IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition. INSTALLATION INSTRUCTIONS CFT/CFTD970HEB, 1 & 2 LAMP HOUSINGS & REFLECTORS Reflector Bridge, Rotate 90° to upright position Wing Nut (2) Bridge Fasteners (2) DETAIL “A” J-Box/Ballast Cover This end towards wall for wall wash application J-Box Socket Mounting Bracket 6. Reflector Installation: Insert the two outer studs on the socket mounting bracket through the matching holes in the top of the reflector. Secure the reflector with two wing nuts. Adjustable Mounting Bracket (2) Plaster Flange Wing Nut (3)(Supplied w/HSG) 1-Lamp Reflector Shown Wall Wash Reflector Kicker Goes Away From Wall When Using Wall Wash Reflector. CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING. 101 Corporate Drive • Spartanburg, SC 29303 With representatives offices in principal cities throughout North America. Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A. Hours: 8am - 5pm ET 7. Push reflector with the socket mounting bracket attched into plaster flange aperture until flange on the reflector is flush against finished ceiling, align the center hole in the reflector bridge and secure with a wing nut. Note: Orientation of reflector for wall wash applications. 8. Install the proper lamps (by others). • Prescolite TollFree Technical Support 1.888.PRS.4TEC • 1. If reflector-holding-bridge is folded, rotate bridge to the upright position. Secure by tightening bridge fasteners, one on each side. 2. Bend mounting brackets as shown in Detail”A”. Install the fixture in the ceiling using mounting channels, bar stock, 1/2" inch EMT, or C-Channels, (by others), placed through the adjustable mounting brackets. Install the fixture in the ceiling so that the weight of the fixture is supported by the mounting channel or bar and/or hanger wires secured to the building structure. Note: Housing orientation for wall wash applications. 3. Adjust the fixture so the bottomof the plaster flange aperture is flush with the finished ceiling line and in aligned with adjacent fixtures. Secure mounting brackets by tightening wing nut on both sides of the fixture. 4. Remove J-Box cover plate. Remove appropriate knockout and assemble appropriate connector for the supply wire used. Connect ground wires to green ground leads. Connect white (common) to white (leads). Connect power supply (line) to black lead(s). Reinstall J-Box cover. WARNING: DO NOT pinch wires between J-Box/ballast cover and JBox. Consult a Qualified Electrician for all other options that require other wiring configurations. Mounting Brackets are Supplied Flat, Bend Brackets to align with marks on Flange www.prescolite.com InstructionSheet Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158510100 www.prescolite.com Reflector Bridge Install the Housing Per Instructions on Page 1 1. Reflector Istallation, 2-Piece Reflector: Insert the two outer studs on the socket mounting bracket through the matching holes in the top of the upper reflector. Secure the reflector with the wing nuts supplied with the housing. 2. Install the lamp(s). 3. Install the lower reflector by placing the reflector in the plaster flange aperture. Push the reflector upwards until the flange on the reflector is flush against the finished ceiling. Allow the three reflector springs to retain the lower reflector against the ceiling. Upper Reflector (1-Lamp Reflector Shown) Wing Nut (3) (Supplied W/ Housings) Lens Lower Reflector • Prescolite TollFree Technical Support 1.888.PRS.4TEC • InstructionSheet Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158510100 Hours: 8am - 5pm ET 101 Corporate Drive • Spartanburg, SC 29303 With representatives offices in principal cities throughout North America. Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.