INSTALLATION INSTRUCTION
ACCIAIO
®
BX/HZ920
F L U O R E S C E N T
120V/277V, 347V or 480V Input
T5, T5HO, T8
WET LOCATION / IP66
HZ models: Class I, Division 2, Class I, Zone 2
Groups A, B, C & D, Hazardous locations
R
C
US
Chain mount (chain optional)
Surface mounting bracket
Safety cable
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Steel Housing
Die-cast aluminum
end cap
Model:
Operation
BX920, BX902S, HZ920, HZ920S
SA (AC & Emergency)
*not available on HZ models
Lamps
Input
217W
T8
214W
T5
224W
T5HO
228W
T5
232W
T8
254W
T5HO
120V / 277V
347V or 480V
Tempered glass lens
Stainless steel lock screw
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
040113
INSTALLATIONGUARDS
1. Make sure the main power is off.
®
2. Attach and secure ACCIAIO mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cables to safety brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
RELAMPING
1. Detach mounting brackets from housing having the fixture hang
from safety cables (If there is 48” clearance on site this
process is not necessary see) (figures 2, 3 & 4)
2. Loosen stainless steel screw from NON-FEED end cap and remove
end cap off.
3. Remove security crossbar (up – out motion)
4. Partially or completely slide out rail system until lamps are accessible.
5. Repeat the same process in reverse to close and seal the unit.
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
Safety cable
G
N L
2
Connect wires to main power.
(72” standard line cord provided)
power is off
4
Attach mounting
brackets to surface.
G
N
L
Snap fixture
to brackets.
3
5
Safety bracket
G
N
BLACK / HOT
WHITE / NEUTRAL
6
GREEN /GROUND
42.00
Canopy kit
(provided by others)
42.00
21.00
L
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cables to safety brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
Fixture completely installed.
RELAMPING
1
NOTE: step1 can be skipped IF YOU HAVE 48“ BETWEEN UNITS
2
Detach luminaire from surface mount
brackets using a flathead screwdriver. Unit is held by two safety
cables that allow the ACCIAIO® to drop down evenly
approximately 12” for easy accesibility.
3
Loosen stainless steel lock screw to release
non-feed, die-cast end cap.
4
Remove crossbar bracket in an up and out motion
for access to the ballast and lamp rail system.
Grasp
here and
pull
Ratcheted lamp sockets must be
turned to disengage and remove lamps
Reverse all steps to close and secure ACCIAIO®.
INSTALLATION INSTRUCTION
ACCIAIO
®
BX/HZ940
F L U O R E S C E N T
120V/277V, 347V or 480V Input
T5, T5HO, T8
WET LOCATION / IP66
HZ models: Class I, Division 2, Class I, Zone 2
Groups A, B, C & D, Hazardous locations
R
C
US
Chain mount (Chain optional)
Surface mounting bracket
Safety cable
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Model:
Operation
Die-cast aluminum
end cap
BX940, BX940S, HZ940, HZ940S
HT (AC Only)
SA1 (AC & Emergency - one lamp)
SA2 (AC & Emergency - two lamp)
*not available on HZ models
Steel Housing
Lamps
Input
432W
T8
428W
T5
454W
T5HO
120V / 277V
347V or 480V
Tempered glass lens
Stainless steel lock screw
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
040113
INSTALLATIONGUARDS
1. Make sure the main power is off.
®
2. Attach and secure ACCIAIO mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cables to safety brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
RELAMPING
1. Detach mounting brackets from housing having the fixture hang
from safety cables (If there is 48” clearance on site this
process is not necessary see) (figures 2, 3 & 4)
2. Loosen stainless steel screw from NON-FEED end cap and remove
end cap off.
3. Remove security crossbar (up – out motion)
4. Partially or completely slide out rail system until lamps are accessible.
5. Repeat the same process in reverse to close and seal the unit.
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
2
Connect wires to main power.
(72” standard line cord provided)
power is off
Safety cable
4
Attach mounting
brackets to surface.
G
N
L
Snap fixture
to brackets.
5
3
Safety Bracket
42.00
G
N
BLACK / HOT
WHITE / NEUTRAL
6
GREEN /GROUND
Canopy kit
(provided by others)
42.00
L
21.00
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cables to safety brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
Fixture completely installed.
RELAMPING
1
NOTE: step1 can be skipped IF YOU HAVE 48“ BETWEEN UNITS
2
Detach luminaire from surface mount
brackets using a flathead screwdriver. Unit is held by
two safety cables that allow the ACCIAIO® to drop down
evenly approximately 12” for easy accesibility.
3
Loosen stainless steel lock screw to release
non-feed, die-cast end cap.
4
Grasp
here and
pull
Remove crossbar bracket in an up and out motion
for access to the ballast and lamp rail system.
Ratcheted lamp sockets must be
turned to disengage and remove lamps
Reverse all steps to close and secure ACCIAIO®
INSTALLATION INSTRUCTION
ACCIAIO
®
BX/HZ950
single
COMPACT FLUORESCENT
120V/277V, 347V or 480V Input
WET LOCATION / IP66
DHZ models: Class I, DIvision 2, Class I, Zone 2
Groups A, B, C & D, Hazardous locations
R
C
2
Chain
mount (Chain optional)
1
Surface mounting bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Model:
Die-cast
aluminum
B
end cap
B
Steel Housing
Operation
Lamps
Input
BX950, BX950S, HZ950, HZ950S
HT (AC Only)
236W
CF
255W
CF
120V/277V
347V or 480V
Tempered glass lens
Stainless steel lock screw
IMPORTANT SAFEGUARDS
INSTALLATIONGUARDS
WARNING
A
1. Make sure the main power is off.
2. AAttach and secure ACCIAIO® mounting brackets to
surface. Use appropriate fasteners.
3. Bring the fixture up and snap mounting bracket onto
housing side channels.
4. Connect labeled wires to main power.
No User serviceable parts. Refer service to a qualified service technician.
This document
property of and contains
proprietary
to Beghelli,
Inc. It is submitted
in confidence
Readis the
instructions
prior information
to installing
and
/or operating
this
device.and is to be used solely for the
purpose for which it was furnished and returned upon request. This document and such information is not to be reproduced, transmitted, disclosed, or used
otherwise
in whole or in part
without prior
authorization
of Beghelli,
Inc. The recipient's
acceptance
of this document shall be considered an
Installation
should
be written
performed
by
a licensed
electrician
/ installer
agreement to the foregoing.
in accordance with local codes.
PART NAME
Beghelli
3250 Corporate Way
IMPORTANT
SAFETYGUARDS
Miramar, Florida 33025
UNLESS
OTHERWISE SPECIFIED
ALL DIMENSIONS = INCHES
MATERIAL
Ph: 954 442 6600
Fx:954 442 6677
www.beghelli.com
FINISH
ANGLES + 1
When using
electrical equipment, basic safety precautions should
DATE
DRAWN BY
DWG NO
always beTOLERANCES:
followed
including
the following:
.X = + 0.030"
Miguel Angel Pino
11/14/2011
.XX = + 0.015"
SIZE
SCALE
REF NO
SHEET
= + 0.005"
READ AND .XXX
FOLLOW
ALL SAFETY INSTRUCTIONS
DO NOT SCALE
2
1
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
040113
REV
RELAMPING
1. Loosen stainless steel lock screw from feed end cap
2. Release feed, die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
US
INSTALLATION
1
power is off
Attach mounting
brackets to surface.
G
WHITE / NEUTRAL
G
N
N
L
3
Snap fixture
to brackets.
BLACK / HOT
GREEN /GROUND
Canopy kit
(provided by others)
4
2
Connect wires to main power.
(72” standard line cord provided)
L
Fixture completely installed.
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to
surface. Use appropriate fasteners.
3. Bring the fixture up and snap mounting bracket onto
housing side channels.
4. Connect labeled wires to main power.
RELAMPING
1
2
Loosen stainless steel lock screw
from feed end cap
3
Grasp
here and
pull
Release feed, die-cast end cap.
4
Slide out rail system to access
the ballast and lamps.
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
INSTALLATION INSTRUCTION
ACCIAIO
®
BX/HZ950
duo
COMPACT FLUORESCENT
120V/277V, 347V or 480V Input
WET LOCATION / IP66
HZ models: Class I, Division 2, Class I, Zone 2
Groups A, B, C & D, Hazardous locations
R
C
US
Surface mounting
bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Die-cast aluminum
end cap
MA
NIT
RU
STE
Model:
SL
E
AV
T
NI
Operation
U
Lamps
Input
BX950, BX950S, HZ950, HZ950S
HT (AC Only)
436W
CF
455W
CF
120V/277V
347V or 480V
Steel Housing
Tempered glass lens
Jumper
cable
(with watertight
connectors)
Stainless steel lock screw
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
INSTALLATIONGUARDS
1. Make sure the main power is off.
2. Attach and secure ACCIAIO mounting brackets to surface.
(Use appropriated fasteners)
3. Bring MASTER fixture up and snap mounting brackets onto housing side
channels.
4. Bring SLAVE fixture up and snap mounting brackets onto housing side channels.
5. Connect MASTER and SLAVE using jumper cable with watertight connectors.
6. Connect MASTER fixture to main (AC) power following labels information.
7. Turn ON power.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
RELAMPING
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
1. Disconnet MASTER and SLAVE from jumper cable
loosen stainless steel lock screw from feed end cap.
2. Release feed, die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
SAVE THESE INSTRUCTIONS!
040113
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
G
power is off
N
L
WHITE / NEUTRAL
BLACK / HOT
Attach mounting
brackets to surface.
GREEN /GROUND
6
2
Connect wires to main power.
(72” standard line cord provided)
G
N
L
Snap fixture
to brackets.
14.370
3-4-5
Canopy kit
(provided by others)
3.150
Fixture completely installed.
1. Make sure the main power is off.
2. Attach and secure ACCIAIO mounting brackets to surface.
(Use appropriated fasteners)
3. Bring MASTER fixture up and snap mounting brackets onto housing side channels.
4. Bring SLAVE fixture up and snap mounting brackets onto housing side channels.
5. Connect MASTER and SLAVE using jumper cable with watertight connectors.
6. Connect MASTER fixture to main (AC) power following labels information.
7. Turn ON power.
RELAMPING
1
2
Disconnet master and slave from jumper
cable, loosen stainless steel lock screw
from feed end cap.
3
Release feed, die-cast end cap.
4
Grasp
here and
pull
Slide out rail system to access
the ballast and lamps.
12.539
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®.
INSTALLATION INSTRUCTION
ACCIAIO
®
BX/HZ960
Flood
COMPACT FLUORESCENT
120V/277V, 347V or 480V Input
WET LOCATION / IP66
HZ models: Class I, Division 2, Class I, Zone 2
Groups A, B, C & D, Hazardous locations
Mounting Bracket
R
C
Aluminum non-feed die-cast end cap
U Bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMPS / INPUT
Aluminum feed die-cast
end cap
Model:
Steel Housing
Operation
Lamps
Input
BX960, BX960S, HZ960, HZ960S
HT (AC Only)
236W
CF
255W
CF
120V/277V
347V or 480V
Stainless steel lock screw
Tempered glass lens
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
040113
US
INSTALLATIONGUARDS
Make sure the main power is off:
Loosen lock screw and detach feed die-cast end cap.
Loosen set screws / Slide mounting brackets
onto housing through channels.
Position mounting brackets 12” apart (keep set screws loose
until final adjustment).
Mount U bracket on desired surface against the containment
and use proper fasteners (provided by others).
Mount the fixture on installed U bracket using provided
screws.
Tighten set screws.
Adjust desired angle.
Connect labeled wires to main power.
Turn ON power.
RELAMPING
1. Loosen stainless steel lock screw from feed end cap
and release.
2. Release feed die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets.
Reverse all steps to close and secure ACCIAIO®.
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
Containment tab
1
2
Loosen only
(Do not remove)
Set screw (2)
Slide mounting brackets onto housing
up to containment tab.
Detach feed die-cast end cap.
3
4
12.0”
Angle
adjustment
Tighten set screw
N
L
Position brackets at (12”) apart
attach feed die-cast end cap.
Use proper fasteners
(provided by others)
G
Final mounting and adjustment.
RELAMPING
1
2
Loosen stainless steel lock screw
from feed die-cast end cap.
3
Release feed die-cast end cap.
4
Grasp
here and
pull
Slide out rail system to access
the ballast and lamps.
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®.