PROJECT NAME:
OE PROJECT NO.:
Shelby CS High School
J20100329.000
SUBMITTAL NO:
Various
MANUFACTURER:
Gym Audio Equipment Data Sheets
DESCRIPTION:
SPEC SECTION:
Sub #011 2741201 Gym Audio
Equipment Data
Sheets 20130509
274120-1
DATE RECEIVED
5/9/13
DATE DUE
5/16/13
OSBORN DISTRIBUTION
Discipline
Reviewer
Review Complete Date
Action
Architectural:
Structural:
Civil:
Mechanical:
Electrical:
1100 Superior Ave., #300
441 Wolf Ledges Pkwy., #300
Cleveland, OH 44114
Akron, OH 44311
t: 216-861-2020
t: 330-535-3132
f: 216-861 3329
f: 330-535-3195
X
Technology:
AMW
Other:
1.
“px” in the check box indicates the Primary Reviewer; “x” in the check box
indicates additional Reviewer(s).
2.
The Primary Reviewer should review the submittal first.
3.
The Primary Reviewer is responsible for coordinating with the other
disciplines.
osborn-eng.com
This information is only for the general conformance with the design
concept and the information given in the Construction Documents.
Comments made on the shop drawings during this review do not relieve
the contractor from compliance with the requirements of the plans and
specifications and applicable laws, codes and regulations. Review of a
specific item shall not include review of an assembly of which the item is a
component. The Contractor is responsible for: dimensions to be confirmed
and correlated at the job site; information that pertains solely to the
fabrication processes or to the means, methods, techniques, sequences
and procedures of construction; coordination of the Work with that of all
other trades and performing Work in a safe and satisfactory matter.
REVIEWED FOR VALIDITY OF DESIGN
CRITERIA ONLY
REVIEWED (REV):
FURNISH AS NOTED (FN):
REVISE AND RESUBMIT (RR):
REJECTED (REJ):
SUBMIT SPECIFIED ITEM:
SUBMITTAL NOT REQUIRED
AND NOT REVIEWED:
REVIEWED BY: AMW
DATE: 6/10/2013
NO EXCEPTION TAKEN:
REVISE AND RESUBMIT
AS NOTED:
REVIEWED BY:
DATE:
Comments:
1. Verify that antennae are located and provided in sufficient quantity so as to provide 100% coverage.
2. Digital Mixer does not meet specification. Provide component that meets specification.
All other items except that which is indicated in item 2 above are approved for procurement. Provide submission for item
associated with item 2 above.
Page 1 of 1
Submittal Review Form - Standard
Submittal Stamp Page
PROJECT:
Shelby High School
CM / AE:
Barton Malow Company, MKC Associates & Obsorn Engineering
CONTRACTOR:
Zenith Systems LLC
Submittal Type Attached:
Architectural
X
Structural, Mechanical, Electrical
SUBMITTAL NO:
Samples
DATE:
1
ITEM(S): Gym Audio Equipment Data Sheets
SPECIFICATION SECTION(S):
Shop Drawings
QUANTITY:
27 41 20
CONTRACTOR STAMP
By Stacie Steele at 2:20 pm, May 06, 2013
CM STAMP
A/E STAMP
5/3/2013
1
PROJECT SUBMITTALS
Shelby Schools
High School Technology
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
SEC /
ITEM
27 41 20
2.2 B 1
27 41 20
2.2 B 2a
27 41 20
2.2 B 2b
27 41 20
2.2 B 2c
27 41 20
2.2 B 2c
27 41 20
2.2 B 4
27 41 20
2.2 B 4
27 41 20
2.2 B 5a
27 41 20
2.2 B 5b
27 41 20
2.2 B 6
27 41 20
2.2 B 6
27 41 20
2.2 B 6
27 41 20
2.2 B 6
27 41 20
2.2 B 6
27 41 20
2.2 B 7
27 41 20
2.2 B 8
27 41 20
2.2 B 8
27 41 20
2.2 B 8
27 41 20
2.2 B 8
27 41 20
2.2 B 9
27 41 20
2.2 B 9
27 41 20
2.2 B 9
DESCRIPTION
MNFG
PART NUMBER
CD/Ipod Player
TASCAM
CD200i
Wireless Microphone
Shure
ULXP2458
Hand Held Microphone
Shure
SM‐58S
XLR Mic Cables (25' & 50')
ProCo
AQ25 & AQ50
Mic Stand
Atlas
MS20E
Amplifier
Crown
CDi1000
Amplifier
Crown
CDi2000
Speaker Electrovoice
ZX1i90T
COLOR: BLACK
Speaker w/transformer
Electrovoice
ZX360B
COLOR: BLACK
Hearing Assist
Williams
PPA377PRO
Hearing Assist Receiver
Williams
PPAR37
Hearing Assist Neckloop
Williams
NKL001
Hearing Assist Ear Bud
Williams
EAR014
Hearing Assist Charging Base
Williams
CHG3512
Power conditioner/sequencer
Furman
PS8RII
Antenna Cable (RG‐8)
West Penn
25810
Speaker Cable
West Penn
25224B
Hearing Assist Antenna Cable
West Penn
25841
Microphone Cable
West Penn
D25454
Middle Atlantic
Middle Atlantic
Middle Atlantic
Rack
Drawer w/lock&foam
Rack Power Strip
ERK‐4425
UD4
PD915R
23
27 41 20
Processor
BSS
BLU100
24
27 41 20
Wall Controller
BSS
SW9012US
27 41 20
NOTES
ITEM 1
CD-200I SPECIFICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Plays audio CDs, MP3 CDs and WAV file CDs
Dock connector for Apple iPod charging and playback
iPod video playback from S-video or composite output
CD TEXT and ID3 tag support
Continue, Random and Program play modes
Repeat All and Repeat Single play modes
Index Search
Shock/skip prevention memory buffer
±12% pitch control (analog outputs only)
RCA unbalanced line outputs (CD and iPod)
Coaxial and Optical S/PDIF digital out (CD only)
1/4" stereo headphone output
2u rack mountable
Wireless 55-key remote control
19"W x 3.72" H x 11.73"D
9.3 lbs
ITEM 2
Wireless Microphones
ULX WIRELESS MICROPHONE SYSTEMS
SPECIFICATION SHEET
ULX STANDARD
ULX Standard UHF systems represent a breakthrough
in performance and price for both working musicians
and professional sound installers. Multiple system
configurations provide limitless options, each with a choice
of legendary Shure microphone transmitters. Over 1400
selectable, pre–programmed frequencies are available,
and Automatic Frequency Selection provides a straight
shot to a clear channel.
ULX PROFESSIONAL
Step up to ULX Professional wireless, UHF systems for
working musicians and professional sound installers.
Multiple system configurations provide limitless options,
each with a choice of legendary Shure microphones. Up
to 1400 selectable, pre–programmed frequencies are
available, and Automatic Frequency Selection provides a
straight shot to a clear channel. ULX Professional systems
offer more advanced features and controls, including
lockable settings and group scan function.
ULXS4 DIVERSITY RECEIVER
• Automatic Frequency Selection
• Over 1400 selectable frequencies
• Predictive Diversity
• RF presence LED
• 5–segment audio meter
• 3–segment transmitter battery fuel gauge
• Multi–function LCD
• 1/2 rack design
• Detachable 1/4 wave antennas
• Durable plastic chassis
• Locking DC connector on the Power Supply
• XLR and 1/4” outputs
• Mic/line switchable XLR Output
• In line DC Power on Antenna Connections
ULXP4 DIVERSITY RECEIVER
• Automatic Frequency Selection with group scan function
• Over 1400 selectable frequencies
• Predictive Diversity
• 5–segment audio meter
• 5–segment RF meter
• Advanced multi–function LCD
• Squelch adjustment
• 1/2 rack design
• In–line DC power on antenna connections
• Remotable 1/2 wave antenna
• Frequency and volume lockout
• Rugged metal chassis
• Furnished rack hardware
• Locking DC connector on the power supply
• XLR and 1/4” outputs
ULX1 AND ULX2 TRANSMITTERS
• 3–segment battery fuel gauge
• Backlit LCD shows group and channel
• Adjustable Frequency settings
• Up to 1400 selectable frequencies
• Frequency and power lockout
• 8 hour battery life
• 300 ft (92m) operating range Line of sight
• –20dB pad switch on ULX1
NOTE: Available frequencies depend on the applicable
regulations in the country where the system is
used.
ULXS4
ULX1
ULX1
©2012 Shure Incorporated
TL1025 (Rev. 4)
ULX2
ULX2
ULXP4
ULXS4
ULXP4
Printed in U.S.A.
SPECIFICATIONS
Image Rejection
80 dB typical
RF Carrier Frequency Range
Spurious Rejection
470.000 to 865.000 MHz (Available frequencies
depend on the applicable regulations in the country
where the system is used). Refer to the frequency
supplement supplied with the system.
75 dB typical
Ultimate Quieting (reference ±38 kHz deviation)
>105 dB, A-weighted
Effective Range
System Distortion (reference ±38 kHz deviation,
1 kHz modulation)
NOTE: Actual working range depends on RF signal
absorption, reflection, and interference
Power Requirements
100 m (300 ft.) under optimal conditions
0.3% total harmonic distortion, typical
ULX1, ULX2: 9V alkaline battery; 8.4 V NiMH 500 mA
optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550
mA
Audio Frequency Response
25 to 15,000 Hz, ±2 dB
NOTE: Overall system frequency response depends on the microphone element.
Battery Life
8 to 9 hours (with 9V alkaline battery)
Transmitter Audio Polarity
Operating Temperature Range
Positive pressure on microphone diaphragm (or
positive voltage applied to tip of WA302 phone plug)
produces positive voltage on pin 2 (with respect to
pin 3 of low impedance output) and the tip of the high
impedance 1/4-inch output
- 20° to 49° C (- 4° to 120° F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x
2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia.
(8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in.
x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in.
x 8.56 in. x 6.88 in.)
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (±38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line),
–17 dBV (mic)
1/4 inch connector (into 3000 ohm load): –2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50
ohms at line level; 2000 ohms at mic level
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without
battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without
battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
Modulation
±38 kHz deviation compressor-expander system with
pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 μV for 12 dB SINAD (typical)
ULX1 Bodypack Transmitter
4-PIN MINI CONNECTOR
CONDENSER MICROPHONE
BODYPACK TRANSMITTER
TA4F
TA4M
500Ω
4kΩ
+5V
500Ω
AUDIO
1kΩ
4.7 µf
300kΩ
27 pf
27 pf
100kΩ
GROUND
TA4F
INSTRUMENT CABLE
AUDIO
TIP
SLEEVE
SHIELD
2
ULX1 Transmitter Input
Microphone (pins 3
and 4 tied together)
Guitar (with WA302)
Connector
TA4M
TA4M
Configuration
Unbalanced, active
Unbalanced, active
Actual Impedance
75 kΩ
1 MΩ
Maximum Input
Level
-4 dBV (1.82 Vp-p)
Gain Switch 0 dB: 5 dBV
(5 Vp-p)
ULX2 Transmitter Input
Configuration
Unbalanced, active
Actual Impedance
20 kΩ
Maximum Input Level (1 kHz, 1% THD)
12 dBV (10 Vp‑p)
Gain Switch -20 dB:
25 dBV (50 Vp‑p)
Pin Assignments
1 = Ground
2 = +5V through
4.5 kΩ
(Microphone Bias)
3 = Audio
4 = FET active load
1
2
3
4
=
=
=
=
Ground
No Connection
Audio
No Connection
ULXP4, ULXS4 Receiver Audio Output
ULXP4, ULXS4 Receiver Antenna Input
Connector
Unbalanced (1/4 in.)
Balanced (XLR)
Actual Impedance
3 kΩ
Mic. Level: 1848 Ω
Line Level: 75 Ω
Pin Assignments
Tip = Hot
Ring/Sleeve = Ground
1 = Ground
2 = Hot
3 = Cold
Phantom Power Protection?
Yes
Yes
Furnished Accessories
Microphone Stand Adapter (ULX2)
Grip/Switch Cover (ULX2)
Zipper Bag (ULX1)
Zipper Bag (ULX2)
Screwdriver (ULX2)
95A2313
95B2313
80A498
Maximum Input Level
+6 dBm (–20 dBm recommended)
Pin Assignments
Shell = Ground, Center = Signal
Voltage for Remote
Power
12 Vdc, 150 mA maximum
AC Adapter (220 VAC, 50 Hz)
AC Adapter (230 VAC, 50/60 Hz)
AC Adapter (230 VAC, 50/60 Hz, Europlug)
RPW112
SM86 Cartridge with Grille (ULX2/SM86)
RPW114
SM87A Cartridge with Grille (ULX2/87)
BETA 87A Cartridge with Grille (ULX2/BETA 87A)
UA844SWB-E
BETA 87C Cartridge with Grille (ULX2/BETA 87C)
UA8100
Matte Silver Grille for SM86
UHF Antenna Power Distribution Amplifier (UK)
UA844SWB-UK
1.8 m (6 ft.) BNC–BNC cable (RG58)
UA806
Matte Silver Grille for BETA 58A®
UA850
Black Grille for SM87A
33 m (100 ft.) BNC–BNC cable (RG213)
7.6 m (25 ft.) BNC–BNC Cable (RG8X)
15.2 m (50 ft.) BNC–BNC Cable (RG8X)
0.6 m (2 ft.) BNC–BNC Cable (RG58)
Four Antenna Rack Panel
Front Mount Antenna Kit (Includes 2 cables and 2 bulkhead adapters)
Remote Antenna Bracket with BNC Bulkhead Adapter
Rack Mount Antenna Kit for single Receiver
Rack Mount Kit for Two Receivers
Carrying Case
Microphone Adapter Cable (XLR to TA4F)
UA825
UA802
UA440
UA600
UA505
UA506
UA507
WA610
WA310
Matte Silver Grille for SM58®
Matte Silver Grille for BETA 87A
PS41J
RPW118
RPW116
RPW120
RPW122
RK143G
RPM226
RK265G
RK312
RK214G
Black Grille for BETA 58A
RPM323G
Belt Clip
44A8013A
Black Grille for BETA 87A and BETA 87C
1/4-Wave Antenna (470 - 752 MHz)
1/4-Wave Antenna (774 - 952 MHz)
RPM324G
UA400B
UA400
1/2-Wave Antenna (638 - 698 MHz)
UA820L3
1/2-Wave Antenna (740 - 814 MHz)
UA820Q
1/2-Wave Antenna (746 - 784 MHz)
UA820E
1/2-Wave Antenna (554 - 590 MHz)
1/2-Wave Antenna (470 - 530 MHz)
1/2-Wave Antenna (572 - 596 MHz)
1/2-Wave Antenna (578 - 638 MHz)
3
PS41E
SM58® Cartridge with Grille (ULX2/58)
UA870USTV
UA844SWB
PS41AZ
PS41UK
BETA 58A® Cartridge with Grille (ULX2/BETA 58)
UHF Antenna Power Distribution Amplifier (U.S.A.)
PS41
PS41AR
AC Adapter (230 VAC, 50/60 Hz)
UA221
UA830USTV
UHF Antenna Power Distribution Amplifier (Europe)
50 Ω
–95 to –30 dBm
AC Adapter (100 VAC, 50/60 Hz)
UHF In-Line Antenna Amplifier
UHF Powered Directional Antenna
Actual Impedance
Nominal Input Level
AC Adapter (120 VAC, 60 Hz)
WA555
Passive Antenna Splitter/Combiner Kit
BNC
Replacement Parts
WA371
Optional Accessories
Connector Type
UA820D
UA820G
UA820F
UA820J
United States, Canada, Latin
America, Caribbean:
Shure Incorporated
5800 West Touhy Avenue
Niles, IL 60714-4608 USA
Phone: 847-600-2000
Fax: 847-600-1212 (USA)
Fax: 847-600-6446
Email: info@shure.com
www.shure.com
©2012 Shure Incorporated
Europe, Middle East, Africa:
Shure Europe GmbH
Jakob-Dieffenbacher-Str. 12,
75031 Eppingen, Germany
Phone: 49-7262-92490
Fax: 49-7262-9249114
Email: info@shure.de
Asia, Pacific:
Shure Asia Limited
22/F, 625 King’s Road
North Point, Island East
Hong Kong
Phone: 852-2893-4290
Fax: 852-2893-4055
Email: info@shure.com.hk
ITEM 3
Product Specifications
SM58® Cardioid Dynamic Microphone
Overview
The legendary SM58® is an industry-standard, highly versatile cardioid dynamic vocal microphone that is consistently the first choice of vocal
performers around the globe. Even in extreme conditions, the SM58 is tailored to target the main sound source while minimizing background noise,
delivering warm and clear vocal reproduction.
Features
•
•
•
•
•
•
•
•
Frequency response tailored for vocals, with brightened midrange and bass rolloff
Uniform cardioid pickup pattern isolates the main sound source and minimizes background noise
Pneumatic shock-mount system cuts down handling noise
Effective, built-in spherical wind and pop filter
Supplied with break-resistant stand adapter which rotates 180 degrees
Legendary Shure quality, ruggedness and reliability
Cardioid (unidirectional) dynamic
Frequency response: 50 to 15,000 Hz
Available Models
SM58-LC
Includes Stand Adapter and Zippered Pouch
SM58-CN
Includes 7.6 m (25 ft) XLR-Male to XLR-Female Cable, Swivel Adapter and a Zippered Pouch
SM58S
Includes Integrated On/Off Switch, Swivel Adapter and a Zippered Pouch
Specifications
Type
Frequency Response
Polar Pattern
Sensitivity
(at 1,000 Hz Open Circuit Voltage)
Impedance
Polarity
Case
Connector
Connector
Net Weight
Dimensions
Dynamic
50 to 15,000 Hz
Cardioid
–54.5 dBV/Pa (1.85 mV)
1 Pa = 94 dB SPL
Rated impedance is 150Ω (300Ω actual) for connection to microphone
inputs rated low impedance
Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3.
Dark gray, enamel-painted, die cast metal; matte-finished, silver
colored, spherical steel mesh grille
Three-pin professional audio connector (male XLR type)
Three-pin professional audio connector (male XLR type)
298 grams (10.5 oz)
162 mm (6-3/8 in.) L x 51 mm (2 in.) W
SM58
Optional Accessories and Replacement Parts
A58WS
Windscreen
A55M
Isolation Mount
C25F
7.6 m Cable (25 ft)
A25D
Microphone Clip
A26M
Dual Mount
RK143G
Screen and Grille
R59
Cartridge
S37A, S39A
Desk Stand
+20
dB
+10
0
–10
–20
125 Hz
500 Hz
1000 Hz
2000 Hz
4000 Hz
8000 Hz
Polar Pattern
www.shure.com
©2009 Shure Incorporated
20
50 100
2
3 4 5 6 7 89
1000
2
Hz
Frequency Response
3 4 5 6 7 89
10000 20000
Pro Co Sound | On Stage with the Best
Page 1 of 1
ITEM 4
Ameriquad Microphone Cable
xlrf/xlrm black/gold 24awg quad wire
Model
Description
AQ-3
MIC XF/XM 3FT LO-Z QUAD
AQ-5
MIC XF/XM 5FT LO-Z QUAD
AQ-10
MIC XF/XM 10FT LO-Z QUAD
AQ-15
MIC XF/XM 15FT LO-Z QUAD
AQ-20
MIC XF/XM 20FT LO-Z QUAD
AQ-25
MIC XF/XM 25FT LO-Z QUAD
AQ-30
MIC XF/XM 30FT LO-Z QUAD
AQ-50
MIC XF/XM 50FT LO-Z QUAD
AQ-100
MIC XF/XM 100FT LO-Z QUAD
Pro Co Ameriquad cables are the appropriate choice when you want studio reference sound quality or where high
RFI fields need to be dealt with.
The cable is a 24AWG quad cable with braided shield & custom double outer jacket with Kevlar core for added
strength and to prevent stretching. This is a studio reference cable with high quality, Black Amphenol XLR’s with gold
contacts on both ends. Ameriquad cables boast two tight-twist inner quad conductors for maximum conductivity, a
highly flexible cable construction, and terrific RFI rejection.
Pro Co Sound prides itself on the high integrity of its cables and warrants Ameriquad cables with an “any excuse,
even abuse” limited lifetime warranty against defects in workmanship and material.
http://www.procosound.com/products/catalog/show/14
12/16/2009
ITEM 5
MICROPHONE STANDS
FOR PROFESSIONAL / STUDIO USE
MS-4(E), MS-43(E)
MS-20(E), MS-25(E)
FEATURES
• Ideal for a Variety of Studio, Recording, and Performance Applications
• Receive Maximum Stability of Triangular and Oversized Bases with Edge-Concentrated
Weight Distribution
• Wearproof, 3-Piece Clutch Offers Secure, Fast, & Noise-Free Height Adjustment
• Available in Choice of Mirrored Chrome or Non-Reflective Ebony Epoxy
• Field Serviceable Parts Guarantee Long Product Life
• Made in U.S.A. to High-Quality Standards
APPLICATIONS
Depend on Atlas Sound® brand stands for years of extensive, trouble-free service on stage and
in the studio. These professional floor stands are designed to accommodate the varying functional requirements of musicians, vocalists, and presenters.
Adjust Models MS-4/MS-4E from the full 65" height down to 25" for use by children or seated
instrumentalists. Choose Models MS-20/MS-20E for indoor or outdoor presentations, performances, video/film productions, church and school use, or wherever stands providing extra stability are required. Eliminate the reflections caused by high-intensity lighting in studios by utilizing Model MS-20E which features a non-reflective ebony finish. Rely on the maximum stability of
a triangular base and the added microphone protection of an air suspension system using Models
MS-25/MS-25E for studio and stage application or wherever stands are extensively used.
MS-20E
MS-4
GENERAL DESCRIPTION
All models are quality, long-lasting stands which feature durable tubing, the Atlas Sound®
wearproof clutch, and a cast iron base. The three-piece clutch provides positive locking control
and is able to withstand years of stage and studio handling. The base features edge-concentrated weight distribution and is equipped with rubber pads to absorb shock and protect floor
surfaces. Heavy-duty, rust-resistant tubing terminates in standard 5⁄8"-27 thread suitable for microphone clamps and accessories (see reverse side). Top and bottom lock-nut rings are included for versatile and secure positioning.
MS-4 MS-4E MS43 MS43E Versatile stand adjusts from 25” to 65” to meet the needs of seated
and standing instrumentalists and performers. Model includes three-section chromed tube
assembly (MS-4/MS-3) or ebony tube (MS-4E/MS-43E) with two wearproof clutches for optimum vertical height adjustment and high stability. All models feature a low-profile cast iron base
finished in ebony. The MS-4 Series base has a diameter of 10” and weighs 6 lbs. The MS-43
Series base is 12” in diameter and weighs 8 lbs.
MS-20/MS-20E. Heavy-duty microphone stands provide extra stability, extend from 37" to 66",
and are suitable for indoor/outdoor use. Tubing is manufactured of 7⁄8" and 11⁄8" dia. cold rolled
steel. Model MS-20 features chrome tubing and an ebony finished base, whereas the entire
MS-20E assembly is finished in non-reflective ebony epoxy.
MS-25
MODEL
MS-4
MS-4E
MS43
MS43E
MS-20
MS-20E
MS-25
MS-25E
HEIGHT
SPAN
25"- 65" (64-165 cm)
25"- 65" (64-165 cm)
25"-65" (64-165 cm)
25"-65" (64-165 cm)
37"-66" (94-168 cm)
37"-66" (94-168 cm)
38"-67" (97-170 cm)
38"-67" (97-170 cm)
BASE
SIZE
10" Dia. (25 cm)
10" Dia. (25 cm)
10" Dia. (25 cm)
10" Dia. (25 cm)
12" Dia. (30 cm)
12" Dia. (30 cm)
15" Tri. (38 cm)
15" Tri. (38 cm)
TUBE
FINISH
Chrome
Ebony
Chrome
Ebony
Chrome
Ebony
Chrome
Ebony
BASE
FINISH
Ebony
Ebony
Ebony
Ebony
Ebony
Ebony
Ebony w/ Chrome Cover
Ebony w/ Chrome Cover
WEIGHT
9.5 lbs. (4.3kg)
9.5 lbs. (4.3kg)
8 lbs (3.6kg)
8 lbs (3.6kg)
14.5 lbs. (6.6kg)
14.5 lbs. (6.6kg)
18 lbs. (8.2kg)
18 lbs. (8.2kg)
ELEVEN
MS-25/MS-25E. Heavy-duty studio recording stand features an integral air suspension system
to protect sensitive microphones. Height extension up to 67" is achieved by an oversized 7⁄8"
and 11⁄8" dia. tube assembly. Triangular cast base provides maximum stability and includes
sculptured sides, ebony finish, and decorative chrome cover. Model MS-25 tube finish is
chrome and the MS-25E has an ebony tube finish.
* Stability Index (I.S.I.) Factor. Evaluates the ability of a stand/boom assembly to remain at rest when acted upon by an outside force. For full explanation, refer to SL11-1501.)
Specifications subject to change without notice
1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. / TELEPHONE: (800) 876-3333 / FAX (800) 765-3435
469
© 2001 Atlas Sound LP
Printed in U.S.A.
000501
SL11-1364
FEATURES
Steel tubing is finished in a choice
of mirrored chrome or non-reflective
ebony epoxy (E).
Anti-vibration cap absorbs incidental
vibrations and sounds.
Lock-nut ring securely positions
tubing to base.
Atlas Sound stands are threaded
5
⁄8"-27 and include a lock-nut ring for
versatile positioning of accessories.
Famous Atlas Sound clutch won't slip
under pressure. Three-piece assembly
is also field serviceable.
Bases are high-stability cast metal
equipped with shock absorbing
rubber pads.
ACCESSORIES
BOOM ATTACHMENTS
BB-28X(E)
BB-77(E)
PB11X(E)
PB15(E)
PB21X(E)
PB25
PB25X
Adj. 26 1⁄4" - 383⁄4" Length, Chrome (Ebony)
Fixed 34" Length, Fixed 3⁄4 lb. Counterweight, Chrome (Ebony)
Adj. 16 1⁄4" – 24 1⁄2" Length, Fixed 3⁄4 lb. Counterweight, Chrome (Ebony)
Fixed 34" Length, Counterweight, Fixed 3⁄4-lb. Chrome (Ebony)
Adj. 25 1⁄4" – 38 1⁄2" Length, Fixed 3⁄4 lb. Counterweight, Chrome (Ebony)
Fixed, 34 1⁄2" Length, Adj. 2 lb. Counterweight, Chrome
Adj. 32" – 51 1⁄2" Length, Adj. 2 lb. Counterweight, Chrome
GOOSENECK FLEXIBLE EXTENSIONS (.338" I.D.)
GN-6(E)
GN-13(E)
GN-19(E)
6" L, Chrome (Ebony)
13" L, Chrome (Ebony)
19" L, Chrome (Ebony)
CLIP-MOUNTING MICROPHONE ACCESSORIES
LO-2B(E)
SO-1B
SW-1B
TM-1(E)
VM-2
Lock-On / Mic Clip Disconnect, Chrome (Ebony)
Snap-On / Mic Clip Disconnect, Chrome
Gyro-Microphone Swivel, Chrome
Twin Microphone Mount, Chrome (Ebony)
Compact, Shock Isolation Accessory, Chrome (replaces VM-1)
MULTI-PURPOSE CLAMPS
CO-1B
MAC-1
Adapter & Clamp, 5⁄8" -27, Max. Opening 7⁄8", Ebony
Adapter & Clamp, 5⁄8" -27, Max. Opening 1 1⁄2", Ebony
CABLE HANGERS & TUBE EXTENSIONS FOR USE WITH COUPLING ADAPTERS
CH-1B(E)
AD-7B
AD-8B
AD-14B
AD-19B
Cable / Tambourine Hanger, Chrome (Ebony)
3" Long Tube, 5⁄8"-27 Male Thread, Chrome Plated
6" Long Tube, 5⁄8"-27 Male Thread, Chrome Plated
90° Angle Tube, 5⁄8"-27 Male & Female Thread, Chrome Plated, 4"H x 4" Ext.
90° Angle Tube, 5⁄8"-27 Male & Female Thread, Chrome Plated, 6"H x 3" Ext.
REPLACEMENT KITS FOR MS-10C AND MS-10CE
MSC
MSCE
MSC-K
MSCE-K
MSAC-K
Chrome Tube Assembly (5⁄8" - 7⁄8") with Clutch
Ebony Tube Assembly (5⁄8" - 7⁄8") with Clutch
Clutch for Chrome Stands with 7⁄8" Dia. Tubing
Clutch for Ebony Stands with 7⁄8" Dia. Tubing
Miscellaneous Parts Kit with (1) Lock Ring,
(1) Anti-Vibration Cap, and (3) Rubber Base Pads
Specifications subject to change without notice
1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. / TELEPHONE: (800) 876-3333 / FAX (800) 765-3435
© 2001 Atlas Sound LP
Printed in U.S.A.
000501
SL11-1364
ITEM 6
C D i
S E R I E S
CDi Series
he CDi Series of Crown® amplifiers are
professional tools designed and built for
installed sound applications. The series
includes four models which are identical
except for output power: CDi 1000, CDi 2000,
CDi 4000 and CDi 6000. All are rugged and
lightweight, and offer unmatched value in
their class.
CDi-Series amplifiers feature an intuitive
front-panel LCD screen to guide installers
through their configurations. CDi amplifiers
also offer onboard DSP for loudspeaker
signal processing. Other features include a
switch-mode universal power supply, useful
function indicators, proportional-speed fanassisted cooling, removable Phoenix-style
inputs, barrier strip outputs for low-Z or
70V/100V/140V loads, short-circuit protection
and more.
Your investment in a CDi-Series amplifier is
backed by Crown’s Three-Year, No-Fault, Fully
Transferable Warranty.
For more details about the Crown CDi Series,
contact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
T
CDi 1000
1 kHz
Power
Features
Accurate, uncolored sound with very low
distortion for the best in music and voice reproduction
•
Switch-mode universal power supply
•
Onboard digital signal processing includes
crossovers, EQ filters, delay, and output limiting
•
Extremely versatile; rated for 2, 4, 8 ohm loads
and 70V/100V and 140V outputs
•
All products fill 2U rack spaces and weigh under
19 pounds
•
Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
•
Barrier strip outputs for low-Z or 70V/100V/
140V loads, removable Phoenix-style inputs
•
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and
guarantees its specifications
•
•
Intuitive front-panel LCD screen for quick,
easy configuration
Specifications
Output Power: See power charts below.
Voltage Gain at 1kHz:
CDi 1000: 30.5 dB
CDi 2000: 32.9 dB
CDi 4000: 34.2 dB
CDi 6000: 37.1 dB
Frequency Response: +0/–1 dB from 20 Hz to
20 kHz at 1 watt into 4 ohms.
CDi 4000
1 kHz
Power
2 ohm Dual (per channel)
700W*
2 ohm Dual (per channel)
1,600W*
4 ohm Dual (per channel)
500W
4 ohm Dual (per channel)
1,200W
8 ohm Dual (per channel)
275W
8 ohm Dual (per channel)
650W
1,400W*
4 ohm Bridge-Mono
3,200W*
70V Dual (per channel)
500W
70V Dual (per channel)
1,000W
100V** Dual (per channel)
500W
100V** Dual (per channel)
1,000W
4 ohm Bridge-Mono
140V Bridge-Mono
**100Vp
CDi 2000
1,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
140V Bridge-Mono
**100Vp
CDi 6000
2,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
2 ohm Dual (per channel)
1,000W*
2 ohm Dual (per channel)
3,000W*
4 ohm Dual (per channel)
800W
4 ohm Dual (per channel)
2,100W
8 ohm Dual (per channel)
475W
8 ohm Dual (per channel)
1,200W
2,000W*
4 ohm Bridge-Mono
6,000W*
70V Dual (per channel)
800W
70V Dual (per channel)
2,500W
100V** Dual (per channel)
800W
100V** Dual (per channel)
2,500W
4 ohm Bridge-Mono
140V Bridge-Mono
**100Vp
1,600W
With 0.5% THD.
*With 1% THD.
140V Bridge-Mono
**100Vp
5,000W
With 0.5% THD.
*With 1% THD.
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms in Stereo mode, 4 to 16
ohms in Bridge-Mono mode. CDi 1000 A1 (100V
version) is rated for 4 to 8 ohms in Stereo mode,
8 to 16 ohms in Bridge-Mono mode.
Sensitivity:
At 8 ohm rated output:
CDi 1000: 1.4V
CDi 2000: 1.4V
CDi 4000: 1.4V
CDi 6000: 1.4V
At 4 ohm rated output:
CDi 1000: 1.3V
CDi 2000: 1.2V
CDi 4000: 1.3V
CDi 6000: 1.3V
At 2 ohm rated output:
CDi 1000: 1.1V
CDi 2000: 1.0V
CDi 4000: 1.0V
CDi 6000: 1.1V
Signal to Noise Ratio (below rated 8-ohm
power at 1 kHz): CDi 1K, 2K, 4K: 100 dB (A
weighted). CDi 6K: 103 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz
to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to
1 kHz, A-weighted.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced; 10 k ohms, unbalanced.
AC Line Voltage and Frequency Configurations
Available: 100V, 120V, 220-240V, 50/60 Hz.
AC Line Current (120VAC amplifier playing 1/8
power pink noise into 4 ohms per ch):
CDi 1000: 6.8A, CDi 2000: 8.3A, CDi 4000:
10.5A; at idle draws no more than 38 watts.
CDi 6000: 15.3A; at idle draws no more than
180 watts.
CDi 1000 | 1200W
CDi 2000 | 1225W
CDi 4000 | 1250W
CDi Series
CDi 1000, 2000, 4000 back panel
Output Connectors: 4-position barrier strip
with connectors for dual louspeakers or bridgemono loudspeaker.
HiQnet USB Connector: Type B, connects to a
HiQnet network.
HD-15 Connector: For cinema I/O compatibility
with CDi-8M System Monitor. See Figure 1.
AR
Y
CDi 6000 back panel
Protection
PR
E
LI
Input EQ: 6 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. Also adjustable
high and low shelving filters. This 8-filter EQ
section can be bypassed.
Crossover Filters: Highpass and lowpass per
channel. Butterworth 6/12/18/24 dB per octave, Linkwitz-Riley 24/48 dB per octave. Also
includes ±15 dB bandpass gain and polarity
control.
Output EQ: 8 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. This 8-filter
EQ section can NOT be bypassed. Filters are
enabled individually.
Output Limiter: Prevents clipping and protects
loudspeakers. Choice of –3, –6, or –12 dB
threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is “DSP OFF.” Fifteen
are factory-set for JBL Cinema systems. Four
are user-definable.
IN
DSP Section
Sel/Prev/Next Buttons: Three buttons near the
LCD screen are used to access menu items and
front panel lockout.
LCD Screen: Backlit liquid crystal display
shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is
present at input.
–10 Indicator: Green LED flashes when output
signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when output
signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel, turns
on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the
amplifier has been turned on and has power.
M
Maximum Input Signal: +22 dBu typical.
Operating Temperature: 0° C to 40° C at 95%
relative humidity (non-condensing).
Front Panel Controls and Indicators
Level: Detented rotary level control, one per
channel.
Power Switch: On/off switch applies AC power
to the amplifier.
CDi-Series amplifiers are protected against
shorted, open or mismatched loads; overloaded
power supplies; excessive temperature; chain
destruction phenomena; excessive output
current, and input overload damage. They also
protect loudspeakers from input/output DC,
large or dangerous DC offsets and turn-on/
turn-off transients
Construction
Chassis: Steel.
Cooling: Proportional speed fan with front-torear airflow.
Dimensions: EIA Standard 19-in. rack mount
width (EIA RS-310-B), 3.5 in. (8.9 cm) high and
12.25 in. (31.11 cm) deep behind mounting
surface. CDi 6000 is 16.2 in. (41.15 cm) deep.
Net Weight:
CDi 1K. 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
Shipping Weight:
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
Rear Panel Controls and Connectors
AC Line Connector:
CDi 1K, 2K, 4K: NEMA 5-15P (15A).
CDi 6000: NEMA 6-10P (20A)
IEC C20 (20A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced
line-level input signal.
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown amplifier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new
Crown amplifier is warranted to meet or exceed original specifications for the first three years of
ownership. During this time, if your amplifier fails, or does not perform to original specifications,
it will be repaired or replaced at our expense. About the only things not covered by this warranty
are those losses normally covered by insurance and those caused by intentional abuse. And the
coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside
of the USA, please contact your authorized Crown distributor for warranty information or call
574-294-8200.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL:574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown, Crown Audio and Macro-Tech are registered
trademarks of Crown International. Other trademarks are the
®
property of their respective owners. ©2007 Crown Audio ,
Inc. Printed in U.S.A.
5/09
139648-4
ITEM 7
C D i
S E R I E S
CDi Series
he CDi Series of Crown® amplifiers are
professional tools designed and built for
installed sound applications. The series
includes four models which are identical
except for output power: CDi 1000, CDi 2000,
CDi 4000 and CDi 6000. All are rugged and
lightweight, and offer unmatched value in
their class.
CDi-Series amplifiers feature an intuitive
front-panel LCD screen to guide installers
through their configurations. CDi amplifiers
also offer onboard DSP for loudspeaker
signal processing. Other features include a
switch-mode universal power supply, useful
function indicators, proportional-speed fanassisted cooling, removable Phoenix-style
inputs, barrier strip outputs for low-Z or
70V/100V/140V loads, short-circuit protection
and more.
Your investment in a CDi-Series amplifier is
backed by Crown’s Three-Year, No-Fault, Fully
Transferable Warranty.
For more details about the Crown CDi Series,
contact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
T
CDi 1000
1 kHz
Power
Features
Accurate, uncolored sound with very low
distortion for the best in music and voice reproduction
•
Switch-mode universal power supply
•
Onboard digital signal processing includes
crossovers, EQ filters, delay, and output limiting
•
Extremely versatile; rated for 2, 4, 8 ohm loads
and 70V/100V and 140V outputs
•
All products fill 2U rack spaces and weigh under
19 pounds
•
Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
•
Barrier strip outputs for low-Z or 70V/100V/
140V loads, removable Phoenix-style inputs
•
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and
guarantees its specifications
•
•
Intuitive front-panel LCD screen for quick,
easy configuration
Specifications
Output Power: See power charts below.
Voltage Gain at 1kHz:
CDi 1000: 30.5 dB
CDi 2000: 32.9 dB
CDi 4000: 34.2 dB
CDi 6000: 37.1 dB
Frequency Response: +0/–1 dB from 20 Hz to
20 kHz at 1 watt into 4 ohms.
CDi 4000
1 kHz
Power
2 ohm Dual (per channel)
700W*
2 ohm Dual (per channel)
1,600W*
4 ohm Dual (per channel)
500W
4 ohm Dual (per channel)
1,200W
8 ohm Dual (per channel)
275W
8 ohm Dual (per channel)
650W
1,400W*
4 ohm Bridge-Mono
3,200W*
70V Dual (per channel)
500W
70V Dual (per channel)
1,000W
100V** Dual (per channel)
500W
100V** Dual (per channel)
1,000W
4 ohm Bridge-Mono
140V Bridge-Mono
**100Vp
CDi 2000
1,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
140V Bridge-Mono
**100Vp
CDi 6000
2,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
2 ohm Dual (per channel)
1,000W*
2 ohm Dual (per channel)
3,000W*
4 ohm Dual (per channel)
800W
4 ohm Dual (per channel)
2,100W
8 ohm Dual (per channel)
475W
8 ohm Dual (per channel)
1,200W
2,000W*
4 ohm Bridge-Mono
6,000W*
70V Dual (per channel)
800W
70V Dual (per channel)
2,500W
100V** Dual (per channel)
800W
100V** Dual (per channel)
2,500W
4 ohm Bridge-Mono
140V Bridge-Mono
**100Vp
1,600W
With 0.5% THD.
*With 1% THD.
140V Bridge-Mono
**100Vp
5,000W
With 0.5% THD.
*With 1% THD.
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms in Stereo mode, 4 to 16
ohms in Bridge-Mono mode. CDi 1000 A1 (100V
version) is rated for 4 to 8 ohms in Stereo mode,
8 to 16 ohms in Bridge-Mono mode.
Sensitivity:
At 8 ohm rated output:
CDi 1000: 1.4V
CDi 2000: 1.4V
CDi 4000: 1.4V
CDi 6000: 1.4V
At 4 ohm rated output:
CDi 1000: 1.3V
CDi 2000: 1.2V
CDi 4000: 1.3V
CDi 6000: 1.3V
At 2 ohm rated output:
CDi 1000: 1.1V
CDi 2000: 1.0V
CDi 4000: 1.0V
CDi 6000: 1.1V
Signal to Noise Ratio (below rated 8-ohm
power at 1 kHz): CDi 1K, 2K, 4K: 100 dB (A
weighted). CDi 6K: 103 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz
to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to
1 kHz, A-weighted.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced; 10 k ohms, unbalanced.
AC Line Voltage and Frequency Configurations
Available: 100V, 120V, 220-240V, 50/60 Hz.
AC Line Current (120VAC amplifier playing 1/8
power pink noise into 4 ohms per ch):
CDi 1000: 6.8A, CDi 2000: 8.3A, CDi 4000:
10.5A; at idle draws no more than 38 watts.
CDi 6000: 15.3A; at idle draws no more than
180 watts.
CDi 1000 | 1200W
CDi 2000 | 1225W
CDi 4000 | 1250W
CDi Series
CDi 1000, 2000, 4000 back panel
Output Connectors: 4-position barrier strip
with connectors for dual louspeakers or bridgemono loudspeaker.
HiQnet USB Connector: Type B, connects to a
HiQnet network.
HD-15 Connector: For cinema I/O compatibility
with CDi-8M System Monitor. See Figure 1.
AR
Y
CDi 6000 back panel
Protection
PR
E
LI
Input EQ: 6 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. Also adjustable
high and low shelving filters. This 8-filter EQ
section can be bypassed.
Crossover Filters: Highpass and lowpass per
channel. Butterworth 6/12/18/24 dB per octave, Linkwitz-Riley 24/48 dB per octave. Also
includes ±15 dB bandpass gain and polarity
control.
Output EQ: 8 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. This 8-filter
EQ section can NOT be bypassed. Filters are
enabled individually.
Output Limiter: Prevents clipping and protects
loudspeakers. Choice of –3, –6, or –12 dB
threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is “DSP OFF.” Fifteen
are factory-set for JBL Cinema systems. Four
are user-definable.
IN
DSP Section
Sel/Prev/Next Buttons: Three buttons near the
LCD screen are used to access menu items and
front panel lockout.
LCD Screen: Backlit liquid crystal display
shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is
present at input.
–10 Indicator: Green LED flashes when output
signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when output
signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel, turns
on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the
amplifier has been turned on and has power.
M
Maximum Input Signal: +22 dBu typical.
Operating Temperature: 0° C to 40° C at 95%
relative humidity (non-condensing).
Front Panel Controls and Indicators
Level: Detented rotary level control, one per
channel.
Power Switch: On/off switch applies AC power
to the amplifier.
CDi-Series amplifiers are protected against
shorted, open or mismatched loads; overloaded
power supplies; excessive temperature; chain
destruction phenomena; excessive output
current, and input overload damage. They also
protect loudspeakers from input/output DC,
large or dangerous DC offsets and turn-on/
turn-off transients
Construction
Chassis: Steel.
Cooling: Proportional speed fan with front-torear airflow.
Dimensions: EIA Standard 19-in. rack mount
width (EIA RS-310-B), 3.5 in. (8.9 cm) high and
12.25 in. (31.11 cm) deep behind mounting
surface. CDi 6000 is 16.2 in. (41.15 cm) deep.
Net Weight:
CDi 1K. 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
Shipping Weight:
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
Rear Panel Controls and Connectors
AC Line Connector:
CDi 1K, 2K, 4K: NEMA 5-15P (15A).
CDi 6000: NEMA 6-10P (20A)
IEC C20 (20A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced
line-level input signal.
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown amplifier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new
Crown amplifier is warranted to meet or exceed original specifications for the first three years of
ownership. During this time, if your amplifier fails, or does not perform to original specifications,
it will be repaired or replaced at our expense. About the only things not covered by this warranty
are those losses normally covered by insurance and those caused by intentional abuse. And the
coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside
of the USA, please contact your authorized Crown distributor for warranty information or call
574-294-8200.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL:574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown, Crown Audio and Macro-Tech are registered
trademarks of Crown International. Other trademarks are the
®
property of their respective owners. ©2007 Crown Audio ,
Inc. Printed in U.S.A.
5/09
139648-4
ITEM 8
ZX1i Series
8-Inch Two-Way
Indoor/Outdoor Install
Loudspeaker System
Key Features:
•
Integrated QuickSAMTM Heavy-Duty Strong-Arm Mounting
Bracket Included
•
Indoor/Outdoor Design - Meets IEC 529, IP44 & MIL810
Environmental Specs
•
ASCTM Automatic Saturation Compensation
•
EV8L 8”Weatherized Cone High-Output LF Transducer
•
DH2005 1” Exit True Compression Driver
•
90° x 50° or 100° x 100° Coverage Patterns
•
Rotatable Horn Design
•
200W Continuous, 800W Peak Power Handling
•
High Sensitivity, 123 dB Maximum SPL
General Description:
The Electro-Voice® ZX1i is the new standard of no compromise audio performance
and versatility in an easy to install, compact sound reinforcement package.
The high-tech enclosure uses injection-molded high-impact polypropylene to make
the ZX1i extremely durable. The enclosure geometry has been engineered to
provide maximum rigidity and acoustic performance. The velocity compensated
port design overcomes the limitation of many small cabinet loudspeakers and
enables exceptional low-frequency response without vent noise.
Technical Specifications:
Freq. Response1 (-3 dB): 60 Hz - 20 kHz
Freq. Range1 (-10 dB): 48 Hz - 20 kHz
Rec. Hipass Frequency: 40 Hz
TM
ZX1i installation is incredibly simple with the included QuickSAM mounting system. The QuickSAMTM is a unique, integrated mounting bracket which is virtually
foolproof. It allows the installer to simply snap the speaker onto the bracket, then
tighten it to the desired position. For array mounting, there is an optional array
bracket kit available which allows multiple units to be mounted together for a variety
of configurations.
Axial Sensitivity1 (90°): 94 dB (1W/1m)
(100°): 92 dB (1W/1m)
Max Calculated SPL (90°): 123 dB
(100°): 121 dB
Horizontal Coverage: 90° or 100°
Vertical Coverage: 50° or 100°
Zx1i uses a special circuit that when in transformer mode the network re-configures
itself to a current actuated Hi-Pass filter at the transformer primary. It gently rolls
off the lowest frequencies to maintain a safe load on the amplifier without affecting
the higher (vocal) frequencies and the program continues without interruption. Low
frequency current is limited through the transformer eliminating low frequency
saturation. Automatic Saturation Compensation allows many speakers to be run
on a distributed line with a 50Hz Hi-Pass filter before the amplifier, regardless of the
number of speakers on the same line (the number of tapped watts cannot exceed
the amplifier rating). With the same 50Hz Hi-Pass, 10 speakers on transformers
will have the same full sound as a single speaker at 8 ohms.
Enclosure Rotation: +/-35°
Enclosure Sweep: +/-45°
Rated System Power: 200W Cont.2, 400W Prog., 800W Peak
LF Transducer: EV8L, 8 in (203mm) Driver
HF Transducer: DH2005, 1 in. (25.4mm) Exit
Compression Driver
Crossover Frequency: 1.7 kHz
Nominal Impedance: 8 Ohms
Minimum Impedance: 6 Ohms
Two coverage patterns are available; 90° x 50° coverage for longer throw and
cluster applications, 100° x 100° coverage for broad even dispersion needed in
many distributed audio applications. An added benefit is horn rotation, allowing the
ZX1i to be oriented either horizontally or vertically for complete coverage flexibility.
"T" Version Wattage Taps: 70V - 6, 12.5, 25, 50, 100, 8 Ohm bypass
100V - 12.5, 25, 50, 100, 8 Ohm bypass
Connectors: 4-Pin Phoenix Connector
Enclosure Material: High Impact Polymer
Suspension: Integrated QuickSAMTM Heavy-Duty
Strong-Arm Mounting Bracket
The ZX1i molded polymer enclosure is inherently water resistant. The addition of a
multilayer grille with hydrophobic cloth and weatherized components enable the
ZX1i to perform under many environmental conditions. An optional weatherized
input panel cover with a gland nut is available for additional protection.
The ZX1i’s long excursion, high output 8" woofer with a weatherized treated cone
delivers smooth low-frequency performance with exceptional reliability. A sophisticated crossover network integrates it with the DH2005, a 1.25” voice coil true
compression driver for maximum output with extended frequency response. Fullbandwidth overload protection is provided for reliable, long term operation without
audible effect.
Grille: Polyester Powder Coated, 18GA
Galvanized Steel
Dim (H x W x D): 451mm x 282mm x 263mm
(17.75" x 11.12" x 10.35")
Net Weight: 8.4 kg (18.5 lbs) without Transformer
10.4 kg (23.0 lbs) with Transformer
Shipping Weight: 10.2 kg (22.5 lbs) without Transformer
12.3 kg (27.0 lbs) with Transformer
1
2
Half Space Measurement.
IEC Pink Noise, 6 dB Crest Factor.
ZX1i Series Full Range Loudspeaker
ZX1i-90
ZX1i-100
Frequency Response & Impedance:
Frequency Response & Impedance:
Beamwidth:
Beamwidth:
Horizontal Off Axis Frequency Response:
Horizontal Off Axis Frequency Response:
Vertical Off Axis Frequency Response:
Vertical Off Axis Frequency Response:
Engineering Data Sheet
Horizontal 1/3 Octave
Polars, ZX1i-90:
Vertical 1/3 Octave Horizontal 1/3 Octave
Polars, ZX1i-90:
Polars, ZX1i-100:
Vertical 1/3 Octave
Polars, ZX1i-100:
Dimension Drawings:
Architectural and Engineering Specs:
The loudspeaker shall be a two-way system consisting of one 8"” (102mm) lowfrequency transducer, a 1.25" titanium diaphragm true high frequency compression
driver with rotatable horn and a frequency dividing network installed in a vented
enclosure. The network shall include a full range passive limiter for total system
protection. The high frequency compression transducer shall drive a horn to evenly
cover a pattern of either 90° by 50° or 100° by 100°. The horn shall be rotatable to
allow for horizontal or vertical mounting of the cabinet. The enclosure shall be molded
of high impact polystyrene.
The finish shall be a paintable black or white. The grille shall be zinc plated, powder
coated for corrosion resistance, and equipped with both hydrophobic cloth and acoustic
foam. The loudspeaker position shall be adjustable over a range of 100° horizontally
and 45° vertically.
Top View
The support bracket shall be low profile and integral with the enclosure. The bracket
shall allow for a quick snap fit mounting of the speaker enclosure for placement
before securing. The speaker terminals shall include a 4 pin removable phoenix style
connector to allow for signal pass through. The system shall be weather resistant to
MIL Spec 810 and IEC 529 test conditions.
The loudspeaker shall be available with a 100w transformer for 70 or 100v operation.
The speaker shall have ASCTM for protection against transformer saturation overload.
There shall also be an 8 ohm bypass position on the wattage selector switch to enable
8 ohm operation from these models.
Front View
Right View
The loudspeaker system shall meet the following performance criteria: Power handling,
200-Watts long term program using IEC268-5 shaped pink noise; Frequency response,
48 Hz – 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 94 dB at one
watt, 60 Hz – 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum.
The enclosure shall be 17.75" (451mm) high, 11.12" (282mm) wide, 10.35" (263mm)
deep. Net weight shall be 18.5 lbs (8.4 kg) for non-transformer versions and 23.0 lbs
(10.4 kg) for transformer versions.
Block Diagrams:
ZX1i (Non-Transformer) and ZX1i (With Transformer) in 8 Ohm Mode
ZX1i (With Transformer)
CAUTION
This ZX1i Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the
ZX1 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an
authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.
Performance Match
ZX1i Part Numbers
•
•
•
•
•
•
•
•
301851-001 - ZX1i-90, 90° x 50° Horn, Black Finish
301851-002 - ZX1i-90W, 90° x 50° Horn, White Finish
301851-003 - ZX1i-100, 100° x 100° Horn, Black Finish
301851-004 - ZX1i-100W, 100° x 100° Horn, White Finish
301852-001 - ZX1i-100T, 100° x 100° Horn, Black Finish, Transformer
301852-002 - ZX1i-100TW, 100° x 100° Horn, White Finish, Transformer
301852-003 - ZX1i-90T, 90° x 50° Horn, Black Finish, Transformer
301852-004 - ZX1i-90TW, 90° x 50° Horn, White Finish, Transformer
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 05/2006
Part Number 38110-470 Rev. C
• D170180
• D170261
CPS2T, 120V Power Amplifier, 2 x 600W
CPS2.8, 120V Power Amplifier, 2 x 800W
Accessories
• 301918-001
• 301955-001
AB-ZE, Array Bracket Kit for 2 or 4 ZX1i or
EVID Systems, Black
TC-ZX1i, Terminal Cover with Gland Nut
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 736-4212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
ITEM 9
ZX3-60
12-inch Two-Way Passive
60° x 60°, 600W
Loudspeaker System
Key Features:
•
•
•
•
•
•
•
•
•
•
DVX3121 12” LF Transducer with Forced Air
Cooling
ND2 2” Voice Coil, 1” Exit Neodymium
Compression Driver
60° x 60° Coverage Pattern
600W Continuous (2400W Peak) Power
Handling
High Sensitivity, 131 dB Maximum SPL
Adjustable Monitor Angle (45° or 55°)
2 Anchor Plates for Single Stud Fittings and 7 Integral Suspension Points
Available in Black or White
Passive/Biamp Selectable
Full Line of Accessories
General Description:
Technical Specifications:
The Electro-Voice Zx3 is the new standard of no compromise audio performance and versatility in a simple to use, compact package.
Freq. Response1 (-3 dB): 58 Hz - 15 kHz
Freq. Range1 (-10 dB): 48 Hz - 20 kHz
Rec. Hipass Frequency: 50 Hz
At its heart are the transducers. First is the DVX3121 high performance
low frequency transducer. EV used advanced computer aided design
techniques to create forced air, directional voice coil cooling for high
power and efficiency. Finite element analysis was used to optimize the
suspension and magnetic structure for long, linear travel to provide low
distortion and greater LF extension. These features and details, such
as forged magnetic components and special materials, provide reliability with a 500W power rating in a lightweight transducer. Next is the
ND2, a 2-inch voice coil compression driver based on neodymium motor
structure to allow for maximum output while reducing size and weight to
a minimum. Its precision phasing plug and titanium diaphragm provide
better HF performance, while the integral heatsink provides cooling for
high power output.
Axial Sensitivity1: 97 dB (1W/1m)
Max. Calculated SPL: 131 dB
Horizontal Coverage: 60°
Vertical Coverage: 60°
Power Handling (Passive): 600W Continuous, 2400W Peak
LF Power Handling (Biamp): 500W Continuous, 2000W Peak
HF Power Handling (Biamp): 40W Continuous, 160W Peak
LF Transducer: DVX3121, 12 in (305mm) Driver
HF Transducer: ND2, 1 in (25.4mm) exit Neodymium
Compression Driver
Crossover Frequency: 2 kHz
The high tech enclosure uses injection-molded high-impact polypropylene structural foam to make the Zx3 incredibly durable. The enclosure
geometry elements have been carefully designed to provide maximum
rigidity and bass response. By design the Zx3 is also a perfect solution
for stage monitors by allowing two angles (45° or 55°) without any additional accessories.
Nominal Impedance: 8 Ohms
Minimum Impedance: 6.2 Ohms
Connectors: (2) Neutrik Speakon NL4’s
Enclosure Material: Polypropylene Structural Foam
Suspension: Enclosure has locations for 4 Single-Stud
Attachment Plates and 10 Forged Steel
Eyebolts - 2 on Top, 2 on Bottom, 2 on
Side, and 1 on Rear of Enclosure
Two coverage patterns are available; 60° x 60° coverage for long-throw
and cluster applications, 90° x 50° coverage for wider coverage or shorter
distances.
The Zx3 is equipped with two anchor plates for rigging with single studfittings, along with two more possible anchor plate attachment points on
the bottom. For permanent suspension or attaching brackets, the Zx3
also has two M8 inserts on the top and bottom, two under the handle,
and one on the back of the enclosure, for a total of 7. All versions are
available in black or white.
Grille: Polyester Powder Coated, 16GA
Galvanized Steel, with Rotatable Logo
Dimensions (H x W x D): 613mm x 397mm x 362mm
(24.14” x 15.64” x 14.26”)
Net Weight: 19.8 kg (43.7 lbs)
Shipping Weight: 22.1 kg (48.6 lbs)
1
Half Space Measurement.
Zx3-60 Full Range Loudspeaker
Frequency Response & Impedance:
Horizontal Off Axis Frequency Response:
100
100
100
90
10
80
70
Sensitivity (dB)
110
Impedance (Ohms)
316
Sensitivity (dB)
110
80
Passive Mode, Half Space
Impedance
20
50
100
1000
3.16
20000
10000
90
70
20
50
100
Frequency (Hz)
-6dB Beamwidth (degrees)
20° Horizontal
10° Horizontal
30° Horizontal
1000
10000
20000
Frequency (Hz)
Beamwidth:
360
On Axis
Vertical Off Axis Frequency Response
(Up):
Horizontal
Vertical
110
100
Sensitivity (dB)
100
50
20
90
80
3.6
20
100
1000
10000
70
Frequency (Hz)
Directivity:
30
On Axis
20° Vertical Up
20000
1000
20
50
100
10° Vertical Up
30° Vertical Up
1000
Frequency (Hz)
10000
20000
Vertical Off Axis Frequency Response
(Down):
100
10
10
100
Sensitivity (dB)
20
Directivity
Factor (Q)
Directivity Index (DI), dB
110
90
80
0
20
100
1000
Frequency (Hz)
10000
1
20000
70
On Axis
20° Vertical Down
20
50
100
10° Vertical Down
30° Vertical Down
1000
Frequency (Hz)
Block Diagram (Biamp Mode):
Block Diagram (Passive Mode):
10000
20000
Engineering Data Sheet
Polar Plots (1/3 Octave):
400 Hz
500 Hz
630 Hz
800 Hz
1 KHz
1.25 KHz
2.5 KHz
3.15 KHz
4 KHz
5 KHz
6.3 KHz
8 KHz
10 KHz
12.5 KHz
16 KHz
20 KHz
1.6 KHz
Horizontal = Black
Vertical = Grey
2 KHz
Dimension Drawings:
Top View
Rear View
Right View
Front View
Left View
Bottom View
CAUTION
This Zx3 Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the
Zx3 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by
an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.
Zx3 Part Numbers
•
•
•
•
•
PRD000117-001
PRD000117-002
PRD000117-003
PRD000117-004
PRD000117-005
• PRD000117-006
• PRD000117-007
• PRD000117-008
Zx3-90B, 90° x 50° Horn, Black Finish
Zx3-90W, 90° x 50° Horn, White Finish
Zx3-60B, 60° x 60° Horn, Black Finish
Zx3-60W, 60° x 60° Horn, White Finish
Zx3-90PI-B, 90° x 50° Horn, Black Finish, Weather Resistant
Zx3-90PI-W, 90° x 50° Horn, White Finish, Weather Resistant
Zx3-60PI-B, 60° x 60° Horn, Black Finish, Weather Resistant
Zx3-60PI-W, 60° x 60° Horn, White Finish, Weather Resistant
Electro-Voice
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems
Part Number LIT000171 Rev B
11/2010
Performance Match
• 301576-001
• D170312
• D170401
Accessories
•
•
•
•
•
•
•
•
•
•
301625-001
301625-002
301634-000
301633-000
ASY000032-001
ASY000032-002
ASY000031-001
ACC000012-001
ACC000007-001
ACC000033-001
SbA760, 120V Single 15” Powered Sub, 760W
CP3000S, 120V Power Amplifier, 2 x 1100W
CP4000S, 120V Power Amplifier, 2 x 1400W
CB5-B, Array Bracket Kit (Black)
CB5-W, Array Bracket Kit (White)
EBK-3, Forged M8 Eyebolt Kit, Set of Three
SSK-1, Single-Stud Rigging Kit, Set of Three
MB3-B, Wall/Ceiling Mount Bracket (Black)
MB3-W, Wall/Ceiling Mount Bracket (White)
HDC-3, Heavy-Duty Stackable Cover (Black)
TCA-1, Truss Clamp Adapter
VSA-1, Vertical Strong-Arm Mount
HA-3, Handle Mount Adapter
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
ITEM 10
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Description:
The PPA 377 features the T35 high performance transmitter: powerful microprocessor, sleek digital
display, easy-to-use menu controls. The T35 configures itself to the appropriate setting,
taking the guesswork out of complicated audio installation. Operating up to 1000 feet, the T35 is
ideal for auditoriums, theaters or other large venues where excellent coverage area is essential.
System includes four impact-resistant PPA R37 single-channel receivers. The PPA R37 receiver will
operate up to 50 hours for long-lasting performance!
Applications:
• Churches • Schools • Auditoriums • Conference Rooms • Theaters
PPA T35 Transmitter:
Dimensions, Weight:
Color:
Rack Mount:
Power:
Temperature Range:
Operating Freqs:
Frequency Accuracy:
Deviation:
Pre-Emphasis:
RF Field Strength:
Nominal Range:
Audio Proc. Functions:
Frequency Response:
Signal-to-Noise Ratio:
8.45" (21.5 cm) W x 8.18" (20.8 cm) D x 1.72" (4.4 cm) H, 3.1 lbs (1.4 kg)
Black with white legends
One EIA rack space high, 1/2 space wide
1–2 units can be mounted in a single rack space with optional RPK 005 (single) or RPK 006
(double) Rack Mount Kits
Wall mount Class II transformer (TFP 016)
Input: 120 VAC, 60 Hz, 17 W
Output: 24 VAC, 500 mA with 3-pin Molex® plug
Approvals: UL, CSA listed
Operating:0° C to 40° C (+32° F to +104° F)
Storage:-20° C to 70° C (-4° F to +158° F)
72.1-75.9 MHz* , 17 wideband channels (selectable), 72.025-75.975 MHz, 77 narrowband channels (selectable)
±.005% stability, 0-50˚ C
Wideband: ± 75 kHz maximum. Narrowband: ± 5 kHz maximum.
Wideband: 75 µsec. Narrowband: 300 µsec
Does not exceed 80 mV/m at 3 m
Up to 1000 ft (304 m) Note: Maximum transmitter range is achieved using the ANT 005 coaxial
antenna
Reduced or Normal Compressor Gain
Compression Slope Control
High Pass and Low Pass Filter Frequency control
22 – 16000 Hz, +1, -3 dB (adjustable)
74 dB transmitted
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO AUDITORY ASSISTANCE.
T35 Front Panel:
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
1
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Audio Level Control:
Audio Level Indicators:
Power On Indicator:
Phones Output:
Audio Input:
Line Output:
LCD Menu Controls:
(Push-Button Selection)
Push-button audio level controls, adjustable to 0 to -50 dB
10 LED array that reads +9 to -18 at 3 dB intervals
Green LED indicates power on
Mono signal, 1/4" TRS stereo jack, 67 mW, maximum in 50 ohms (adjustable 0 to -40 dB)
Combination 3-pin XLR, 1/4" TRS jack
RCA jack, -10 dBV (.32 VRMS) output, impedance 100 Ω
Applications Presets (Music, Voice, Hearing Assist)
Bandwidth, Frequency, Audio Input Source (Microphone, Line, Simplex), High Pass Filter, Low Pass
Filter, Compressor Slope, Compressor Gain, RF Output Power
T35 Rear Panel:
Input Levels (Bal or Unbal):
Microphone Simplex-Mic:
Line:
Simplex Mode:
RF “Off” Timer:
Common Mode Rejection:
Total Harmonic Distortion:
Approvals:
Warranty:
Nominal (1st Amber LED)
Maximum (Input Overload LED) Absolute Maximum Ratings**
-60dBV (1 mV RMS)
-20 dBV (100 mV RMS)
+20dBV (10.0 V RMS)
-8dBV (400 mV RMS)
+16 dBV (6.3 V RMS)
+20 dB V (10.0 V RMS)
12 volts simplex power (DIN 45596) on the 3-pin XLR connector
Turns off RF signal after 1 hour of no audio activity
> 57 dB @ 1 kHz, Mic or Line
< 0.25% @ -10 dB V audio line output, 1 kHz
FCC, RoHS, WEEE
5 years, parts and labor*
**Note: Stresses above these ratings may cause permanent damage. Exposure for extended periods may degrade reliability.
*90 days on accessories.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
2
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
PPA R37 Receiver:
Dimensions:
Weight:
Color:
Battery Type:
Current Consumption:
Operating Freq.:
FM Deviation:
De-Emphasis:
LED Indicator:
Sensitivity:
Input Overload:
Frequency Response:
Signal-to-Noise Ratio:
Receiver Antenna:
Audio Output:
Output Connector:
Approvals:
Warranty:
4.1" L x 2.85" W x 1.38” D (104 mm x 72 mm x 35 mm)
4.6 oz (130 g) with batteries, 2.6 oz w/o batteries (73g)
Black
Two (2) AA non-rechargeable alkaline batteries (BAT
001), approx. 48 hours battery life, or
Two (2) AA rechargeable NiMH batteries (BAT 026), 1600
mAh, approx 30 hours battery life
Nominal 52 mA
17 channels: 72.1, 72.2, 72.3, 72.4, 72.5, 72.6, 72.7, 72.8,
72.9, 74.7, 75.3, 75.4, 75.5, 75.6, 75.7, 75.8 or 75.9 MHz*.
+75 kHz
75 µS
Power: Bright Green. Low Battery: Flashes.
2 µV at 12 dB Sinad with squelch defeated
100 mV
200 Hz to 15 kHz, ± 3 dB
65 dB at 100 µV
Integral with earphone/headphone cord
35 mW, max. 16 ohm load
3.5 mm stereo phone jack, accepts either stereo or mono
plug
FCC, Industrie Canada, RoHS, WEEE
Five years, parts and labor. 90 days on cords, earphones,
headphones, batteries and other accessories
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO “AUDITORY ASSISTANCE
FOR THE HANDICAPPED.”
This device complies to “RSS-Gen Issue 2 June 2007” for Industry Canada and FCC part
15.105(b) for the United States.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This device complies with ICES-003 class B. Test data is available from the manufacturer
on request.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
3
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Bid Specs:
The PPA T35 transmitter shall be microprocessor controlled with push button configuration. It shall have an
operating range of up to 1000 feet. It shall have 17 wideband channels operating on 72.1–75.9 MHz. It shall
have 77 narrowband channels operating on 72.025–75.975 MHz.
Front Panel:
The PPA T35 shall have a push button controlled LCD digital display. There shall be three pre-configured (selectable) application presets: Hearing Assist, Music and Voice. Configurations for Bandwidth, Frequency, Audio
Input Source (Microphone, Line, Simplex), High Pass Filter, Low Pass Filter, Compressor Slope, Compressor Gain
and RF Output Power shall be push button controlled. The audio level shall be adjustable by push button control. There shall be a 10 LED array showing audio level from +9 to -18 at 3dB intervals. The PPA T35 shall have a
1/4" phone jack with push button volume control. It shall have push button control for monitoring source
audio or transmitted audio. It shall have an input overload indicator. It shall have an “on” indicator and power
button.
Rear Panel:
The PPA T35 shall be powered by 24 VAC power supply via a 3-pin Molex® connector. It shall have a 75 ohm
F-connector antenna. It shall have an ANT 025 whip antenna on the top panel directly connected to the circuit
board. The transmitter shall have an RCA line output jack. It shall have a combination 1/4" phone/XLR audio
input jack. It shall have an RF “Off” timer that turns off RF signal after 1 hour of no audio activity.
The PPA T35 shall have FCC, be compliant with RoHS and WEEE regulations and be powered by UL and CSA
power supply. It shall have a 5-year parts and labor warranty. It shall be compatible with Williams Sound FM
equipment operating on 72-76 MHz. The transmitter shall be a Williams Sound model number PPA T35.
PPA R37 Receiver:
The PPA R37 receiver shall be encased in black, PC/ABS impact-resistant plastic with a hinged battery
door. The receiver shall be a body-pack style and include a detachable belt-clip for hands-free operation.
Receiver shall have a 3.5mm stereo/mono jack to accommodate stereo or mono low impedance earphones, headphones and neckloops. Receiver shall have a combination volume control with power
on/off rotary dial. It shall have a green LED indicating battery and system status codes. The PPA R37
shall have access to 17 wideband channels between 72-76MHz. Channel selection shall be made by pushing the seek button inside the battery compartment. Receiver shall have channel-lock capability.
Receiver shall have a slide switch inside the battery compartment to select Alkaline or rechargeable
NiMH rechargeable battery operation. It shall have charger contacts on the bottom of the receiver for
use with Williams Sound drop-in chargers CHG 3512 and CHG 3502. The PPA R37 shall operate up to 48
hrs with two AA Alkaline batteries, and up to 30 hrs with two AA NiMH rechargeable batteries (BAT
026).
Receiver shall provide a maximum out of 35mW at 16 ohms with an earbud-type earphone. The system’s
audio frequency response shall be 200Hz to 15kHz ± 3dB and the signal-to-noise ratio shall be 65dB min.
The receiver sensitivity shall be 2µV or better at 12dB Sinad with squelch defeated. The PPA R37 shall
accept up to ±75kHz FM deviation and have a 75µs de-emphasis time constant.
The PPA R37 shall have FCC, Industrie Canada approvals and be compliant with RoHS and WEEE regulations. The receiver shall be covered by a five-year parts and labor warranty, excluding earphones, headphones and batteries.
*90 days on accessories.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
4
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Contact:
Domestic Sales
Williams Sound
10300 Valley View Rd.
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
International Sales
International Sales Department
Williams Sound
10300 Valley View Rd.
Eden Prairie, MN 55344 USA
Phone: +1 952 224 7791
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
5
ITEM 11
FM
SPECIFICATION DATA
Houses of Worship • Schools • Auditoriums • Conference Rooms • Theaters
PPA R37
PPA Select™ FM Receiver
The NEW PPA Select FM receiver features easy-to-use, seekbutton channel selection with access to 17 pre-set wideband
frequencies between 72-76 MHz. Digitally synthesized for even
greater audio clarity and stability, the PPA Select also offers
channel-lock capability (to prevent accidental channel change)
and a battery-saving Sleep Mode. A versatile 3.5mm stereo/mono
jack allows for a variety of earphone and headphone options, and
is neckloop/telecoil-equipped-hearing-aid compatible. The stylish,
impact-resistant PPA Select single-channel receiver is compatible
with any Williams Sound Personal PA transmitter operating on the
72-76 MHz bandwidth. The PPA Select includes two AA alkaline
batteries for up to 50 hours of long-lasting operation.
© 2011, Williams Sound, LLC MCAT 098B
PPA Select™ FM Receiver
PPA Select™ Receiver
EARPHONE
JACK
Dimensions:
Weight:
Color:
Battery Type:
OFF
Battery Life:
ON/OFF, VOLUME
CONTROL SWITCH
"ON"/
LOW BATTERY/
FLASH CODE
INDICATOR
4.1” x 2.85” x 1.38” (104 x 72 x 35mm)
4.6oz (130g) with batteries. 2.6oz (73g) without batteries
Black
(2) AA Alkaline or 2 x AA NiMH
Two (2) AA non-rechargeable alkaline batteries (BAT 001), approx. 50 hrs
(2) AA rechargeable NiMH batteries (BAT 026), 1500 mAh, approx. 32 hrs
Current Consumption:
Temperature Range:
Channels
Operating Freq.:
52mA nominal
– 0 to 50C
17, accessed via seek button in battery compartment
72.1, 72.2, 72.3, 72.4, 72.5, 72.6, 72.7, 72.8, 72.9, 74.7, 75.3, 75.4, 75.5,
75.6, 75.7, 75.8, 75.9 MHz*
Intermediate Freq.:
75 kHz
FM Deviation:
75 kHz
De-Emphasis:
75 µS
LED Indicator:
Power: Green; Low Battery: Flashes Green
AFC Range:
Sensitivity:
Input Overload:
Frequency Response:
Modulation:
Signal-to-Noise Ratio:
Receive Antenna:
± 120 kHz
2 µV at 12 dB Sinad with squelch defeated
100 mV
200 – 15 kHz
FM, +/- 75 kHz peak deviation
65 dB min @ 100 uV
Integral with earphone/headphone cord
Audio Output:
35 mW max, peak into 16 ohms
Output Connector:
3.5 mm stereo/mono phone jack
A142
Earphone:
Auto Shut-off
Approvals:
Warranty:
Earbud-type with foam cushion, 3.5 mm plug, 32 Ω
Enters sleep mode after approx 6 mins of no RF signal
FCC, Industry Canada, RoHS, WEEE
Lifetime PLUS Limited Warranty, 90 Days on most accessories.
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO AUDITORY ASSISTANCE
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
© 2011, Williams Sound, LLC MCAT 098B
PPA Select™ FM Receiver
Bid Specs:
The PPA R37 receiver shall be encased in black, PC/ABS impactresistant plastic with a hinged battery door. The receiver shall be
a body-pack style and include a detachable belt-clip for handsfree operation. The receiver shall have a 3.5mm stereo/mono jack
to accommodate stereo or mono low impedance earphones,
headphones and neckloops. The receiver shall have a combination
volume control with power on/off rotator dial. It shall have a green
LED indicating battery and system status codes. The R37 shall
have access to 17 preset wideband channels between 72-76MHz.
Channel selection shall be made by pushing the seek button inside
the battery compartment. The receiver shall have channel-lock
capability.
The receiver shall provide a maximum out of 35mW at 16ø with
an earbud type earphone. The systems audio frequency response
shall be 200Hz to 15kHz ± 3dB and the signal to noise ratio shall
be 65dB min. The receiver sensitivity shall be 2µV or better at 12dB
Sinad with squelch defeated. The R37 shall accept up to ±75kHz
FM deviation and have a 75 µ s de-emphasis time constant.
The R37 shall have FCC, Industry Canada approvals and be
compliant with RoHS and WEEE regulations. The receiver shall be
covered by a Lifetime PLUS Limited Warranty, 90 Days on most
accessories.
This receiver model shall be the Williams Sound model PPA R37.
The receiver shall have a slide switch inside the battery
compartment to select disposable Alkaline or NiMH rechargeable
battery operation. It shall have charger contacts on the bottom of
the receiver for use with Williams Sound drop-in chargers CHG
3512 and CHG 3502. The R37 shall operate up to 50 hours with
two disposable AA Alkaline batteries and up to 32 hours with two
AA NiMH rechargeable batteries (BAT 026).
Domestic Sales
Williams Sound
10300 Valley View Rd
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
International Sales
International Sales Department
Williams Sound
10300 Valley View Rd
Eden Prairie, MN 55344 USA
Phone: +1 952 943 2252
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
800.843.3544 / info@williamssound.com / www.williamssound.com
© 2011, Williams Sound, LLC MCAT 098B
ITEM 12
ITEM 13
SPECIFICATION DATA
EAR 014
Dual mini earbud
Dual mini earbud earphone
Plug
Cord length
39 inches
Impedance
16 Ohms
Frequency Range
Max input power
5mV
Sensitivity
128dB @ 1kHz
13 mm
Replacement earpad
International Sales
International Sales Department
Williams Sound
10300 Valley View Rd
Eden Prairie, MN 55344 USA
Phone: +1 952 943 2252
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
20 - 20kHz
Driver size
Weight
Domestic Sales
Williams Sound
10300 Valley View Rd
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
3.5 mm Mono
14g
EAR 015
800.843.3544 / info@williamssound.com / www.williamssound.com
© 2011, Williams Sound, LLC MCAT 120A
ITEM 14
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Description:
This multi-unit, drop-in style charger will conveniently store and charge up to 12 Williams Sound
R35, R35-8, R863, RX22-4 receivers, or T863 transmitters over the course of a 16 hour time span. It helps
keep your products organized and saves cost on having to replace alkaline batteries.
CHG 3512, CHG 3512 PRO Multiple Battery Charger:
CHG 3512:
(charger only)
Size: 9.5”L x 7.4”W x 1.7”H (24.1 cm L x 18.8 cm W x 4.3 cm H)
Weight: 1.2 lbs (.54 kg), excluding power supply
CHG 3512 PRO:
(charger in case)
Size: 18”L x 14”W x 6.75”H (45.7 cm L x 35.5 cm W x 17.1 cm H)
Weight: 10 lbs (4.53 kg)
Color:
Power Supply Input:
Power Supply:
Charging Rate:
Black ABS
90 - 240 VAC input
TFP 037 Switching AC adapter, 5 VDC - 4A output
16 Hour Charge: 140 mA
Pulse/Maintain: 140 mA
16 hours nominal
12 Units
Individual Charging Indicators: Red LEDs. LEDs blink when batteries are charged
1 year (cables and power supply warrantied for 90 days)
CE, WEEE, RoHS
Charging specifications are based on Williams Sound Corp. rechargeable NiMH battery, BAT 026 (1400 mAh)
Charging Time:
Unit Capacity:
Indicators:
Warranty:
Approvals:
Note:
CHG 3512: Charger only
CHG 3512 PRO: Charger in case
CHG 3512
Front-Top View
CHG 3512
Rear View
CHG
WARNING: DO
NOT ATTEMPT
TO RECHARGE
DISPOSABLE BATT
ERIES!
CHG
Williams Soun
d
Williams Soun
d
CHG
Receiver or
Transmitter
CHG
Charging LED
Indicator
CHG
WARNING: DO
NOT ATTE
MPT TO RECHAR
GE DISPOSABLE
BATTERIES!
CHG
TFP 035
AC Power Connection
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
1
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Bid Specs:
The CHG 3512 shall be a 12 unit drop-in battery charger and shall charge a maximum of 24 AA size NiMH
batteries while they are installed into the Williams Sound Corp. PPA R35, PPA R35-8, R863, RX22-4 style 3V
receivers or T863 style 3V transmitter.
The charger CHG 3512 shall be microprocessor controlled and enclosed in ABS plastic measuring 9.5” L x
7.4” W x 1.7” H (24.1cm L x 18.8cm W x 4.3cm H). The CHG 3512 unit shall weigh 1.2 lbs (2.64 Kg) without
power supply, 2.9lbs (6.4 Kg) shipping weight. In the optional carry case, the charger shall weigh 10 lbs
(4.53 kg).
The charger shall be a timed charger at 16 hours, and will provide a maintain charge once the timer has
completed its charging cycle. Each bay on the charger shall have a red LED indicating charging status. The
LEDs shall be on constantly on during charging and will blink indicating when batteries are fully charged.
The charger CHG 3512 shall be powered by an external switching power supply (90-240 VAC input; 5 VDC,
4A output) via a CD barrel connector.
The charger shall have CE approval, and be compliant with RoHS and WEEE regulations.
The charger shall be the Williams Sound Corp. model CHG 3512.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
2
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Contact:
United States
Williams Sound Corp.
10321 W. 70th Street
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
Canada
Thorvin Electronics
2861 Sherwood Heights Dr. Units 36-37
Oakville, ON L6J-7K1 Canada
Ph: 800-323-6634 / 905-829-3040
FAX: 905-829-4196
Web: www.thorvinelectronics.com
South America
DPTech
SIA Trecho 3/4 Lote 335 2°. Andar
71200-030 Brasília, DF
BRAZIL
Phone: (5561) 361-1384
Fax: (5561) 361-0948
Web: www.dptech.com.br
Email: ws@dptech.com.br
United Kingdom
Sound Associates
Keeble House, 81 Island Farm Road
West Molesey, Surrey KT 2SA
United Kingdom
Phone: (44) 020 8939 5900
Fax: (44) 020 8939 5901
Web: www.soundassociates.co.uk
Email: jmurdoch@soundassociates.com
Asia, Europe, Australia, Latin America, Middle East, South Africa
International Sales Department
Williams Sound Corp.
10321 W. 70th Street
Eden Prairie, MN 55344 USA
Phone: +1 952 224 7791
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
3
ITEM 15
DATASHEET
PS-8R II
POWER CONDITIONER/SEQUENCER WITH SMP+ TECHNOLOGY
UNPARALLELED POWER PURIFICATION AND PROTECTION
FEATURES
• Series Multi-Stage Protection Plus ( SMP+) for virtually maintenance free protection from surges and spikes. No sacrificed parts, no service calls, no downtime!
• Furman’s unequaled Linear Filtering Technology ( LiFT) rids systems of AC line noise for consistent audio/video clarity
• Automatic Extreme Voltage Shutdown ( E.V.S.) powers down equipment during a prolonged or extreme over-voltage
• Six sequenced rear panel outlets (in 3 groups), two switched rear panel outlets, and one front panel unswitched outlet
• Momentary and Maintained sequencing via rear panel terminal block or front panel switch
• BNC connector on the rear panel allows attachment of any standard 12V gooseneck lamp to illuminate the rear of your rack
• 15 amp rating
• 3 year limited warranty
DESCRIPTION
The most widely recognized and trusted name in AC power
conditioning is proud to introduce the PS-8R II power
conditioner / sequencer, featuring Furman’s revolutionary
SMP+ technology. Furman’s Series Multi-Stage Protection
Plus (SMP+) circuit features our exclusive Linear Filtering
Technology (LiFT) and Extreme Voltage Shutdown (E.V.S.).
Together, these technologies comprise what is, without question,
the world’s most advanced and comprehensive transient voltage
surge suppressor.
Additionally, the PS-8R II Power Conditioner/Sequencer is
capable of powering up a rack full of equipment in a 3-step
delayed sequence. The sequence is reversed for power-down. The
sequence can be initiated with either momentary or maintained
switches, locally or remotely. A duplex outlet is provided for
each delay step. A front panel screwdriver adjustment sets the
delay time for the PS-8R II. The PS-8R II also features a locking
switch with a removable key for maximum security. One or
more Furman PS-8R II’s may be installed in remote locations and
operated via low-voltage wiring. The PS-8R II includes a rear
mounted BNC jack which accepts any standard (12VAC, 0.5A)
gooseneck lamp for rear rack illumination, as well as a front panel
switch which controls the gooseneck’s operation.
PS-REL Relay Accessory
Allows a PS-8R II to be turned on by sensing AC at a
preamp’s switched outlet; also allows daisy-chaining for
6 or more delayed outlet groups.
Export Models
Models PS-8R E II: “E” suffix versions are for use in countries
with 220/240 volt AC lines. Furman Power Sequencers use
internationally accepted IEC-320 connectors.
(Continued on reverse)
PS-8R II
Series Multi-Stage Protection Plus (SMP+)
SMP+ is Furman’s proprietary surge suppression and noise
filtration system. Designed over a period of two years by our
California based engineering team, SMP+ is composed of
three separate and distinct technologies which work together
in a precisely tuned circuit to filter or “clean” the incoming
power and to protect connected equipment from potentially
damaging AC events. These technologies are Linear Filtering,
Series Multi-Stage Protection, and Extreme Voltage Shutdown.
Linear Filtering Technology (LiFT):
Unfortunately, traditional AC filter conditioners have been
designed for unrealistic laboratory conditions. Prior technologies
could actually harm audio and video performance more than
they help, due to the resonant peaking of their antiquated, nonlinear designs. Under certain conditions, these designs can
actually add more than 10 dB of noise to the incoming AC line!
Worse still, lost digital data, the need to re-boot digital pre-sets, or
destroyed digital converters are frequently caused by excessive
voltage spikes and AC noise contaminating the equipment ground.
Furman’s LiFT takes another approach, ensuring optimal
performance through linear filtering and no leakage to ground.
PS-8R II SPECIFICATIONS
Current Rating
15 amps (“E” version 10 amps)
Operating Voltage
90 to 140 VAC (“E” version 180 to 280 VAC)
Over Voltage Shutdown
140 VAC typically (“E” version 280 VAC typically)
Spike Protection Modes
Line to neutral, zero ground leakage
Spike Clamping Voltage
188 Vpk @ 3,000 amps, 133 VAC RMS
(tested to UL-1449 6,000 Vpk @ 3,000 amps)
Response Time
1 nanosecond
Maximum Surge Current
Series Multi-Stage Protection (SMP):
Traditional surge suppression relies on circuits that “sacrifice”
themselves when exposed to multiple transient voltage spikes,
requiring the dismantling of your system and repair of your surge
suppressor. With Furman’s SMP+, however, damaging transient
voltages are safely absorbed, clamped and dissipated. No sacrificed
parts, no service calls, no downtime. Also unique to Furman’s
SMP+ is its unparalleled clamping voltage. While other designs
offer clamping voltages that are well above 300Vpk, Furman’s
SMP+ clamps at 188Vpk, 133 VAC RMS, even when tested with
multiple 6000Vpk - 3000 amp surges! This unprecedented level
of protection is only available with Furman’s SMP+ technology.
Extreme Voltage Shutdown (E.V.S.):
When voltage rises to extreme levels because of a lost neutral
line or an accidental connection to 208 or 240 VAC, Furman’s
Extreme Voltage Shutdown kicks in, automatically powering down
all equipment quickly and safely in order to prevent damage
from occurring. An indicator LED will then illuminate, alerting
you to the situation until the over voltage condition is corrected.
Noise Attenuation
10 dB @ 10 kHz
40 dB @ 100 kHz
100 dB @ 10 MHz
Linear attenuation curve from 0.05 - 100 ohms line impedance
Dimensions
19” W x 10.5” D x 1.75” H
Weight
11 lbs (5 kg)
Power Consumption
6 watts
Safety Agency Listings
CE, NRTL-C
Patent Number
CA1332074 (4,901,183)
Three Year Limited Warranty
The PS-8R II is protected by a limited three year warranty
covering defects in materials and workmanship.
6,500 amps
Fu r m a n S o u n d, L LC • 1690 Cor porate Circle • Petaluma, C A. 94954 USA • Phone: (707) 763-1010 • Fax: (707) 763-1310 • w w w.Fur ma n S o u n d. co m
© 2006 Furman Sound, LLC. All rights reserved. 051006
ITEM 16
Technical Data Sheet
RG8/U Coaxial 50 Ohm - Plenum
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25810
DESCRIPTION:
RG8/U – 1 Conductor 12 AWG 7x20, 95% Bare copper braid and an overall Copolymer Jacket.
NEC RATING:
CMP
APPROVALS:
(UL) C(UL) Listed
APPLICATION:
Indoor Plenum for: 50 Systems
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Jacket Material
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
12 AWG Bare Copper
7x20
Foam FEP
.280” Nom.
1 Center Conductor
95% Bare Copper Braid
Copolymer- Solef
0.352'' Nom.
98 Lbs/1M' Nom.
NFPA 262 Plenum
Electrical & Environmental Properties:
Temperature Rating
Max.Capacitance Between Conductors @ 1 KHz
Velocity of Propagation
Impedance
DC Resistance per Conductor @ 20deg C
Jacket Color
RoHS Compliant
-40deg C to 75deg C
28.5 pf/ft Nom.
66% Nom.
52 ohms Nom.
1.6 Ohms/1M' Nom.
Natural
--
Mhz
1
10
50
100
400
700
900
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
183 lbs.
3.5”
Connectors and Accessories
50 Ohm 3 pc. BNC
CN-25810KBNC
Specification Issue Date: 10/11
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
db/100ft
.2
.6
1.3
1.9
4.1
5.9
6.9
ITEM 17
Technical Data Sheet
Plenum Communication Cables
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25224B
DESCRIPTION:
18/2 Stranded bare copper conductors, unshielded with an overall jacket.
NEC RATING:
CMP, NEC Article 800
APPROVALS:
(UL) C(UL) Listed or c(ETL)us Listed
APPLICATION:
Indoor within ducts, plenums, and other spaces used for environmental air for (Intercom Systems,
Security Systems, Sound, Audio, Background Music)
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Drain
Jacket Material
Jacket Thickness
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
18 AWG Bare Copper
7x26
Polymer Alloy
0.010'' Nom.
2
None
None
Flexible Plenum
0.015'' Nom.
0.138'' Nom.
17 Lbs/1M' Nom.
NFPA 262 Flame Test
Electrical & Environmental Properties:
Temperature Rating
Operating Voltage
Max.Capacitance Between Conductors @ 1 KHz
DC Resistance per Conductor @ 20deg C
Insulation Colors
Jacket Color
RoHS Compliant
-10°C To +60°C
300 V RMS
30 pf/ft Nom.
6.2 Ohms/1M' Nom.
Black, Red
Gray, Black, Blue, Green, Yellow
Yes
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
42 lbs
1.4”
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
The information contained herein is considered
. Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Cold Environment Precautions: Due to the nature of
PVC Compounds to become non-pliable when stored
or handled in ambient temperatures of 32 deg. F or
less, we recommend the following:
“Prior to installation, condition the cable for at
least 24 hours at room temperature to provide the
best flex properties for ease of installation.”
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
ITEM 18
Technical Data Sheet
RG6/U Type CATV Coaxial Cable Plenum
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25841
DESCRIPTION:
RG6/U – 1 Conductor 18 AWG Solid, 100% Al. Foil + 77% Al. Braid and an overall Plenum
PVC Jacket.
NEC RATING:
CATVP/ CMP
APPROVALS:
(UL) C(UL) Listed or c(ETL)us Listed
APPLICATION:
Indoor for Plenum:– CATV/MATV
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Jacket Material
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
18 AWG Bare Copper
Solid
Foam FEP
.170” Nom.
1 Center Conductor
100% Al Foil + 77% Al. Braid
Flexible Plenum PVC
0.235'' Nom.
26 Lbs/1M' Nom.
NFPA 262
Electrical & Environmental Properties:
Temperature Rating
Max.Capacitance Between Conductors @ 1 KHz
Velocity of Propagation
Impedance
DC Resistance per Conductor @ 20deg C
Jacket Color
RoHS Compliant
-20deg C to 60deg C
16.2 pf/ft Nom.
82% Nom.
75 ohms Nom.
6.5 Ohms/1M' Nom.
Ivory
Yes
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
Connectors and Accessories
F Crimp:
F Compression:
91 lbs.
2.4”
Mhz
5
55
100
270
400
550
750
1000
2000
2250
3000
CN-56TFE
CN-FS6PL2
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
db/100ft
.50
1.6
2.0
2.9
4.5
4.9
6.6
8.0
12.3
13.36
15.42
ITEM 19
Technical Data Sheet
Plenum Miniature Line-Level Audio Cable
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
D25454
DESCRIPTION:
22/2 Stranded tinned copper conductors, bonded shielded with an overall jacket.
NEC RATING:
CMP, NEC Article 800
APPROVALS:
(UL) Listed
APPLICATION:
Indoor Plenum for: Post Production Facilities, Recording Studio, Sound, Audio.
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Drain
Jacket Material
Jacket Thickness
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
22 AWG Tinned Copper
7x30
FEP- Teflon
0.007'' Nom.
2 (1 Pair)
100% Aluminum Polyester Foil-bonded
Stranded Tinned Copper
Plenum PVC
0.018'' Nom.
0.130'' Nom.
16 Lbs/1M' Nom.
UL NFPA-262
Color Code Chart
Electrical & Environmental Properties:
Temperature Rating
Operating Voltage
Max.Capacitance Between Conductors @ 1 KHz
Capacitance Between Conductors to Shield @ 1 KHz
DC Resistance per Conductor @ 20deg C
Insulation Colors
Jacket Color
RoHS Compliant
-20deg C to 60deg C
300 V RMS
35 pf/ft Nom.
67 pf/ft Nom.
17 Ohms/1M' Nom.
1. Black, 2. Red
See Chart
--
1.Black
2.Red
3.Gray
4.Blue
5.Brown
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
33 lbs.
1.3”
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
ITEM 20
96-038 / rev 11c / 06-01-10
ERK Series Enclosure
®
Middle Atlantic Products
EIA/TIA Compliant
SEISMIC CERTIFIED
EXCEPTIONAL SUPPORT & PROTECTION™
The ERK Series 19” welded stand-alone / gangable enclosures.
Advanced manufacturing techniques provide highest quality
and lowest price.
Features
• Fully welded construction
• 2,500 lb. weight capacity
• 1/8" thick structural steel internal braces
• UL Listed in the US and Canada
• Seismic certified (when used with ERK-Z4 option) with an Ip value of 1.5
• 22” OD width, available 20” or 25” OD depth
• 1/2" , 3/4", 1” & 1-1/2" electrical knockouts on removable split rear plates top and bottom,
easily removable for cable pass-through. Top plates additionally include UHF / VHF knockouts
• Standard front, optional rear 11-gauge 10-32 threaded, fully adjustable rackrail with
numbered rackspace increments
• Keylocked solid rear door standard, optional vented rear doors available
• Optional front doors available
• Configurable top options on 44, 40, and 35 space sizes
ERK-4425
• Durable black textured powder coat finish
Architects’ and Engineers’ Specifications
OPTIONS
• Front doors shall be reinforced 16-gauge steel, model #FD-XX (solid), VFD-XX
(vented, 22% open area), LVFD-xx (vented 63% open area-not available for 27
space rack) PVFD-44 (vented plexi), (X=# of rackspaces of ERK rack)
• Vented rear doors shall be 16-gauge steel & available as model #ERK-VRD-XX,
(X=# of rackspaces of ERK rack)
• Top panels for 35, 40 or 44 space ERK, 16-gauge steel, multiple styles available
including model #ERK-ST (solid), ERK-10FT (10” fan), ERK-6FT (two 6” fans)
ERK-4FT (three 4-1/2” fans), ERK-VT (vented) and ERK-LVT (large perf vented)
see A&E spec 96-01063 for more details
• Caster base, four casters shall have a total weight capacity of 1300 pounds, model
# CBS-ERK-YY (Y= cabinet depth)
• Rear rail kit, 11-gauge, 10-32 threaded, sold in pairs, hardware included, model
#ERK-RRXX (X=# of rackspaces)
• Seismic compliancy floor anchor kit, model # ERK-Z4
• 18, 21 and 27 space ERK come preconfigured with solid top that includes knockouts
to accommodate up to two 4-1/2” fans, or included vent panels
• Grommet for 4” electrical knockout in side of ERK shall be model # GK4
and include 4 pieces
• Gland grommet for 4” electrical knockout in side of ERK shall be model #GK-4G. 4 Pieces.
• Slide out option available (See AXS Spec sheet 96-055S)
C U S T O M I Z A B L E S P E C I F I C AT I O N C L I P S AVA I L A B L E AT M I D D L E AT L A N T I C . C O M
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-038 / rev 11c / 06-01-10 / ERK Series Enclosure
EIA compliant 19” stand-alone / gangable equipment rack shall be Middle Atlantic Products model #
ERK-__-__(see chart for available models). Overall dimensions of rack shall be __”H x __”W x
__”D (refer to chart). Useable height shall be __ rackspaces, useable depth shall be __” (refer to
chart). Rack shall be of fully welded construction. Weight capacity shall be 2,500 lbs. Rack shall be
constructed of the following materials: top and bottom shall be 16-gauge steel, horizontal braces shall
be 16-gauge steel welded to integral structural side panels of 16-gauge steel giving an 1/8” thick
structure, rear door shall be 18-gauge steel, all structural elements shall be finished in a durable black
powder coat. Rack shall come equipped with one pair of fully adjustable 11-gauge steel rackrail with
tapped 10-32 mounting holes in universal EIA spacing, black e-coat finish and numbered rackspaces.
Rack shall include solid locking rear door standard and solid side panels with vertical slotted vent pattern
at top and bottom (and laser knockouts for cable pass-through on 44, 40, and 35 space models). Top
and bottom of rack shall feature vertical slotted vent pattern. Rack shall have removable split rear
knockout panels with 1/2”, 3/4”, 1”, and 1-1/2” electrical knockouts installed in base and a
removable rear knockout panel with 1/2”, 3/4”, 1”, and 1-1/2” electrical knockouts and BNC
knockouts for UHF/VHF antennae installed in top. Grounding and bonding stud shall be 1/4-20
threaded, installed in base of enclosure. ERK series racks shall satisfy the 1997 UBC and 2001 CBC
Seismic Zone 4 and the 2000 IBC, 2003 IBC, 2002 ASCE Standard 7 and 2003 NFPA 5000 Seismic Use
Group III lateral force requirements for protecting 600 lbs. of essential equipment in upper floor
installations when used in conjunction with the ERK-Z4 floor anchor brackets. Rack shall be UL Listed in
the US and Canada. Rack shall be GREENGUARD Indoor Air Quality Certified for Children and Schools.
Rack shall be RoHS EU Directive 2002/95/EC compliant. Rack shall be manufactured by an ISO 9001
and ISO 14001 registered company. Rack shall be warrantied to be free from defects in material or
workmanship under normal use and conditions for the lifetime of the product.
ERK Configured A/V Enclosure
®
EIA/TIA Compliant
SEISMIC CERTIFIED
Configured A/V enclosure ships complete with the
most commonly used accessories
Includes
• Integrated fan top
• Configurable rear door with bottom vent, solid locking front door
• 3-1/4” wide vertical lacer strip (height varies based on model)
• Six horizontal lacer bars
• Twelve 8” Velcro® cable management straps
• Thin power strip, 20 Amp, 20 outlet with cord (44 space enclosures)
or 2 qty. thin power strip, 20 Amp, 10 outlet with cord (35 & 40 space
enclosures)
• Leveling feet
• 100 qty. 10-32 mounting hardware
25 ”
ERK-4425-AV
Architects’ and Engineers’ Specifications
EIA compliant 19” stand-alone equipment rack shall be Middle Atlantic Products model # ERK-__-AV
knockouts for UHF/VHF antennae. ERK Series enclosures shall satisfy the 1997 UBC and 2001
(refer to chart). Overall dimensions of rack shall be __" H x 22" W x 25" D. Useable height shall be __
CBC Seismic Zone 4 and the 2000 IBC, 2003 IBC, 2002 ASCE Standard 7 and 2003 Ed. NFPA
rackspaces, useable depth shall be 23-1/2". Fully welded construction shall provide a 2,500 lb. weight
5000 Seismic Use Group III lateral force requirements for protecting 600 lbs. of essential
capacity. Rack shall be constructed of the following materials: top and bottom shall be 16-gauge steel,
equipment in upper floor installations when used in conjunction with the ERK-Z4 seismic floor
horizontal braces shall be 16-gauge steel welded to integral structural side panels of 16-gauge steel
anchor brackets with an Ip value of 1.5. ERK-__-AV shall include a high-density thin power
giving an 1/8" thick structure. Solid front door shall be 18-gauge steel and rear door shall be 18-gauge
distribution and shall be Middle Atlantic Products model # PDT-____-NS with __ outlets and
steel and all structural elements shall be finished in a durable black powder coat. Rack shall come
20 amps (refer to chart). Thin power distribution shall be ____” long (refer to chart) x 1” deep
equipped with one pair of 11-gauge steel rackrail with tapped 10-32 mounting holes in universal EIA
x 1.9” wide. J-Box shall be 2” deep x 2” wide. Thin power distribution shall feature __ NEMA
spacing, black e-coat finish and numbered rackspaces. Rack shall include 100 qty. 10-32 mounting
5-20R outlets. Corded power strip includes 20 amp protection and mounting hardware. Corded
screws. Rack shall be equipped with one 3-1/4” vertical lacer strip Middle Atlantic Products model #
model shall beterminated with 10-foot power cord and a NEMA 5-20P plug. PDT Series shall
LACE-__-OP (refer to chart), four ‘L’ shaped straight and two 4” offset horizontal lacer bars and twelve,
feature a black anodized finish. ERK and PDT Series shall be UL Listed in the US and Canada.
8” Velcro® straps for cable management. The ERK shall have a solid locking rear door standard and
ERK-__-AV shall be GREENGUARD Indoor Air Quality Certified for Children and Schools. ERK-__-
solid side panels with vertical slotted vent pattern at top and bottom with laser knockouts for cable
AV shall be RoHS EU Directive 2002/95/EC compliant. ERK-__-AV shall be manufactured by an
pass-through. Top and bottom of rack shall feature vertical slotted vent pattern. Rack shall have feature
ISO 9001 and ISO 14001 registered company. PDT series shall be warrantied to be free from
integrated fan top, Middle Atlantic Products model # ERK-4FT-285CFM for active thermal management.
defects in materials or workmanship for a period of 3 years. ERK enclosure shall be warrantied
The ERK-4FT-285CFM shall consist of three 4-1/2” fans and airflow shall be 285 CFM. Rack shall have
to be free from defects in material or workmanship under normal use and conditions for the
removable split rear knockout panels with 1/2”, 3/4”, 1” and 1-1/2” electrical knockouts and top BNC
lifetime of the rack.
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
2.13
[54]
REAR VIEW, TOP & BOTTOM
E
laser knockouts
for 4” electrical
tubing on
ERK-35, 40 &44
Four 11/32” dia.
laser knockouts
for ganging on
ERK-35, 40 &44
8.41
[213]
A
12.38
[314]
1” [25] & 1-1/2” [38] EKO
1.50 [38]
removable EKO plates
20.00
[508]
3.50
[89]
6.00
[152]
12.00
[305]
Laser knockouts
for 4-1/2” fans
REAR
BOTTOM VIEW
mounting holes
ERK-XX20=10.41 [264]
ERK-XX25=15.41 [391]
2.00 [51]
typical front
22.00 [559]
B
19.25
[489]
REAR VIEW SIDE VIEW FRONT VIEW
5/8” [16] dia. KO
1/2” [13] dia. “D” KO
(UHF/VHF Antenna KO)
1/2” [13] & 3/4” [19] EKO
1” [25] & 1-1/2” [38] EKO
ERK basic dimensions
5.94 [151]
.78 [20]
1.50 [38]
3.44 [87]
1.50 [38]
22.00
[559]
TOP VIEW OF ERK SIDE
SECTIONAL VIEW
C
1.50 [38]
9.80 [249]
1/4 - 20 X 1”
[25] grounding and
bonding stud
(1 place only)
EKO’s
1/2” [13] &
3/4” [19]
1” [25] &
1-1/2” [38]
3.00 [76]
typical rear
fully adjustable
10-32 threaded
rackrail
front door clearance
(with rackrail in
forward-most position)
1.44 [37] solid/vented door
1.25 [32] plexi door
D
BOTTOM VIEW
All dimensions in inches unless otherwise noted [All dimensions in brackets are in millimeters]
22.00
[557]
TOP VIEW
ERK-35XX
ERK-40XX
ERK-44XX
TOP VIEW
ERK-18XX
ERK-21XX
ERK-27XX
Middle Atlantic Products
19.50
[495]
FRONT
0.41 [10] (4 places)
4.80 [122]
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
Part #
ERK-4425
ERK-4025
ERK-3525
ERK-2725
ERK-2125
ERK-1825
ERK-4420
ERK-4020
ERK-3520
ERK-2720
ERK-2120
ERK-1820
ERK-4425-AV
ERK-4025-AV
ERK-3525-AV
A
Overall
Height
81.125 [2061]
74.125 [1883]
65.375 [1661]
51.375 [1305]
40.875 [1038]
35.625 [905]
81.125 [2061]
74.125 [1883]
65.375 [1661]
51.375 [1305]
40.875 [1038]
35.625 [905]
81.125 [2061]
74.125 [1883]
65.375 [1661]
B
Useable
Height
77.125 [1959]
70.125 [1781]
61.375 [1559]
47.375 [1203]
36.875 [937]
31.625 [803]
77.125 [1959]
70.125 [1781]
61.375 [1559]
47.375 [1203]
36.875 [937]
31.625 [803]
77.125 [1959]
70.125 [1781]
61.375 [1559]
C
Rear
Height
75.125 [1908]
68.125 [1703]
59.375 [1508]
45.375 [1153]
34.875 [886]
29.625 [752]
75.125 [1908]
68.125 [1703]
59.375 [1508]
45.375 [1153]
34.875 [886]
29.625 [752]
75.125 [1908]
68.125 [1703]
59.375 [1508]
D
Overall
Depth
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
25.00 [635]
25.00 [635]
25.00 [635]
E
Bottom Opening
Depth
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
20.25 [514]
20.25 [514]
20.25 [514]
TOP OPTIONS
ERK-10FT
accepts 10” fan
ERK-6FT
accepts two 6” fans
ERK-4FT accepts
three 4-1/2” fans
ERK-10FT- 550CFM
includes 10” fan
ERK-6FT- 440CFM
includes two 6” fans
ERK-4FT- 285CFM
includes three
4-1/2” fans
(included in A/V
enclosures)
ERK-10FT-FC
includes 10” fan and
fan controller
ERK-4QFT-FC
includes 4-1/2”
quiet fans and fan
controller
ERK-ST
solid
Rack Part #
ERK-4025-AV /
ERK-3525-AV
ERK-4425-AV
ERK-VT
slot vent
ERK-LVT
large perf vent
ERK A/V Enclosure Power Distribution
Terminated
Circuit
Outlets
Part #
Overall Length
Qty
PDT-1020C-NS
5-20P
20 Amp
10, 5-20R
37.75 [959]
2
PDT-2020C-NS
5-20P
20 Amp
20, 5-20R
72.75 [1848]
1
Part #
ERK-4425-AV
ERK-4025-AV
ERK-3525-AV
ERK A/V Enclosure Vertical Lacer Bar Chart
Lacer Bar
Number of Rackspaces
LACE-44-OP
44
LACE-40-OP
40
LACE-37-OP
37
Width
3.25 [83]
3.25 [83]
3.25 [83]
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
ITEM 21
96-01105 / rev. 1b / 08-23-10
UD Series Utility Drawers
EIA/TIA Compliant
EXCEPTIONAL SUPPORT & PROTECTION™
The UD Series rackmount utility drawers offer an economical
storage solution for any enclosure
Features
• Full extension ball bearing slides extend a full 14”
UD1 shown as
a writing surface
• Durable black powder coat finish
• Keylock and latch option for security, user-installed
(2, 3 and 4 space drawers only)
• Cable entry point at the rear of the drawer allows
for optimized cable management
• Four sizes available
UD1
• UL Listed in the US and Canada
Architects and Engineers’ Specifications
EIA compliant 19” rackmount drawer shall be Middle Atlantic Products model # UD_
(refer to chart). Drawer shall have useable width of __”, a useable surface of __” and
occupy __ rackspaces (refer to chart). Drawer base shall be __-gauge steel, top and
sides shall be __-gauge steel (refer to chart). Drawer faceplate shall be __-gauge steel
with a black powder coat finish (refer to chart). Drawer shall extend __” (refer to chart).
Drawer shall use full extension, ball bearing slides. UD__ shall have cable entry point
at the rear of the drawer. UD__ shall have a knockout on the face of the drawer to
accommodate optional user-installed latch and keylock (refer to chart). Drawer shall have
mounting hole spacing of __” (refer to chart). Drawer shall have a 50 lb. weight capacity.
Drawer shall be UL Listed in the US and Canada. Drawer shall be GREENGUARD Indoor Air
Quality Certified for Children and Schools. Drawer shall be RoHS EU Directive 2002/95/
EC compliant. Drawer shall be manufactured by an ISO 9001 and ISO 14001 registered
company. Drawer shall be warrantied to be free from defects in materials or workmanship
under normal use and conditions for a period of three years.
Options
• User installed latch for UD Series drawers shall be Middle Atlantic Products model
# LATCH. LATCH shall fit 2, 3 and 4 space drawers.
• User installed keylock for UD Series drawers shall be Middle Atlantic Products model
# KYLK. KYLK shall fit 2, 3 and 4 space drawers.
• Additional set of keys for KYLK shall be Middle Atlantic Products model # ACC-KEY.
• No-slip drawer mat for UD Series drawers shall be Middle Atlantic Products
model #DM.
c u s t o m i z a b l e s p e c i f i c at i o n c l i p s ava i l a b l e at m i d d l e at l a n t i c . c o m
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-01105 / rev. 1b / 08-23-10 / UD Series Utility Drawers
UD3
UD basic dimensions
All dimensions in inches unless otherwise noted [All dimensions in brackets are in millimeters]
UD1
BACK VIEW
SIDE VIEW
TOP VIEW
.75 [19] X 2.78 [71]
knockout
20.27 [515] maximum/
18.53 [471] minimum
rear support extension
(side mounting)
20.50 [521]
maximum/
15.50 [394]
minimum rear
rail support
extension
16.00
[406]
13.43
[341]
useable
surface
14.0 [356]
drawer
extension
15.93 [405]
useable width
19.00 [483]
1.25
[32]
FRONT VIEW
1.72 [44]
UD2, UD3, UD4
TOP VIEW
SIDE VIEW
FRONT VIEW
knockout for key lock
(part# Kylk)
or latch (part# Latch)
“B” mounting hole spacing
“A”
height
19.00 [483]
14.3 [365]
drawer
extension
14.56 [370]
useable
surface
.200 [51]
cable pass thru
15.9 [406]
useable width
Part #
“A”
Racking
Height
“B”
Mounting
Hole Spacing
“C”
Useable
Width
“D”
Usable
Surface
“E”
Drawer
Extension
Optional
Latch/
Keylock
Steel Gauge
Top & Sides
Steel Gauge Steel Gauge
Bottom
Front
UD1
1.75” (44) 1 space
1.25 (32)
15.93 (405)
13.43 (341)
14.00 (356)
No
20-gauge
20-gauge
20-gauge
UD2
3.50” (89) 2 space
3.00 (76)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
UD3
5.25” (133) 3 space
2.25 (57)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
UD4
7.00” (178) 4 space
4.00 (102)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
ITEM 22
I-00002
96-939/ rev 5 / 05-15-08
Middle Atlantic Products, Inc.
115 Volt Rackmount Power Strips
middleatlantic.com
EIA/TIA Compliant
Rackmount units provide economical
15 and 20 amp power distribution PD-915R / PD-915RC-20 / PD-920R-NS / PD-920R / PD-920RC-20
front view
Features
PD-815R-PL
front view
• UL Listed (file #E204950)
PD-915R-PL
• Available in 15 and 20 amp models
front view
• 8 circuit breaker protected rear outlets
PD-815RA-PL
• Enhanced surge protection with no surge diversion to ground
(PD-915, PD-920 and PD-815 Series only)
front view
• Two models available with front outlet and illuminated power
switch or pilot light for status indication
PD-815RC-PL
• Choice of finishes available: Black Brushed and Anodized,
Silver Brushed and Anodized, Black Powdercoat
front view
• Select models available with 20’ power cords
15 amp - rear view
Architects’ and Engineers’ Specifications
Rackmount power strip shall be Middle Atlantic Products model # __ (refer to
chart), with a __ amp power capacity (refer to chart), differential and common
mode surge and spike protection (surge and spike protection available on 15
amp power only) and EMI filtering. Enhanced surge protection with no surge
diversion to ground (PD-915, PD-920 and PD-815 series only). Rackmount
power strip shall operate on 115 volt AC/60Hz current. Rackmount power strip
shall include __' (refer to chart) 14/3 power cord with __ plug (refer to chart),
8 rear outlets (refer to chart), __ front outlet (s)(refer to chart), and __ amp
circuit breaker located on the power strip’s __ (refer to chart). Rackmount
power strip shall occupy one rackspace and be constructed of 18-gauge
phosphate pre-treated steel with a __finish (refer to chart). Rackmount power
strip shall be warranted to be free from defects in materials and workmanship
under normal use and conditions for a period of 3 years. Rackmount power
strip shall be UL listed in US and Canada.
c u sto mizab le sp e c ific atio n c lip s availab le at mid d le atlantic . c o m
Exceptional Support & Protection Products
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-939 / rev 5 / 05-15-08 / 115 Volt Rackmount Power Strips
20 amp - rear view
Rackmount Power Strips basic dimensions
All dimensions in inches [Bracketed dimensions are in millimeters]
TOP VIEW
8.75
[222]
FRONT VIEW
(PD-815RA-PL / PD815RC-PL)
REAR VIEW
1.75
[44]
19.00 [483]
(PD-920R-NS, PD-920R, PD-920RC-20)
(PD-920R-NS, PD-915R, PD-915RC-20, PD-920R, PD-920RC-20)
(PD-815R-PL)
(PD-815R-PL / PD-815RA-PL / PD815RC-PL)
PD-915R-PL
115 VOLT
(PD-915R)
(PD-915R-PL)
Part #
PD-815R-PL
PD-815RA-PL
PD-815RC-PL
PD-915R
PD-920R-NS
PD-915R-PL
PD-920R
PD-920RC-20
PD-915RC-20
15 AMP
60 HZ
Amps
15
15
15
15
20
15
20
20
15
Power Cord Type
NEMA 5-15P
NEMA 5-15P
NEMA 5-15P
NEMA 5-15P
NEMA 5-20P
NEMA 5-15P
NEMA 5-20P
NEMA 5-20P
NEMA 5-15P
# Front
Outlets
0
0
0
1
1
1
1
1
1
# Rear
Outlets
8
8
8
8
8
8
8
8
8
Circuit
Breaker
Location
Rear
Rear
Rear
Front
Rear
Rear
Front
Front
Front
Rear Outlet
Type
NEMA 5-15R
NEMA 5-15R
NEMA 5-15R
NEMA 5-15R
NEMA 5-20R
NEMA 5-15R
NEMA 5-20P
NEMA 5-20P
NEMA 5-15R
Cord
Length
9'
9'
9'
9'
9'
9'
9'
20'
20'
Finish
Black Powdercoat
Black Brushed and Anodized
Silver Brushed and Anodized
Black Powdercoat
Black Powdercoat
Silver Brushed and Anodized
Black Powdercoat
Black Powdercoat
Black Powdercoat
Surge Suppression & EMI Filter Specifications (PD-815R-PL / PD-815RA-PL / PD-815RC-PL / PD-915R)
• Nominal line voltage: 120 VAC
• Maximum line current: 15 Amps
• Maximum allowable voltage: 125 VAC (RMS)
- Maximum continuous voltage differential applied between
line and neutral
- Maximum clamping voltage: 395 volts@100 amps
• Peak impulse current (8/20 micro seconds):
- 30,000 amps, one time
- 21,000 amps, two times within 5 minutes
- 9,000 amps, ten times within 2 minutes
- Maximum peak impulse current pulse as defined between
line and neutral
- Maximum multiple impulse current derated per spec
• Response time: Instantaneous (Less than 1 nanosecond)
• EMI/ RF Suppression: More than 20 db
- Calculated line to neutral, 100 KHz to 1 MHz suppression
based upon nominal impedance
Middle Atlantic Products, Inc.
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
Networked Signal Processors
ITEM 23
bssaudio.com
Soundweb London
BLU-100
™
OVERVIEW:
The Soundweb London BLU-100 offers a fixed configuration of 12 inputs and 8 outputs, configurable signal processing
and a high bandwidth, fault tolerant digital audio bus.
The BLU-100 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette
of processing and logic objects and a “drag and drop” method of configuration provide a simple and familiar design
environment.
This processor features a low latency, fault tolerant digital audio bus of 48 channels which uses standard Category 5e
cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the
distance between devices to over 40km.
The BLU-100 is compatible with the entire Soundweb London family and its 48 channel digital audio bus represents
channels 1-48 of the larger 256 channel digital audio bus when integrated with the BLU-800, BLU-320, BLU-160, BLU-120 and BLU-BOB devices.
Analog Inputs provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom
Power per channel.
Phantom Power, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC,
from clear front panel LED indication. A bi-directional locate function allows devices to be identified both from and
within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-100 to be integrated with GPIO compatible devices. The
Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be
integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-100 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored
system solution.
K e y F e a t ures :
9 12 Analog Inputs (with 48v Phantom Power per
Channel)
9 8 Analog Outputs
9 Configurable Signal Processing
9 Rich Palette of Processing and Logic Objects
9 48 Channel, Low Latency, Fault Tolerant Digital
Audio Bus
9 Clear Front Panel LED Indication
9 Bi-Directional Locate Functionality
9 12 Control Inputs and 6 Logic Outputs for GPIO
Integration
9 Soundweb London Interface Kit for Third Party
Control System Integration (Documentation)
9 HiQnet Device
9 Configuration, Control and Monitoring from
HiQnet London Architect
Page 1 of 2
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
bssaudio.com
Networked Signal Processors
Soundweb™ London BLU-100
Te c h ni c a l S pe c ifi c a t ions :
Front Panel Led Indicators:
Per Input:
Signal Present, CLIP, 48V (Input only)
Other:
COM, STAT, ERR, PWR
Analog Inputs:
12 electronically balanced on Phoenix Combicon removable screw connectors
Mic/Line Inputs:
Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps
Input Impedance:
3.5kΩ
Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain
CMRR:
>75dB at 1KHz
Input Noise (E.I.N.):
<-128dBu typical with 150Ω source
Phantom Power:
48V nominal, selectable per input
A/D Latency:
37/Fs [0.77ms@48k]
Analog Outputs:
8 electronically balanced on Phoenix/Combicon removable screw connectors
Maximum Output Level: +19dBu
Frequency Response:
20Hz-20KHz (+0.5dB/-1dB)
THD:
<0.01% 20Hz to 20KHz, +10dBu output
Dynamic Range:
108dB typical, 22Hz-22KHz unweighted
Crosstalk:
<-75dB
Output Impedance:
40Ω balanced and 20Ω unbalanced
D/A Latency:
29/Fs [0.60ms@48k]
Control Ports:
12 inputs and 6 outputs
Control Input Voltage: 0 to 4.5v
Control Input Impedance:4.7kΩ to +5V (2-wire mode), >1MΩ (3-wire mode)
Logic Output Voltage: 0 or +5V unloaded
Logic Output Impedance:440Ω
Logic Output Current: 10mA source, 60mA sink
Watchdog Output: Phoenix/Combicon connector for failsafe control
Opto Output Current:
14mA maximum
Withstanding Voltage: 80V maximum (Off)
Series Impedance:
220Ω (isolated)
Control Network:
Connectors:
RJ45 Ethernet connector
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
BLU link:
Connectors:
2 x RJ45 Ethernet connectors
Maximum Cable Length: 100m/300ft on Category 5e cable between devices
Max. Number of Nodes: 60
Latency:
11/Fs [0.23ms@48k]
Pass Through Latency: 4/Fs [0.08ms@48k]
Power and Dimensions:
Mains Voltage:
100-240V AC, 50/60Hz
Power Consumption:
<55VA
BTU Rating:
<188 BTU/hr
Operating Temp. Range: 5 (41) to 35 (95) degrees C (degrees F)
Dims: (H(U) x W x D): 1.75" (1U) x 19" x 9.0" (45mm x 483mm x 229mm)
Weight:
6.4 lbs / 2.9 kg
BSS Audio incorporates high quality mechanical fans in some products. All mechanical fans have a limited life
expectancy. We recommend annual inspection of fans for dust occlusion and excessive noise. Fan assemblies should
be replaced after six to ten years of use. Environmental factors such as elevated temperature, dust, and smoke can
adversely affect fan life. Systems exposed to these conditions should be inspected more frequently. Fan replacement
can be performed either at the factory or by an experienced technician in the field. Please contact BSS Technical
Support for more information on purchasing replacement parts or product service.
Page 2 of 2
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | - Ph. +1 801-566-8800 | Fax +1 - 801-566-7662
18-0717
BSS Audio has a policy of continued product improvement and accordingly reserves the right to change features and
specifications without prior notice.
ITEM 24
bssaudio.com
Wall Controllers
Soundweb London
™
BLU-3, BLU-6, SW9012US and SW9015US
Soundweb
Soundweb
TM
TM
BLU-3
BLU-3
BLU-6
BLU-6
SW9012US
SW9015US
OVERVIEW:
The Soundweb London BLU-3, BLU-6, SW9012US and SW9015US Wall Controllers are simple analog wall controllers
which provide a cost-effective and familiar interface to even the most involved audio / video system.
The BLU-3 and BLU-6 are designed to be installed in a single-gang UK back box, while the SW9012US and SW9015US
are designed to be installed in a single-gang US back box. Electronically, the BLU-3 and SW9012US are identical and the
BLU-6 and SW9015US are identical.
The BLU-3 and SW9012US feature a five position source / preset selector and a level control. The BLU-6 and SW9015US
feature an eight position source / preset selector and an up / down pair of momentary buttons.
The simple analog wall controllers are designed to connect to the Control Inputs of the Soundweb London BLU-800, BLU-320, BLU-160, BLU-120, BLU-80, BLU-32 and BLU-16 devices. The BLU-3 and SW9012US require two Control
Inputs and the BLU-6 and SW9015US require three Control Inputs.
These controllers are configured using HiQnet London Architect and almost any parameter can be mapped to the
controls. However, the most common uses for these simple analog wall controllers are to select between sources and
control level for a single zone or select between presets and control level for a single zone.
The BLU-3, BLU-6, SW9012US, SW9015US and the other members of the Soundweb London family provide the building
blocks of the perfectly tailored system solution.
K e y F e a t ures :
9 Cost-Effective Control Solution
9 Familiar Control Interface
Page 1 of 2
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
bssaudio.com
Wall Controllers
BLU-3, BLU-6, SW9012US and SW9015US Wall Controllers
Tec h n ic a l S p ecific a t io n s :
Connector (BLU-3 and SW9012US):
Screw Terminals x 3:
GND connection (to Control Ports COMMON pin)
SOURCE / PRESET SELECT connection
LEVEL connection
Connector (BLU-6 and SW9015US):
Screw Terminals x 4:
GND connection (to Control Ports COMMON pin)
SOURCE / PRESET SELECT connection
LEVEL UP connection
LEVEL DOWN connection
Colors:
BLU-3 and BLU-6:
Blue
sw9012US and sw9012US: Beige
Dimensions (BLU-3 and BLU-6):
Dimensions (H x W):
3.35" x 3.35" (85mm x 85mm)
Dimensions (SW9012US and SW9015US):
Dimensions (H x W):
4.5" x 2.75" (114.3mm x 69.85mm)
Typical Connection Diagram (Works in Two-Wire Mode Only):
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | - Ph. +1 801-566-8800 | Fax +1 - 801-566-7662
18-0578
Page 2 of 2