ITEM NAME: Modern Wrought Iron Potting
SKU: WD-1882-1 (Box 1) & WD-1882-2 (Box 2)
PHOTO IMAGE
For assistance with assembly,please contact customer service
1-888-880-4884
1/9
PRE-ASSEMBLY PREPARATION:
!
* THIS ITEM IS PACKED IN TWO BOXES. BE SURE TWO BOXES HAVE BEEN RECEIVED *
• Please read through this instruction sheet before beginning assembly.
• It is recommended that two adult persons assemble this unit. • Make enough floor space for more organized assembly. Lay out all parts based on parts list to make sure all the parts are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Please check for any loose screws and tighten them before you use.
PRODUCT USAGE, CARE, AND MAINTENANCE:
!! PRODUCT IS HEAVY.
NEVER TRY LIFTING OR MOVING IT WITHOUT ASSISTANCE "
• Always try to keep unit clean to avoid possible staining and scratching. Use warm soapy water to clean any residue if needed.
• Keep surface away from any chemicals or immediately clean off in case of accidental contact .
• As with any outdoor iron product that is used heavily, surface is subject to wear and tear over time from outdoor elements and from every day use if not well kept.
2/9
PANEL AND FITTINGS INDENTIFICATION:
(A) REAR PANEL
Qty - 1pc
(D) OUTER BOTTOM SHELF PANEL
(F) CABINET TOP PANEL
(H) BOTTOM RAISED SHELF PANEL
(J) LEFT CABINET DOOR
(L) SINK
(B) LEFT PANEL
Qty - 1pc
Qty - 1 pc
Qty - 1 pc
Qty - 1pc
Qty - 1pc
Qty-1pc
( C ) RIGHT PANEL
Qty - 1pc
( E ) INSIDE CABINET BOTTOM SHELF PANEL
(G) TOP RAISED SHELF PANEL
(I) HANGING BAR
(K) RIGHT CABINET DOOR
(M) HOOKS
Qty - 1pc
Qty - 1pc
Qty - 1 pc
Qty - 1pc
Qty - 6pcs
3/9
HARDWARE PARTS LIST:
1) ALLEN BOLTS
3) HEX BOLTS (Medium Length)
5) FLAT GASKET
7) ALLEN WRENCH
Qty - 8pcs
Qty - 12pcs
Qty - 20pcs
Qty - 1pc
2) HEX BOLTS (Short Length)
Qty - 4pcs
4) HEX BOLTS (Long Length)
Qty - 4pcs
6) PE Hex Bolthead Covers
Qty - 20pcs
8) HEX WRENCH
Qty - 1pc
TWO ATTACHMENT METHODS USED FOR ASSEMBLY (READ INSTRUCTIONS):
1) USING ALLEN WRENCH TO TURN ALLEN BOLT
2) USING HEX WRENCH TO TURN HEXHEAD BOLTS
WITH GASKET
IMPORTANT - WHEN ATTACHING PARTS TOGETHER, DO NOT FULLY TIGHTEN SCREWS UNTIL AFTER ALL PARTS HAVE
BEEN ASSEMBLED TOGETHER. THEN GO BACK AND SECURELY TIGHTEN EACH BOLT
4/9
STEP-BY-STEP ASSEMBLY:
1
STEP 1:
Attach both right panel (C) and left side panel (B) to back panel (A), using 4pcs flat head Allen bolts (1) on each side. Use enclosed Allen Wrench to turn
bolts. DO NOT fully tighten bolts until after entire item is fully assembled.
2
STEP 2:
Attach outer bottom shelf panel (D) to bottom sides of both
left and right panels (B,C), using 2 pcs medium length hex bolts (3), flat gasket (5), and PE bolt cover (6). Use enclosed hex wrench to turn bolts. DO NOT fully tighten bolts until entire item is fully assembled. After bolts are fully tightened, cap bolt head with PE bolt cover.
5/9
STEP-BY-STEP ASSEMBLY:
3
STEP 3:
Insert inside cabinet shelf panel (E) , letting it rest on the side ledges above bottom shelf. No bolts needed.
4
STEP 4:
Place top panel with square opening (F) on top. Attach each end to sides of both right and left panels (B,C), using 2 pcs medium length hex bolts, (3), flat gaskets (5), and PE bolt covers (6). Use enclosed hex wrench to turn bolts. DO NOT fully tighten bolts until entire item is fully assembled. After bolts are fully tightened, cap bolt head with PE bolt cover.
6/9
STEP-BY-STEP ASSEMBLY:
5
STEP 5:
Place the smaller raised shelf panel into bottom position of sides of both left and right panels (B,C), using 2 pcs long
length hex bolts (4), flat gaskets (5), and PE bolt covers (6). Use enclosed hex wrench to turn bolts. DO NOT fully tighten bolts until entire item is fully assembled. After bolts are fully tightened, cap bolt head with PE bolt cover.
6
STEP 6:
Place the larger raised shelf panel into top position of the sides of both left and right panels (B,C) , using 2 pcs medium length hex bolts(3), flat gaskets (5), and PE bolt covers (6) on both sides of panel.
Use hex wrench to turn bolts. DO NOT fully tighten bolts until entire item is fully assembled. After bolts are fully tightened, cap bolt head with PE bolt cover.
7/9
STEP-BY-STEP ASSEMBLY:
7
STEP 7:
Attach hang bar (I) to sides of right and left panels (B,C) using 2 pcs medium length hex bolts(2), flat gaskets(5), and PE bolt covers(6). Use enclosed hex wrench to turn bolts. DO NOT fully tighten bolts until entire item is fully assembled. After bolts are fully tightened, cap bolt head with PE bolt cover.
8
STEP 8:
To mount door panels to workbench, slide hinge part on the door over counter part hinge mounted on the side panel, so it fits .
8/9
STEP-BY-STEP ASSEMBLY:
9
STEP 9:
Make sure all parts are positioned properly and snug. The go back and and tightened securely all bolt connections. Afterwards, cap each bolthead with PE bolt covers (6). Then drop sink into opening.
10
STEP 10:
Hang hooks (M) onto hang bar (I).
9/9