage 1.90 VPC) as per
specification in the Bidding / Tender Document.
1
Unit
1
Unit
Battery Charger with ±1% Digitally Controlled
Regulation suitable for above 110 Volt VRLA
Battery Bank with Float and Boost (FC & BC)
charging arrangement with all Standard protections
housed in free Standing Cabinet of 2.0 mm.
gauge as per specification detailed in the Bidding /
Tender Document.
1
Unit
1
Unit
1
Unit
1
Unit
23 Supply, erection, testing & commissioning of 110V
D.C distribution panel made of sheet steel (14
SWG) and suitable for floor mounting. The
distribution panel shall incorporate the following :a) 1-No, 32 Amp. 110V Air break circuit breaker,
Double pole for the battary incomming supply with
red & green indicating lamps.
b) 1-No earth leakage indicating lamp.
c) 1-No ammeter (range 0-50 A).
d) 1-No volt meter (Range 0-150 V).
e) 4-Nos 16 Amps 110V double pole miniature Circuit
breaker with over load protection for DC outgoing
circuit . The unit will be complete with necessary
internals wiring. Input & outgoing terminals, earthing,
points & rating plate.
24 Supply, Erection, testing & commissioning of 433/450V,
3 Ph. 4 wire 50 Hz, AC distribution board enclosed in
sheet steel (14 SWG) floor mounting type (vertical)
comprising the following:a) 200 Amp 3-Ph 4-wire , 415 V TPN switch fuse unit
(HRC type) as incomming switch.
Page 226
b) 200 Amp 3-Ph. 4-wire , 415 V Al. bus bar having the
following outgoing switch facilities.
i) 100 Amp 415 V 3 ph. 4 wire switch (HRC- type): - 1
No.
ii) 63 Amp 415 V 3 ph. 4 wire switch (rewireable type): 2 Nos.
1
Unit
1
Unit
a) 9 KV, 5 KA, single pole, Metal oxide gapless
surge type LA suitable for nominal system voltage
of 11 KV, 3-Ph., 50 Hz AC supply, creepage
distance 600 mm. conforming to ISS: 3070 / 1985.
21
No.
21
No.
b) 9 Mtr. Long steel tubular pole of designation 410SP-31 conforming to ISS: 2713 / 1980 with base
plate complete.
12
No.
12
No.
c ) Steel materials (Angles & channels).
d) 45 KN, 11KV disc insulator with 3 U Bolt type
disc fittings.
e ) 11 KV, 10 KN pin insulator including G.I. pin.
1.2
MT
1.2
MT
75
No.
75
No.
60
No.
60
No.
f) 11 KV 3 pole GOS ( Air break type ) -400A.
g) 11KV 3 pole DOF for station transformer 200A.
15
No.
15
No.
1
Set
1
Set
300
250
0.3
Kg
Kg
Km
300
250
0.3
Kg
Kg
Km
6
No.
6
No.
iii) 32Amp 250 V 1 ph.2 wire switch (rewireable type): - 2
Nos.
iv) 16Amp 250 V 1 ph.2 wire switch (rewireable type): 3 Nos.
c) AC voltmeter (Range 0- 500 V) with selector switch
(RYB): - 1No.
d) AC Ammeter (Range 0- 300 V) for (RYB) phase : 3Nos.
25 11 KV outgoing bus bar materials
h) Nuts & bolts assorted size
i) 50X6 mm M.S flat for clamp
j) ACSR (DOG ) 7/1.57/6/4.72 mm.
26 Supply & erection of fire fighting equipment with
complete accessories .
a) G.I bucket - 10 ltrs capacity with wooden / iron
stand.
Page 227
NR
NR
b) Portable fire extinguisher using CO2 with
pressure indicator: -5Kg.
c) ABC powder fire extinguisher "Mono Ammonium
phosphate".
i) 5- Kg
ii) 2- Kg
27 Supply, erection, testing & commissioning of 100
KVA, 11/0.43 KV, DY- 11 distribution
transformer for station load.
28 Supply,fabrication,erection including grouting as
required of 7.5 Mtr long GI support (heavy duty
type) having bottom length 4.5 mtr. of dia 65 mm
and upper length of 3 mtr. and 40 mm. dia. For
Switchyard lighting.
29 Switchyard lighting complete with 250W, 230V,
HPSV luminaries with switchgear complete with the
support of item 28 including required wiring through
the pipe and provision of control gear( MCB) for
individual lantern / lamp as required and per
direction of Engineer in charge .
3
No.
3
No.
NR
NR
2
2
No.
No.
2
2
No.
No.
NR
NR
NR
NR
1
No.
1
No.
16
No.
16
No.
10
Unit
10
Unit
NR
NR
30 Shock treatment chart (Laminated )
2
NR
NR
31 Artificial respirator
32 Rubber insulating mat at 15 KV tested of size
(1X2) mtr.
33 Oill filtration plant of capacity 250 G.P.H. (NIRMAL
BRAND / John Fowler).
34 a) Hand driven Insulation Tester 5KV (WACO
make),10000 M-ohm minimum.
35 a) Hand driven Insulation Tester 2.5KV (WACO
make),10000 M-ohm minimum.
36 Chain pully block ( 5 ton capacity )
2
No.
No.
NR
NR
4
No.
NR
NR
1
No.
1
No.
NR
NR
1
No.
NR
NR
1
No.
NR
NR
1
No.
NR
NR
37 Pulling & lifting machine ( TIRFOR ) 5 ton /
capacity.
Page 228
38
c) Digital clamp meter capable of measuring
Various parameters(RMS values for Voltage &
Current):AC Current 40/400Amps.AC Voltage:
600V, DC Voltage 600V, Resistance 40MegaOhm
with LCD Display.Data Hold, Audible continuity,
Diode Test, Over Range Indication,Low Battery
Indication,etc. shall be avilable in the meter.etc.as
per standard specification and perovisions.
1
No.
NR
NR
1
Set
NR
NR
4
Pair
NR
NR
2
Set
NR
NR
1
No.
1
Set.
NR
NR
44 TAPARIA make ring rances.
1
Set.
NR
NR
45 TAPARIA make insulating screw driver.
1
1
Set.
No.
NR
NR
NR
NR
2
Set
NR
NR
1
No.
NR
NR
2
No
NR
NR
50 Best Quality Plastic Chair with arm.
18
No
NR
NR
51
Steel Almirah ( with one locker) 60"x36"x18"
8
No
NR
NR
52 Steel Table half Secretariate with Laminated Sheet
top & with three drawers including automatic
locking device to the right side. Storage Unit Size:
H. 20"xW.14"xD.21"
8
No
NR
NR
39 Complete Tool Box with Box Spanner (1 each of
TAPARIA make product no. 1720, 1722, 1725,
1728 and 17301.
40 15 KV grade hand gloves.
41 Taparia make Allen key set of 2 different range .
42 Oil testing set with input volt 230 , 50 Hz single
phase out put 0-100 KV I/C necessary accessories
conforming releveant IS.
43 TAPARIA make double ended spanner.
46 4-Point earth tester.
47 33 KV discharge Rod of 3 section made of fibre
glass tube complete with all accessaries as per
specification.
48 Crimping tool AAKASH-100 Capacity 6 mmsqr- 400
mm sqr. Weight 5.8 Kg.
49 Steel Leaning Bench(8'ftX16''inch Long)
Page 229
53 Steel tubulor Chair(with cush-ioned seat and back
with arm)(Squire pipe)
4
No
198
Nos
198
Nos
117
set
18
Set
117
Nos
585
Kg
NR
SCHEDULE -B (33 KV Line)
1
Supply and erection of steel tubular pole
conforming to ISS 2713 (P-I & II) 1980 with base
plate direct in earth including excavation, refilling
and ramming etc. as required complete (1 /6th of
the length of the pole to be embedded in earth).
a) 10 mtr long steel tubular pole 410-SP-44.
2
3
4
Supply and erection of painted stay set complete
direct in earth with 16 mm. dia. 1.8 mtr. long
painted stay rod, anchor plate of size 300 X 300 X
8 mm. thick, turn buckle of length 356 mm. with 300
mm. long threaded adjustable 16 mm. dia. MS rod
and thimble including supply & erection of 33 KV
guy insulator as per IS specification, hot dip (heavy
duty) galvanized stay stranded wire of size 7/2.5
mm. grade - IV as per ISS:2141/1979 having
minimum tensile strength 700N mmsq. with Zinc
coating (heavy type coating conforming to
IS:4826/1979, weight 260 Kg. 1 Km.) fastened with
stay clamps as required.
Supply of 33 KV Stay insulator.
Supply of galvanized Stay stranded wire of size
7/2.50 mm
Page 230
NR
5
6
7
8
9
Supply,Erection, fitting & fixing of 1.8 m long
fabricated Cross arm for four pole/two pole
structure made up of (100x50x50x6)mm M.S.
channel on Pole with 4 machine made holes for its
fixing on poles and 3 machine made holes for fixing
on it 3 nos.for strings of disc insulator comprising 3
Discs in each string with the support of Back clamp
and nuts & Bolts etc. as required and as per design
and drawing to be specified by TSECL as per REC
Standards.( for 4 Pole Locations & Double pole)
for pin.
Supply,Erection, fitting & fixing of 1.8m long
fabricated 4 Pole Cross arm made up of
(100x50x50x6)mm M.S. channel for pin insulator.
Supply,Erection, fitting & fixing of 1.5m long
fabricated 1 Pole Cross arm made up of
(100x50x50x6)mm M.S. channel for pin insulator.
Supply,Erection, fitting & fixing of 0.3m long
fabricated 1 Pole Cross arm made up of
(100x50x50x6)mm M.S. channel for pin insulator.
Supply, Erection, fitting & fixing of fabricated
Double Pole" / "four pole"Guard bracket made of
2.1 mtr (65x65x6)mm M.S.Angle and machine
drilled holes on brackets ( 4 Nos. of holes for
double pole bracket) for fixing to poles with Clamp
and another 2 holes at both ends of such brackets
to hold continued G.I. earth Wire as per
design,drawing and engineering requirement of
TSECL as per REC Standards as follows:
82
6
116
116
41
Nos
82
Nos
6
Nos
99
Nos
116
Nos
41
Page 231
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
Nos
Nos
Nos
Nos
Nos
10
11
12
Supply, Erection, fitting & fixing of fabricated
Double Pole" / "four pole"Guard bracket made of
1.8 mtr (65x65x6)mm M.S.Angle and machine
drilled holes on brackets ( 4 Nos. of holes for
double pole bracket) for fixing to poles with Clamp
and another 2 holes at both ends of such brackets
to hold continued G.I. earth Wire as per
design,drawing and engineering requirement of
TSECL as per REC Standards as follows:
Supply, Erection, fitting & fixing of fabricated
Double Pole" / "four pole"cross basing bracket
made of 2.54 mtr (65x65x6)mm M.S.Angle and
machine drilled holes on brackets ( 4 Nos. of holes
for double pole bracket) for fixing to poles with
Clamp and another 2 holes at both ends of such
brackets to hold continued G.I. earth Wire as per
design,drawing and engineering requirement of
TSECL as per REC Standards as follows:
Supply, Erection, fitting & fixing of fabricated
Double Pole" / "four pole"cross basing bracket
made of 1.8 mtr (65x65x6)mm M.S.Angle and
machine drilled holes on brackets ( 4 Nos. of holes
for double pole bracket) for fixing to poles with
Clamp and another 2 holes at both ends of such
brackets to hold continued G.I. earth Wire as per
design,drawing and engineering requirement of
TSECL as per REC Standards as follows:
13 Supply,fitting & fixing of 70 KN,11 KV ball & socket
type disc insulator with cap, pin bolt & W clips
(phosphor bronze; etc complete as per latest ISS
731-1971 and related latest amendments.(3
nos.Disc Insulator in 1 Set)
NR
41
Nos
41
Nos
NR
82
Nos
82
Nos
NR
82
Nos
82
Nos
228
Nos
228
Nos
Page 232
NR
14
Supply,fitting & fixing of accessories suitable for
11KV Ball & socket type 70KN Disc insulator
and ACSR conductor (7/1/6/ 4.73mm) "DOG "as
per ISS and latest amendment for tension
insulator string comprising following & all other
accessories necessary.
a
b
c
d
e
f
g
15
Ball Clevis.
Tension clamp 3 U Bolt Type .
Galvanised "U" bolts & nuts.
Galvanised Spring washer.
Flat washer.
Split pin mild steel
Phosphor bronze"U" Clip
Supply & erection of hot dip galvanised MS forged
33 KV pin ( L-230P) suitable for 33 KV pin insulator
complete with galvanized hexagonal nuts, G.I flat
washer & G.I spring washer conforming to ISS:
2486 (P-II)/1974. The shunk length shall be 100
mm. & erection of brown glazed porcelain pin
16 Supply
insulator for 33 KV system with minimum
creeapage 580 mm with mechanical strength 10 KN
conforming to ISS: 731 /1971 to mach with 33 KV
G.I pin ( L-230P).as per ISS: 2486 (P-II)/1974
17
18
Supply,laying,hoisting & stringing of DOG ACSR
conductor of size (7/1.57/6/4.72mm.) conforming
to IS 398(Part-IV) I974 including binding
jumpering etc with P.G.Clamp as required.
Supply,hoisting, erection & stringing of 8 SWG GI
wire(4mm dia) conforming to ISS:280/1978 and
latest related amendments with heavy coating Zinc
conforming to ISS:4826/1979 i/c laying,
hoisting,binding & jumpering etc as reqd.
228
set
0
0
348
Nos
348
Nos
348
Nos
348
Nos
21
Km
21
Km
1610
Kg
14
Km
Page 233
19
Supply, fitting fixing of fabricated M.S. clamp with
necessary machine mads hole for fixing of different
type of cross arm with poles /Stay sets made up of
50x6 mm M.S. flate with 2 coats of red oxide primer
paint and 1 coat of Al. paint of approved quality
20 Supplyof machine made full threaded M.S. nuts &
bolts of assorted size (16x50 mm to 12x300 mm)
conforming to ISS 1363 of 1960 and latest
amendments.
21 Supply,fitting & fixing of 33 KV Danger plate as per
ISS - 2551 of 1963 and latest amendments with the
help of 12 SWG G.I.wire..
22 Supply & erection of 12 SWG. G.I barbed wire, 2ply, 4 points a 3 " part for generating Engineering
purpose having zinc contain as per ISS: 4826/1968
23 Providing cradle guards by 8 SWG G.I. wire
between earth wire across road crossing,river
crossing etc.
24
Grouting of steel tubular poles / stay sets in 1 : 3 : 6
(1 cement : 3 River Sand : 6 brick aggregate with
20 mm nominal size) i/c. supply of cement ,sand &
brick aggregate , excavation, masionry work, back
filling of earth,carrying etc. as required along with
the cost of centering and shuttering (0.15cum/pole
& 0.027cum/stay)
794
Nos
794
Kg
198
Nos
29
Nos
396
Kg
64
Nos
840
Nos
32.859
60
26 Painting one or more coats with superior ready
mixed paint for steel work of approved quality in all
shades on new work to give an even shade
including priming coat with cross arms.
198
Page 234
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
Nos
320
25 Providing spike earthing with GI rod 1.8 mtr. Long
and 20 mm dia including connecting clamps,blts etc
alongwith drawing of earth wire (8 SWG GI wire )
from earth spike to metals parts pole structure and
excavation, refilling, ramming etc. as required as
per direction of the Engineer-in-charge.
NR
Cum
Nos
Nos
27
Providing of Vehicle with valid registration and
driver with Licence (MARUTI OMNI) for conveyance
of Supervisiory staff/ officers including supply of
Fuel & Lubricants as required time to time.
NR
NR
30
Days
20.00
cum
NR
NR
200.00
cum
NR
NR
17.45
cum
NR
NR
140.00
cum
NR
NR
SCHEDULE - C
R.C.C FRAMED CONTROL ROOM BUILDING
(DOUBLE STORIED)
1
2
3
4
SUBHEAD- EARTHWORK
Earth work in excavation over areas (exceeding 30cm in
depth, 1.5m in width as well as 10 sqm on plan)
including disposal of excavated earth, lead upto 50m
and lift upto 1.5m, disposed earth to be levelled and
neatly dressed.
-All kinds of soil
By manual means
Earth work in excavation in foundation trenches or
drains (not exceeding 1.5 m in width or 10 sqm on plan)
including dressing of sides and ramming of bottoms, lift
upto 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a
lead of 50 m.
-All kinds of soil
By manual means
Extra for additional lift of 1.5m or part thereof
-All kinds of soil
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
-All kinds of soil
Page 235
5
6
Supplying and filling in plinth, under floor, foundations
etc. with sand (fine) from local quarry with all lifts
including spreading in horizontal layers, watering,
grading to required slope, ramming, consolidating and
compacting each layer by using plate compactor or by
any suitable method complete.
100.00
cum
28.87
Litre
120.00
sqm
-All work upto plinth level:
1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone
aggregate 40 mm nominal size)
23.00
cum
1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone
aggregate 40 mm nominal size)
38.00
cum
NR
NR
NR
NR
NR
NR
NR
NR
Diluting and injecting chemical emulsion for PRECONSTRUCTIONAL anti-termite treatment (excluding
the cost of chemical emulsion) and continuous chemical
barrier under and alround the column pits, wall trenches,
basement excavation, top surface of plinth filling,
junction of wall and floor, along the external perimeter of
building, expansion joints, over the top surface of
consolidated earth of which apron is to be laid,
surroundings of pipes and conduits etc. complete as per
specification. The work should be carried out as per IS:
6313 (Part II)- Latest revision [Plinth area of the building
at ground floor only shall be measured for payment] :
With Chlorpyriphos/Lindane E.C. 20% with 1%
concentration.
8
NR
Supplying chemical emulsion in sealed containers
including delivery as specified.
Chlorpyriphos/Lindane emulsifiable concentrate of 20%
7
NR
SUBHEAD-CEMENT CONCRETE WORKS
Providing and laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering -
Page 236
1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone
aggregate 20 mm nominal size)
9
2.9
cum
39.00
cum
1.50
cum
38
cum
103
cum
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
SUBHEAD-R.C.C WORK
Providing and laying in position specified grade of
reinforced cement concrete excluding the cost of
centring, shuttering, finishing and reinforcement-All work upto plinth level:
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
10 Reinforced cement concrete work in walls (any
thickness), including attached pilasters, buttresses,
plinth and skirting courses, fillets, columns, pillars, piers,
abutments, posts and struts etc. upto floor five level
excluding cost of centring, shuttering, finishing and
reinforcementIn walls (any thickness), including attached pilasters,
buttresses, piers, abutments etc.
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
In plinth and skirting courses, fillets, columns, pillars,
posts and struts
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
11 Reinforced cement concrete work in beams, suspended
floors, roofs having slope upto 15° landings, balconies,
shelves, chajjas, lintels, bands, plain window sills,
staircases and spiral stair cases upto floor five level
excluding the cost of centring, shuttering, finishing and
reinforcementRCC work in suspended floors, roofs having slope upto
15° landings, balconies, shelves and chajjas.
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
RCC work in beams, lintels, bands, plain window sills,
staircases and spiral staircases excluding precast spiral
staircase.
Page 237
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
70
cum
1.50
cum
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
12 Providing and laying upto floor five level reinforced
cement concrete work in kerbs, steps and the like
excluding the cost of centring, shuttering, finishing and
reinforcement1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
13
Providing, hoisting and fixing upto floor five level precast
reinforced cement concrete work in shelves including
setting in cement mortar 1:3(1cement : 3 fine sand), cost
of required centring, shuttering, finishing with neat
cement punning on exposed surfaces complete, but
excluding cost of reinforcement with cement concrete
1:2:4 (1cement : 2 fine sand : 4 graded stone aggregate
20mm nominal size).
3.20
cum
Foundations, footings, bases for columns etc. for mass
concrete with timber plank
80.00
sqm
Walls (any thickness) including attached pilasters,
buttresses, plinth and string courses etc. using
shuttering ply
40.00
sqm
Suspended floors, roofs, landings, balconies and access
platform with 12 mm thick shuttering ply
950.00
sqm
Lintels, beams, plinth beams, girders, bressumers and
cantilevers with shuttering ply
700.00
sqm
Columns, Pillars, Piers, Abutments, Posts and Struts
with shuttering ply
580.00
sqm
Spiral staircases (including landing) - cast-in-situ with
ply
45.00
sqm
14 Centering shuttering including struttings, propping etc.
and removal of form work for:
Page 238
15
Providing, hoisting and fixing upto floor five level precast
reinforced cement concrete work in mouldings as in
cornices, windows sills etc. including setting in cement
mortar 1:3(1cement : 3 fine sand), cost of required
centring, shuttering, finishing smooth with 6mm thick
cement plaster 1:3 (1cement : 3 fine sand) on exposed
surfaces complete, but excluding cost of reinforcement
with cement concrete 1:2:4 (1cement : 2 fine sand : 4
graded stone aggregate 20mm nominal size).
NR
NR
NR
NR
1.25
cum
26000.00
kg
51
Cum.
NR
NR
38.50
Cum.
NR
NR
NR
NR
32.00
Sqm.
950.00
Sqm.
NR
NR
16 Reinforcement for R.C.C. work including straightening,
cutting, bending, placing in position and binding all
complete upto floor five level.
Thermo-Mechanically Treated bars/ Cold twisted
deformed steel bars
SUBHEAD- BRICK WORK
17 First class brick work in foundation and plinth including
cost of all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ).
18 First class brick work in superstructure above plinth
level & upto floor-five level including cost of all materials
as required complete:19
In cement mortar 1:4 ( 1 cement : 4 fine sand ).
Half brick masonry work with first class bricks in
foundation and plinth including cost of all materials as
required complete:-
20 Half brick masonry work with first class bricks in
superstructure upto floor five level including cost of all
materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ).
21 Extra for providing & placing in position 2 nos 6mm dia
MS bars at every 6th course of full brick masonry work
including anchorage in joints of 75mm in each side in
superstructure for all level including cost of all materials
as required complete:-
Page 239
In cement mortar 1:4 ( 1 cement : 4 fine sand ).
22 Extra for providing & placing in position 2 nos 6mm dia
MS bars at every 4th course of half brick masonry work
including anchorage in joints of 75mm in each side in
superstructure for all level including cost of all materials
as required complete:-
5.00
Cum.
NR
NR
In cement mortar 1:4 ( 1 cement : 4 fine sand ).
SUBHEAD- WOOD WORK
23 Providing wood work in frames of doors, windows,
clerestory windows and other frames, wrought framed
and fixed in position :
5.00
Sqm.
NR
NR
1
Cum
NR
NR
42.00
Sqm
NR
NR
1900.00
Kg
NR
NR
NR
NR
NR
NR
Karai wood
24 Providing and fixing ISI marked flush door shutters
conforming to IS: 2202 (Part I) decorative type, core of
block board construction with frame of 1st class hard
wood and well matched teak 3 ply veneering with
vertical grains or cross bands and face veneers on both
faces of shutters.
35 mm thick including ISI marked Stainless Steel butt
hinges with necessary screws.
25 Providing and fixing M.S. grills of required pattern in
frames of windows etc. with M.S. flats, square or round
bars etc. all complete.
Fixed to openings /wooden frames with rawl plugs
screws etc.
26
Providing 40 × 5 mm flat iron hold fast 40 cm long
including fixing to frame with 10 mm diameter bolts, nuts
and wooden plugs and embedding in cement concrete
block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand
: 6 graded stone aggregate 20mm nominal size)
108
27
Providing and fixing chromium plated brass 100 mm
mortice latch and lock with 6 levers and a pair of lever
handles with necessary screws etc. complete (best
make of approved quality).
32
Page 240
No
No
28 Providing and fixing aluminium sliding door bolts ISI
marked anodised (anodic coating not less than grade
AC 10 as per IS : 1868) transparent or dyed to required
colour or shade with nuts and screws etc. complete :
300x16 mm
29 Providing and fixing aluminium tower bolts ISI marked
anodised (anodic coating not less than grade AC 10 as
per IS : 1868 ) transparent or dyed to required colour or
shade with necessary screws etc. complete :
26
No
NR
NR
300x10 mm
30 Providing and fixing aluminium handles ISI marked
anodised (anodic coating not less than grade AC 10 as
per IS : 1868) transparent or dyed to required colour or
shade with necessary screws etc. complete :
120
No
NR
NR
65
No
NR
NR
18
No
NR
NR
NR
NR
125 mm
31 Providing and fixing aluminium hanging floor door
stopper ISI marked anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade with necessary screws etc.
complete.
32
Twin rubber stopper
Providing and fixing factory made P.V.C. door frame of
size 50x47mm with a wall thickness of 5mm, made out
of extruded 5mm rigid PVC foam sheet mitred at corners
and joined with 2 Nos. of 150mm long brackets of
15x15mm M.S. square tube, the vertical door profiles to
be reinforced with 19×19mm MS square tube of 19
gauge, EPDM rubber gasket weather seal to be
provided through out the frame . The door frame to be
fixed to the wall usuing MS screws of 65/100 mm size
complete as per manufacturers' specification and
direction of Engineer-In-Charge.
70.00
Page 241
mtr.
33 Providing and fixing to existing door frames.
30mm thick factory made solid both side prelam panel
PVC door shutter consisting of frame made out of M.S.
tubes of 19 gauge thickness and size of 19mm x 19mm
for styles, top & bottom rails. M.S. frame shall have a
coat of steel primers of approved make and
manufacture . M.S. frame covered with 5mm thick heat
moulded prelam PVC ‘C channel of size 30mm
thickness, 70mm width out of which 50mm shall be flat
and 20mm shall be tapered in 45degree angle on either
side forming stiles; and 5mm thick, 95mm wide PVC
sheet out of which 75mm shall be flat and 20mm shall
be tapered in 45 degree on the inner side to form top
and bottom rail and 115mm wide PVC sheet out of
which 75mm shall be flat and 20mm shall be tapered on
both sides to form lock rail. Top, button and lock rails
shall be provided either side of the panel. 10mm (5mm x
2 ) thick, 20mm wide cross PVC sheet be provided as
gap insert for top rail & bottom rail, panelling of 5mm
thick both side Prelam PVC sheet to be fitted in the M.S.
frame welded/ sealed to the stiles & rails with 7mm
(5mm+2mm) thick x 15mm wide PVC
sheet beading on inner side, and joined together with
solvent cement adhesive. An additional 5mm thick PVC
strip of 20mm width is to be stuck on the interior side of
the ‘C Channel using PVC solvent adhesive etc.
complete as per direction of Engineer-in-charge.
manufacturer’s specification & drawing.
22.00
34
Page 242
NR
NR
NR
sqm
SUBHEAD- STEEL WORK
Providing structural steel work in single section fixed
with or without connecting plate including cutting,
hoisting, fixing in position and applying a priming coat of
approved steel primer all complete as required.
350.00
NR
Kg.
35
Providing and fixing in position collapsible steel shutters
with vertical channels 20x10x2mm at 100 mm centre to
centre and braced with flat iron diagonals 20x5mm size
with top and bottom rail of T-iron 40x40x6mm with
40mm dia. steel pulleys & with riveted bolts, nuts,
locking arrangement, stoppers, handles, hold fast
/anchor bolt including embedding in cement concrete of
required grade for fixing in position, all necessary
fittings, including applying a priming coat of approved
steel primer etc. complete as required.
42.00
Sqm.
4.50
Sqm.
5.40
Sqm.
NR
NR
NR
NR
NR
NR
36 Providing and fixing 1mm thick M.S. sheet door with
frame of 40x40x6mm angle iron and 3mm M.S. gusset
plates at the junctions and corners, & with cleats with
bolts & nuts, rivets, locking arrangement, handles,
hooks & eyes, pinlets including embedding in cement
concrete of required grade for fixing in position, all
necessary fittings, including applying a priming coat of
approved steel primer etc. complete as required:Using M.S. angels 40x40x6 mm for diagonal braces.
37
Supplying and fixing rolling shutters of approved make,
made of required size M.S. laths interlocked together
through their entire length and jointed together at the
end by end locks mounted on specially designed pipe
shaft with brackets, side guides and arrangements for
inside and outside locking with push and pull operation
complete including the cost of providing and fixing
necessary 275mm long wire springs grade No.2 and
M.S. top cover of required thickness for rolling shutters
& with handles, hold fast including embedding in cement
concrete of required grade required for fixing in position,
all necessary fittings, including applying of approved
steel primer etc. complete as required:80xl.25mm M.S. laths with 1.25 mm thick top cover.
Page 243
38
39
Providing and fixing ball bearing for rolling shutters (
exceeding 10 sqm area ) of approved make complete as
required.
4
NR
NR
NR
NR
NR
NR
NR
NR
Each
Providing and fixing circular/ Hexagonal cast iron or
M.S. sheet box for ceiling fan clamp of internal dia
140mm, 73mm height, top lid of 1.5mm thick M.S. sheet
with its top surface hacked for proper bonding, top lid
shall be screwed into the cast iron/ M.S. sheet box by
means of 3.3mm dia. round headed screws, one lock
at the corners. Clamp shall be made of 12mm dia
M.S. bar bent to shape, including painting the exposed
portion as per standard drawing complete as required
(provided incase of low ceiling height).
25
Each
450
Kg.
120
sqm
40 Steel work welded in built up section/framed work
including cutting, hoisting, fixing in position and applying
a priming coat of approved steel primer using steel etc.
complete as required:In grating, frames, guard bar, railing, brackets, gates
and similar works, all complete.
SUBHEAD-FLOORING WORK
41 Providing and laying polished vitrified floor tiles in
different sizes ( thickness to be specified by the
manufacturer ) with water absorption less than 0.08 %
and conforming to IS : 15622 of approved make in all
colours, shades over 20 mm thick bed of cement mortar
1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary
cement slurry including pointing with white cement
mixed with pigment of matching shade complete.
Size of tile 60x60 cm
42 Providing and fixing precast chequered cement concrete
tiles 22 mm thick, laid in footpath & courtyard, on 20 mm
thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand
) jointed with neat cement slurry mixed with pigment to
match the shade of tiles including rubbing and polishing
complete.
Page 244
In dark shade using ordinary cement
43 Providing and fixing 1st quality ceramic glazed wall tiles
conforming to IS : 15622 ( thickness to be specified by
the manufacturer ) of approved make in all colours,
shades except burgundy, bottle green, black of any size
as approved by Engineer-in-charge in skirting, risers of
steps and dados over 12 mm thick bed of cement mortar
1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary
cement slurry including pointing with white cement
mixed with pigment of matching shade complete.
35.00
175.00
sqm
NR
NR
NR
NR
NR
NR
NR
NR
sqm
44 Providing and laying 1st quality ceramic glazed floor
tiles 300 x 300 mm conforming to IS : 15622 ( thickness
to be specified by the manufacturer ) of approved make
in colours, shades such as white, ivory, grey, fume red,
brown over 20 mm thick bed of cement mortar 1 : 4 ( 1
cement : 4 fine sand ) jointed with ordinary cement
slurry including pointing with white cement mixed with
pigment of matching shade complete.
80.00
sqm
130.00
sqm
45 Providing and fixingr Kota stone in floors over 20 mm
thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand
) jointed with ordinary cement slurry including pointing
with ordinary cement mixed with pigment of matching
shade, including rubbing and polishing complete.
Kota stone slab 30mm thick
46 Providing and laying 40 mm. thick marble chips flooring
rubbed and polished to granolithick finish under layer 34
mm. thick cement concrete 1:2:4 ( 1 ordinary cement: 2
fine sand: 4 graded stone aggregate 12.5 mm.size) and
top layer 6 mm. thick with white, black, chocolate , grey,
yellow, pink, blue or green marble chips from 1 mm. to 4
mm. nominal size laid in cement marble powder mix 3:1(
1 cement: 1 marble powder) by weight in proportion of 4:
7(4 cement marble powder mix: 7 marble chips) by
volume including cement slurry etc. complete
Page 245
Using light shade pigment with ordinary cement in top
layer
47 Providing and laying 40 mm. marble chips skirting( upto
300 mm. height) rubbed and polished to granolithick
finish, top layer 6 mm. thick with white, black, chocolate
, grey, yellow, pink, blue or green marble chips of sizes
from 1 mm. to 4 mm. nominal sizes laid in cement
marble powder mix 3:1( 1 cement: 1 marble powder) by
weight in proportion of 4: 7(4 cement marble powder
mix: 7 marble chips) by volume including cement slurry
etc. complete.
Using light shade pigment with ordinary cement in top
layer
160.00
sqm
20.00
sqm.
90.00
Kg.
NR
NR
NR
NR
NR
NR
SUBHEAD-ALUMINIUM WORK
Providing and fixing aluminium work for doors,
windows, ventilators, stair railing including hand rail and
partitions with extruded built up standard tubular
sections/ appropriate Z sections and other sections
of approved make conforming to IS: 733 and IS : 1285,
fixed with rawl plugs and screws or with fixing clips, or
with expansion hold fasteners including necessary
filling up of gaps at junctions, at top, bottom and sides
with required PVC/neoprene felt etc. aluminium sections
shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
aluminium snap beading for glazing / paneling, C.P.
48 brass / stainless steel screws, all complete as per
architectural drawing and the direction of
Engineer-in-charge. (Glazing and paneling to be paid
for separately) :-
For fixed portion of approved quality:Anodised aluminium (anodised transparent or dyed
to required shade according to IS: 1868, Minimum
anodic coating of grade AC 15).
Page 246
49 For shutters/ sliding shutters of doors, windows &
ventilators including providing and fixing hinges / pivots
/ rollers and making provision for fixing fittings wherever
required including the cost of PVC / neoprene gasket
required of approved quality ( Fittings shall be paid for
separately ):Anodised aluminium (anodised transparent or dyed
to required shade according to IS: 1868, Minimum
anodic coating of grade AC 15).
450
Kg.
With glass/ float glass panes of 5.5 m thickness ( weight
not less than 13.50 kg / sqm )
92.00
Sqm.
With glass/ float glass panes of 4.0 m thickness (
weight not less than 10.0 kg / sqm )
17.40
Sqm.
1
Each
NR
NR
NR
NR
NR
NR
NR
NR
50 Providing and fixing glazing of approved quality in
aluminium doors, windows, ventilator, shutters and
partition frames with PVC / neoprene gasket etc.
complete as per architectural drawing and the direction
of Engineer-in-charge :-
51 Providing and fixing double action hydraulic floor spring
of approved brand and manufacture ( conforming to IS :
6315 ) for aluminium doors including cost of cutting
floors as required, embedding in floors and cover plates
etc. complete as per direction of the Engineer-in-charge:-
With stainless steel cover plate.
Page 247
52 Providing and fixing aluminium work consisting of tee /
angle sections, of approved make conforming to IS : 733
in frames of false ceiling including aluminium angle
cleats with necessary C.P. brass / stainless steel sunk
screws, aluminium perimeter angles fixed to wall with
rawl plugs @ 450 mm centre to centre and fixing the
frame work to 6 mm dia G.I. level adjusting hangers with
necessary cadmium plated machine screws all complete
as per architectural drawing and the direction of
Engineer-in-charge ( level adjusting hangers, ceiling
cleats and expansion hold fasteners to be paid for
separately ):-
Anodised aluminium (anodised transparent or dyed to
required shade according to IS : 1868 , minimum anodic
coating of grade AC 15 ).
8.75
53 Providing and filling the gap in between aluminium frame
and adjacent RCC / brick work by providing weather
silicon sealant over backer rod of approved quality etc.
complete as per architectural drawing and direction of
the Engineer-in charge:- (i) Upto 5 mm depth and 5 mm
width.
NR
NR
NR
NR
NR
NR
Kg.
50.00
Metre
12.00
Sqm.
54 Providing and fixing 12 mm thick prelaminated three
layer medium density (exterior grade ) particle board
grade-I, type II conforming to IS : 12823 bonded with
phenol formaldehyde synthetic resin, of approved brand
and manufacture in panelling fixed in aluminium doors,
windows, shutters and partition frames with C.P. brass /
stainless steel screws all complete as per architectural
drawing and the direction of Engineer-in-charge :Prelaminated particle board of approved quality with
decorative lamination on both side.
55 Providing and fixing aluminium casement windows
fastener of required length for aluminium windows with
necessary screws etc. of approved quality complete as
per direction of Engineer-in-charge:-
Page 248
Anodised aluminium of grade AC 15 ).
56 Providing and fixing aluminium tubular handle bar of 32
mm outer dia, 3.0 mm thick and 2100 mm long with
Stainless Steel screws etc. of approved quality complete
as per direction of Engineer-in-charge:-
10
Each
NR
NR
Anodised aluminium of grade AC 15 ).
57 Providing and fixing 100 mm brass locks ( best make of
approved quality ) with 6 levers without pair of handles
for aluminium doors including necessary cutting and
making good etc. complete as per direction of Engineerin-charge.
5
Each
NR
NR
NR
NR
5
Each
90.00
m
NR
NR
15
each
NR
NR
20
each
NR
NR
SUBHEAD- ROOFING WORK
58 Providing and fixing on wall face unplasticised Rigid
PVC rain water pipes (working pressure 4 kg / cm2)
conforming to IS : 13592 Type A including jointing
with seal ring conforming to IS : 5382 leaving 10
mm gap for thermal expansion:
Single socketed pipe - 110 mm OD
59 Providing and fixing on wall face unplasticised - PVC
moulded fittings/ accessories for unplasticised Rigid
PVC rain water pipes conforming to IS : 13592 Type
A including jointing with seal ring conforming to IS :
5382 leaving 10 mm gap for thermal expansion:
Coupler
110 mm
Bend 87.5°
110mm
Page 249
60 Providing and fixing unplasticised -PVC pipe clips of
approved design to unplasticised - PVC rain water
pipes by means of 50x50x50mm hard wood plugs,
screwed with M.S. screws of required length
including cutting brick work and fixing with cement
mortar 1 : 4 (1cement : 4 fine sand) making good the
wall etc. complete.
110mm
SUBHEAD- FINISHING WORK
61 12 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
60
each
NR
NR
In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
62 15 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
1840.00
sqm
NR
NR
In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
63 6 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
950.00
sqm
NR
NR
In cement mortar 1 : 3 ( 1 cement : 3 fine sand )
64 Neat cement punning.
65 Extra for providing and mixing water proofing material in
cement plaster work in proportion recommended by the
manufacturers.
540.00
280.00
sqm
NR
NR
sqm
NR
NR
NR
NR
50.00
kg
66 Providing and applying plaster of paris putty of 2 mm
thickness over plastered surface to prepare the surface
even and smooth complete.
NR
NR
1210.00
sqm
67 Applying one coat of cement primer of approved brand
and manufacturer on wall surface complete.
1350.00
sqm
NR
NR
NR
NR
68 Finishing walls with premium acrylic smooth exterior
paint of required shade of approved brand and
manufacture on new work ( two or more coats applied
@ 1.43 kg/10 sqm ) over and including base coat water
proofing cement paint applied @ 2.20 kg/10 sqm
complete.
860.00
Page 250
sqm
69 Applying priming coat:
With ready mixed pink primer of approved brand and
manufacture on wood work ( hard & soft wood ).
With ready mixed red oxide zinc chromate primer of
approved brand and manufacture on steel, galvanised
iron / steel work.
25.00
sqm
120.00
sqm
80.00
sqm
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
70 Finishing with epoxy paint ( two or more coats ) of
approved brand and manufacture at all locations
prepared and applied as per manufacturer's
specification on new work including appropriate priming
coat, preparation of surface etc. complete.
On steel work
71 Wall painting with plastic emulsion paint ( two or more
coats ) of required colour of approved brand and
manufacture on new work to give an even shade.
72 Painting with black anticorrosive bitumastic paint ( two
or more coats ) of approved brand and manufacture on
new work to give an even shade.
1450.00
sqm
35.40
sqm
8
each
SUBHEAD- SANITARY WORK
73 Providing and fixing water closet squatting pan (Indian
type W.C. pan ) with 100mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing cistern with
manually controlled device (handle lever) conforming
to IS : 7231, with all fittings and fixtures complete
including cutting and making good the walls and floors
wherever required :
White Vitreous china Orrisa pattern W.C. pan of size
580x440 mm with integral type foot rests.
Page 251
74 Providing and fixing white vitreous china pedestal
type water closet (European type W.C. pan) with
seat and lid, 10 litre low level white P.V.C. flushing
cistern with manually controlled device (handle lever),
conforming to IS : 7231, with all fittings and fixtures
complete including cutting and making good the walls
and floors wherever required :
W.C. pan with ISI marked white solid plastic seat and lid
4
each
8
each
White Vitreous China Wash basin size 630x450 mm
with a single 15 mm C.P. brass pillar taps.
6
each
77 Providing and fixing white vitreous china pedestal for
wash basin completely recessed at the back for the
reception of pipes and fittings.
6
each
12
each
6
each
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
75 Fixing white vitreous china flat back half stall urinal
of size 580x380x350mm with white PVC automatic
flushing cistern, with fittings, standard size C.P.
brass flush pipe, spreaders with unions and clamps
(all in C.P. brass) with waste fitting as per IS : 2556, C.I.
trap with outlet grating and other couplings in C.P.
brass including painting of fittings and cutting and
making good the walls and floors wherever required :
Single half stall urinal with 5 litre P.V.C. automatic
flushing cistern.
76 Providing and fixing wash basin with C.I. brackets, 15
mm C.P. brass pillar taps,32 mm C.P. brass waste of
standard pattern, including painting of fittings and
brackets, cutting and making good the walls
wherever require :
78 Providing and fixing P.V.C. waste pipe for sink or wash
basin including P.V.C. waste fittings complete.
Flexible pipe
32 mm dia
79 Providing and fixing 100 mm sand cast Iron grating for
gully trap.
Page 252
80 Providing and fixing 600x450 mm bevelled edge mirror
of superior glass (of approved quality) complete with 6
mm thick hard board ground fixed to wooden cleats with
C.P. brass screws and washers complete.
8
600mm long towel rail with total length of 645mm, width
78mm and effective height of 88mm, weighing not less
than 190gms.
8
each
6
each
8
Page 253
NR
NR
NR
NR
NR
NR
NR
NR
each
84 Providing and fixing PTMT liquid soap container 109mm
wide, 125mm high and 112mm distance from wall of
standard shape with bracket of the same materials with
snap fittings of approved quality and colours weighing
not less than 105 gms
8
NR
each
81 Providing and fixing 600x120x5mm glass shelf with
edges round of supported on anodised aluminium angle
frame with C.P. brass brackets and guard rail complete
fixed with 40 mm long screws, rawl plugs etc., complete.
82 Providing and fixing terminal guard:
100 mm
Sand cast iron S&S as per IS - 3989
83 Providing and fixing PTMT towel rail complete with
brackets fixed to wooden cleats with CP brass screws
with concealed fitting arrangement of approved 450mm
long towel rail with total length of 495mm, 78mm wide
and effective height quality and colour.
NR
each
85 Providing, fixing and laying rigid UPVC pipes conforming
to IS :4985 jointing with couplers, of same class
conforming to IS : 10124 ( Pt-II ) with solvent cement
conforming to IS : 14182 including testing of joints
complete ( but excluding the cost of specials like bend,
tees etc. which will be paid separately ) as per chapter
20 of CPWD specification and direction of the Engineer in - charge.
Class - 3 ( working pressure 6.0 kg / cm2)
90 mm OD
110 mm OD
86 Providing, fixing and laying fabricated UPVC bend of
required degree conforming to IS : 10124 ( part 8 / 9 / 10
/ 11 / 12 / 13 ) with solvent cement conforming to IS :
14182 including testing of joints complete as per chapter
20 of CPWD specification and direction of the Engineer in - charge.
52.00
85.00
Metre
NR
NR
Metre
NR
NR
90 mm OD
110 mm OD
87 Providing, fixing and laying fabricated UPVC equal tee
conforming to IS : 10124 ( Part 5 ) with solvent cement
conforming to IS : 14182 including testing of joints
complete as per chapter 20 of CPWD specification and
direction of the Engineer - in - charge.
20
15
No
NR
NR
No
NR
NR
90 x 90 mm dia
110 x 110 mm dia
88 Providing, fixing and laying fabricated UPVC end cap
conforming toIS : 10124 ( Part 4 ) with solvent cement
conforming to IS : 14182 including testing of joints
complete as per chapter 20 of CPWD specification and
direction of the Engineer - in - charge.
7
12
No
NR
NR
No
NR
NR
3
2
No
NR
NR
No
NR
NR
90 x 90 mm dia
110 x 110 mm dia
Page 254
SUBHEAD- WATER SUPPLY INSTALLATION
89 Providing and fixing G.I. pipes complete with G.I. fittings
and clamps, including cutting and making good the walls
etc.
Internal work - Exposed on wall.
15 mm dia. nominal bore
20 mm dia. nominal bore
90 Providing and fixing G.I. pipes complete with G.I. fittings
including trenching and refilling etc.
External work
25 mm dia. nominal bore
40 mm dia. nominal bore
91 Making connection of G.I. distribution branch with G.I.
main of following sizes by providing and fixing tee,
including cutting and threading the pipe etc. complete :
25 to 40 mm nominal bore
92 Making chases upto 7.5x7.5 cm in wails including
making good and finishing with matching surface after
housing G.I. pipe etc.
60.00
55.00
metre
NR
NR
metre
NR
NR
20.00
50.00
metre
NR
NR
metre
NR
NR
2
each
NR
NR
NR
NR
NR
NR
15.00
93 Providing and placing on terrace (at all floor levels)
polyethylene water storage tank ISI : 12701 marked with
cover and suitable locking arrangement and making
necessary holes for inlet, outlet and overflow pipes but
without fittings and the base support for tank.(1000 litre
capacity)x4 nos.
metre
4000
per litre
15 mm nominal bore
95 Providing and fixing C.P. brass long body bib cock of
approved quality conforming to IS standards and
weighing not less than 690 gms.
12
each
NR
NR
15mm nominal bore.
96 Providing and fixing C.P. brass stop cock (concealed) of
standard design and of approved make conforming to
IS:8931.
8
each
NR
NR
12
each
NR
NR
94 Providing and fixing C.P. brass bib cock of approved
quality conforming to IS:8931
15 mm nominal bore.
Page 255
97 Providing and fixing ball valve (brass) of approved
quality complete :
15 mm nominal bore
20 mm nominal bore
25 mm nominal bore
98 Providing and fixing gun metal gate valve with C.I. wheel
of approved quality (screwed end):
40 mm nominal bore
99 Providing and fixing gun metal non-return valve of
approved quality (screwed end):
100 Vertical
40 mm nominal bore
101 Providing and fixing uplasticised PVC connection pipe
with brass unions :
45 cm length
15 mm nominal bore
102 Providing and fixing G.I. Union in G.I. pipe including
cutting and threading the pipe and making long screws
etc. complete (New work)
15 mm nominal bore
20 mm nominal bore
6
9
3
each
NR
NR
each
NR
NR
each
NR
NR
1
each
NR
NR
2
each
NR
NR
6
each
NR
NR
8
each
NR
NR
8
each
NR
NR
NR
25 mm nominal bore
2
each
NR
40 mm nominal bore
2
each
NR
NR
6
each
NR
NR
103 Providing and fixing PTMT grating of approved quality
and colour.
Circular type.
100 mm nominal dia.
SUBHEAD- SEWERAGE & DRAINAGE WORK
Page 256
104 Constructing brick masonry chamber for underground
C.I. inspection chamber and bends with 1st class bricks
in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover
with frame (light duty) 455x610 mm internal dimensions,
total weight of cover with frame to be not less than 38 kg
(weight of cover 23 kg and weight of frame 15 kg)
R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4
graded stone aggregate 20 mm nominal size)
foundation concrete 1:5:10 (1 cement: 5 fine sand : 10
graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1
cement: 3 fine sand) finished smooth with a floating coat
of neat cement on walls and bed concrete etc. complete
as per standard design :
Inside dimensions 455x610 mm and 45 cm deep for
single pipe line :
3
No
1
No
2
No
Inside dimensions 500x700 mm and 45 cm deep for
pipe line with one or two inlets :
NR
NR
NR
NR
NR
NR
105 Supplying and fixing C.I. cover without frame for
manholes :
500 mm diameter C.I. cover (medium duty) the weight of
the cover to be not less than 58 kg.
SCHEDULE -D
R.C.C. FRAMED BOUNDARY WALL
Total Length of Boumdary Wall = 180.00 Meter.
1
Earth work in excavation over areas (exceeding 30cm in
depth, 1.5m in width as well as 10 sqm on plan)
including disposal of excavated earth, lead upto 50m
and lift upto 1.5m, disposed earth to be levelled and
neatly dressed.
-All kinds of soil
Page 257
2
3
4
5
By manual means
Earth work in excavation in foundation trenches or
drains (not exceeding 1.5 m in width or 10 sqm on plan)
including dressing of sides and ramming of bottoms, lift
upto 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a
lead of 50 m.
-All kinds of soil
By manual means
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
-All kinds of soil
Supplying and filling in plinth, under floor, foundations
etc. with sand (fine) from local quarry with all lifts
including spreading in horizontal layers, watering,
grading to required slope, ramming, consolidating and
compacting each layer by using plate compactor or by
any suitable method complete.
cum
NR
NR
137.40
cum
NR
NR
91.60
cum
NR
NR
NR
NR
NR
NR
NR
NR
13.50
cum
27.00
cum
19.75
cum
SUBHEAD-CEMENT CONCRETE WORKS
Providing and laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering -All work upto plinth level:
1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone
aggregate 40 mm nominal size)
6
100.00
SUBHEAD-R.C.C WORK
Providing and laying in position specified grade of
reinforced cement concrete excluding the cost of
centring, shuttering, finishing and reinforcement-All work upto plinth level:
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
Page 258
7
Reinforced cement concrete work in walls (any
thickness), including attached pilasters, buttresses,
plinth and skirting courses, fillets, columns, pillars, piers,
abutments, posts and struts etc. upto floor five level
excluding cost of centring, shuttering, finishing and
reinforcementIn walls (any thickness), including attached pilasters,
buttresses, piers, abutments etc.
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
4.75
cum
15.30
cum
20.435
cum
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
In plinth and skirting courses, fillets, columns, pillars,
posts and struts
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
8
Reinforced cement concrete work in beams, suspended
floors, roofs having slope upto 15° landings, balconies,
shelves, chajjas, lintels, bands, plain window sills,
staircases and spiral stair cases upto floor five level
excluding the cost of centring, shuttering, finishing and
reinforcementRCC work in beams, lintels, bands, plain window sills,
staircases and spiral staircases excluding precast spiral
staircase.
1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone
aggregate 20 mm nominal size)
9
Centering shuttering including struttings, propping etc.
and removal of form work for:
Foundations, footings, bases for columns etc. for mass
concrete with timber plank
45.00
sqm
Walls (any thickness) including attached pilasters,
buttresses, plinth and string courses etc. using
shuttering ply
36.00
sqm
Lintels, beams, plinth beams, girders, bressumers and
cantilevers with shuttering ply
166.50
sqm
Columns, Pillars, Piers, Abutments, Posts and Struts
with shuttering ply
240.60
sqm
Page 259
10 Reinforcement for R.C.C. work including straightening,
cutting, bending, placing in position and binding all
complete upto floor five level.
Thermo-Mechanically Treated bars/ Cold twisted
deformed steel bars
NR
NR
Cum.
NR
NR
245.00
Sqm.
NR
NR
245.00
Sqm.
NR
NR
765.00
Kg.
NR
NR
2430.00
Kg
NR
NR
NR
NR
5525.00
kg
15.35
SUBHEAD- BRICK WORK
11 First class brick work in foundation and plinth including
cost of all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ).
12 Half brick masonry work with first class bricks in
superstructure upto floor five level including cost of all
materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ).
13 Extra for providing & placing in position 2 nos 6mm dia
MS bars at every 4th course of half brick masonry work
including anchorage in joints of 75mm in each side in
superstructure for all level including cost of all materials
as required complete:-
In cement mortar 1:4 ( 1 cement : 4 fine sand ).
SUBHEAD- STEEL WORK
14 Steel work welded in built up section/framed work
including cutting, hoisting, fixing in position and applying
a priming coat of approved steel primer using steel etc.
complete as required:In grating, frames, guard bar, railing, brackets, gates
and similar works, all complete.
15 Providing and fixing M.S. grills of required pattern in
frames of windows etc. with M.S. flats, square or round
bars etc. all complete.
Fixed to openings /wooden frames with rawl plugs
screws etc.
SUBHEAD- FINISHING WORK
Page 260
16 12 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
NR
NR
sqm
NR
NR
144.00
sqm
NR
NR
19 Applying one coat of cement primer of approved brand
and manufacturer on wall surface complete.
810.00
sqm
NR
NR
20 Applying priming coat:
With ready mixed red oxide zinc chromate primer of
approved brand and manufacture on steel, galvanised
iron / steel work.
NR
NR
135.00
sqm
NR
NR
NR
NR
405.00
sqm
405.00
17 15 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
18 Neat cement punning.
21 Finishing walls with acrylic smooth exterior paint of
required shade of approved brand and manufacture on
new work ( two or more coats applied @ 1.67 kg/10 sqm
) over and including base coat water proofing cement
paint applied @ 2.20 kg/10 sqm complete.
810.00
sqm
135.00
sqm
22 Finishing with epoxy paint ( two or more coats ) of
approved brand and manufacture at all locations
prepared and applied as per manufacturer's
specification on new work including appropriate priming
coat, preparation of surface etc. complete.
On steel work
SCHEDULE -E
SWITCH YARD (EQUIPMENT FOUNDATION)
1
Earth work in excavation over areas (exceeding 30cm in
depth, 1.5m in width as well as 10 sqm on plan)
including disposal of excavated earth, lead upto 50m
and lift upto 1.5m, disposed earth to be levelled and
neatly dressed.
Page 261
2
3
5
6
-All kinds of soil
By manual means
Earth work in excavation in foundation trenches or
drains (not exceeding 1.5 m in width or 10 sqm on plan)
including dressing of sides and ramming of bottoms, lift
upto 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a
lead of 50 m.
1260.00
cum
315.00
cum
185.00
cum
-All work upto plinth level:
1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone
aggregate 40 mm nominal size)
88.25
cum
1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick
aggregate 40 mm nominal size)
65.00
cum
105.35
cum
-All kinds of soil
By manual means
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
-All kinds of soil
SUBHEAD-CEMENT CONCRETE WORKS
Providing and laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering -
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
SUBHEAD-R.C.C WORK
Providing and laying in position specified grade of
reinforced cement concrete excluding the cost of
centring, shuttering, finishing and reinforcement-All work upto plinth level:
1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone
aggregate 20 mm nominal size)
Page 262
7
Reinforced cement concrete work in walls (any
thickness), including attached pilasters, buttresses,
plinth and skirting courses, fillets, columns, pillars, piers,
abutments, posts and struts etc. upto floor five level
excluding cost of centring, shuttering, finishing and
reinforcementIn walls (any thickness), including attached pilasters,
buttresses, piers, abutments etc.
1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone
aggregate 20 mm nominal size)
2.75
cum
1.62
cum
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
NR
In plinth and skirting courses, fillets, columns, pillars,
posts and struts
1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone
aggregate 20 mm nominal size)
8
9
Providing, hoisting and fixing upto floor five level precast
reinforced cement concrete work in shelves including
setting in cement mortar 1:3(1cement : 3 fine sand), cost
of required centring, shuttering, finishing with neat
cement punning on exposed surfaces complete, but
excluding cost of reinforcement with cement concrete
1:2:4 (1cement : 2 fine sand : 4 graded stone aggregate
20mm nominal size).
10.50
cum
Foundations, footings, bases for columns etc. for mass
concrete with timber plank
350.85
sqm
Walls (any thickness) including attached pilasters,
buttresses, plinth and string courses etc. using
shuttering ply
23.00
sqm
Columns, Pillars, Piers, Abutments, Posts and Struts
with shuttering ply
21.60
sqm
6725.00
kg
Centering shuttering including struttings, propping etc.
and removal of form work for:
10 Reinforcement for R.C.C. work including straightening,
cutting, bending, placing in position and binding all
complete upto floor five level.
Thermo-Mechanically Treated bars/ Cold twisted
deformed steel bars
Page 263
SUBHEAD- BRICK WORK
11 First class brick work in foundation and plinth including
cost of all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ).
12 Half brick masonry work with first class bricks in
foundation and plinth including cost of all materials as
required complete:-
85.00
Cum.
NR
NR
In cement mortar 1:4 ( 1 cement : 4 fine sand ).
SUBHEAD- STEEL WORK
13 Providing structural steel work in single section fixed
with or without connecting plate including cutting,
hoisting, fixing in position and applying a priming coat of
approved steel primer all complete as required.
30.00
Sqm.
NR
NR
NR
NR
NR
NR
NR
NR
400.00
Kg.
600.00
Kg.
14 Steel work welded in built up section/framed work
including cutting, hoisting, fixing in position and applying
a priming coat of approved steel primer using steel etc.
complete as required:In grating, frames, guard bar, railing, brackets, gates
and similar works, all complete.
15 Providing 1.8 mtr height chain link fenching around substation areas with angle post 65 x 65 x 6 mm placed
every 2.5 mtr. Apart embeded in cement concrete block
of 1:3:6( 1 cement:3 river sand:6 jhama bricks aggrigate
20 mm nominal size) and every 12th post corner post to
be shurtted and embeded in cement concrete of 45 x 45
x 60 mm of same mix both post should be fitted with GI
stapple of M.S.flat of 50 x 6 mm .Two sutaible gates
made of 50 mm dia GI pipe and chain link are to be
provided within sub-station fenching (width of gate shall
be 4.00 mtr. and height 1.80 mtr. and 2nd gate of 1.20
mtr. width 1.80 mtr height.
140.00
SUBHEAD- FINISHING WORK
Page 264
Mtr.
16 12 mm cement plaster in single layer including cost of
materials required and finishing even and smooth and
curing complete.
In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
17 Neat cement punning.
18 Applying one coat of cement primer of approved brand
and manufacturer on wall surface complete.
19 Applying priming coat:
With ready mixed red oxide zinc chromate primer of
approved brand and manufacture on steel, galvanised
iron / steel work.
790.00
790.00
sqm
NR
NR
sqm
NR
NR
19.20
sqm
NR
NR
NR
NR
NR
NR
NR
NR
46.08
sqm
20 Finishing walls with acrylic smooth exterior paint of
required shade of approved brand and manufacture on
new work ( two or more coats applied @ 1.67 kg/10 sqm
) over and including base coat water proofing cement
paint applied @ 2.20 kg/10 sqm complete.
19.20
sqm
46.08
sqm
NR
NR
a) 25 mm X 10 mm.
180
Mtr.
NR
NR
b) 40 mm X 20 mm.
60
Mtr.
NR
NR
21 Finishing with epoxy paint ( two or more coats ) of
approved brand and manufacture at all locations
prepared and applied as per manufacturer's
specification on new work including appropriate priming
coat, preparation of surface etc. complete.
On steel work
SCHEDULE -F
(Internal electrification of control room building)
1
2
Supplying and fixing of PVC casing and capping
in/c. all accessories as required (Make : - Presto plast / Precision)
Supplying and drawing of PVC insulated copper
conductor cable in existing PVC casing -capping /
conduit in/c. necessary connection as required.
(Make: - Havell's / National / Plaza.)
Page 265
2
a) 2 X 1.5 Sq. mm.
400
Mtr.
NR
NR
b) 2 X 4 Sq. mm.
150
Mtr.
NR
NR
c) 2 X 6 Sq. mm.
70
Mtr.
NR
NR
a) Ceiling rose.
62
No.
NR
NR
b) Angle lamp holder.
24
No.
NR
NR
c) 5/6 Amp. piano switch.
102
No.
NR
NR
d) 5/6 Amp. socket.
16
No.
NR
NR
e) 15/16 Amp.piano switch.
8
No.
NR
NR
f) 15/16 Amp. 5 pin socket.
8
No.
NR
NR
g) Ding dong call bell.
3
No.
NR
NR
4
Supplying and fixing of 415 volt, 63 amp. TPN
main switch (Rewireable) front handle in/c. drilling
holes on wooden board and connection as
required. (Make: - Havells / HPL / Standard).
2
No.
NR
NR
5
Supplying and fixing of 6 ways metal enclosure for
240/415 Volts MCB (SP/SPN/DP/FP) complete with
necessary bus bar, earth bar, neutral link etc. including
connection as required. (Make: - Havells / HPL /
Standard).
2
No.
NR
NR
6
Supplying and fixing of 5 to 32 Amps. rating 240 Volts
'G' Series MCB of single pole in the existing MCB DB
complete with connection etc. as required. (Make: Havells / HPL / Standard).
10
No.
NR
NR
7
Providing earthing with 40 mm dia. GI perforated pipe of
4.5 mtr. long with masonary enclosure on top etc. as
required.
2
No.
NR
NR
8
Extra for using salt and charcoal for pipe earth elctrode
as required.
2
Set.
NR
NR
Supplying and fixing of accessories for PVC
casing and capping in/c. necessary connection as
required. Make: - Anchor / Precision / Cona (Nice) /
SSK / J.J. Deluxe (Fancy).
3
Page 266
Providing and fixing 8 swg GI wire on surface or in
conduit pipe for loop earthing.
20
Mtr.
NR
NR
Providing and laying earth connection from earth
10 electrode with 8 swg GI wire / copper wire in 15 mm
dia. G.I. pipe from earth electrode as required.
24
Mtr.
NR
NR
Supplying and drawing of 4 sq. mm. aluminium
11 conductor wire for loop earthing including
connection as required.
300
Mtr.
NR
NR
Supplying and fixing of single box type FTL fittings
complete with 1 no. 40 / 36 watt copper ballast, 40/36
12 watt flurosent tube, starter, holder, pf improving
capacitor etc. in/c. connection as required. (Make: Phillips / Crompton / Bajaj).
20
No.
NR
NR
Supplying and fixing of double box type T 5 rated
energy efficent FTL fittings complete with 2 nos. 40 / 36
watt copper ballast, 2 nos. 40/36 watt flurosent tube,
13
starter, holder, pf improving capacitor etc. in/c.
connection as required. (Make: - Phillips / Crompton /
Bajaj).
8
No.
NR
NR
Supplying and fixing of ceilling luminaries with 2 nos.
PLS 11 Watt lamp and mirror optics including necessary
14
connection as required. (Make: - Phillips, Cat no.-FCS 31 / 211).
2
No.
NR
NR
30
No.
NR
NR
8
No.
NR
NR
4
No.
NR
NR
6
No.
NR
NR
4
No.
NR
NR
9
Supplying and fixing of accessories for PVC
casing and capping in/c. necessary connection as
required.
a) 102 mm X 102 mm, size wooden formica board
with bakelite cover.
b) 102 mm X 178 mm, size wooden formica board
15 with bakelite cover.
c) 152 mm X 203 mm, size wooden formica board
with bakelite cover.
d) 203 mm X 300 mm, size wooden formica board
with bakelite cover.
e) 254 mm X 300 mm, size wooden formica board
with bakelite cover.
Page 267
Supplying and fixing of 300 mm sweep exhaust
16 fan including necessary connection as required.
(Make: - Crompton / Khaitan / USHA / Orient).
8
No.
NR
NR
Supplying and fixing of necessary shutter for 300
17 mm exhaust fan in the existing whole including
necessary painting etc. as required.
8
No.
NR
NR
Supplying and fixing of 1200 mm sweep ceilling fan
including fixing of regulator and wiring in down rod of
18
standard length etc. as required. (Make: - Crompton /
Khaitan / Orient / USHA).
24
No.
NR
NR
24
No.
NR
NR
19
Supplying and fixing of 18 watt CFL in the existing
angle holder. (Make: - Phillips / Bajaj / Orpat.
Page 268
1.
2.
Page 269
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1
Page 270
2
3
4
5
6
Page 271
7
8
9
10
Page 272
c
d
10
a
11
a
12
a
b
c
d
e
13
14
15
16
17
Page 273
18
19
20
21
22
23
24
25
26
27
Page 274
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
a
51
a
52
a
Page 275
53
a
54
55
56
57
58
59
60
a
61
62
Page 276
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
Page 277
82
83
84
85
86
87
88
89
90
91
92
Page 278
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
1
2
Page 279
i) 4 pole angle location 30˚ to 60˚ on 11 Mtrs. Long S.T. Pole:-3 locations.
ii) 2 pole on 11.00 mtr. long S.T pole:- 26 locations.
Page 280
ii) 2 pole on 11.00 mtr. long S.T pole:- 26 locations.
iII) Line length :-1.8 Km
Iv) Normal Span:- 50 Mtrs.
v) Conductor: ACSR DOG (7/1.57/6/4.72/4.26 mm )
vi) Stay set:=18Sets
Page 281
Page 282
Page 283
Page 284
Page 285
Page 286
Page 287
Deputy General Manager
Jirania Electrical
Division
Additional
General
Manager
Jirania: West
Tripura
Electrical
Circle
No.-IV,Agartala
Page 288
33 / 11KV
and Land
ssion line from
TOTAL
AMOUNT
(6+10+12)
13
Page 289
Page 290
Page 291
Page 292
Page 293
Page 294
Page 295
Page 296
Page 297
Page 298
Page 299
Page 300
Page 301
Page 302
Page 303
Page 304
Page 305
Page 306
Page 307
Page 308
Page 309
Page 310
Page 311
Page 312
Page 313
Page 314
Page 315
Page 316
Page 317
Page 318
Page 319
Page 320
Page 321
Page 322
Page 323
Page 324
Page 325
Page 326
Page 327
Page 328
Page 329
Page 330
Page 331
Page 332
Page 333
Page 334
Page 335
Page 336
Page 337
Page 338
Page 339
Page 340
Page 341
Page 342
Page 343
Page 344
Page 345
Page 346
Page 347
Page 348
Page 349
Page 350
Page 351
Page 352
Page 353
Page 354
Page 355
Page 356