4 Drawer dresser (5522) - Assembly and Operation Manual
Congratulations on purchasing an MDB Family product. This product will provide many years of service
if you adhere to the following guidelines for assembly, maintenance and operation. This product is for
residential use only. Any institutional use is strictly prohibited.
Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for
assembling the product in addition to the Allen wrench included in the hardware box. Do not use power
screwdrivers. All of our products are made from natural woods. Please understand that natural woods
have color variations which are the result of nature and not defects in workmanship.
DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARDWARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLISTIC VARIATIONS.
revised 26NOV2014
page 1
PARTS
A. Right
End
Panel
J. Right Drawer Panel (4)
B. Left
End
Panel
E. Dresser Top
K. Left Drawer Panel (4)
F. Bottom Support Frame
C. Drawer
Bottom
Board (4)
M. Front Drawer Panel (4)
G. Top Support Frame
O. Back Drawer Panel (4)
H. Support Bar (3)
Support Bar
Q. (Q)Back
Back Support
Barx 1
P1. Left
leg (2)
D. Back Panel (2)
P2. Right
leg (2)
N. Base Panel
(D)Back Panel x 2
HARDWARE
H1. 1-1/8” Machine
Bolt (22)
H2. Cam Lock
Bolt (8)
H3. Cam Lock (8)
H7. Large
H12. Leg Wood H13. Support Bar
Fastener (8)
Wood Screw (16) Screw (8)
H4.Knob (8)
H5. Knob
Bolt (8)
H14. Wood H15. Plastic Plug (4)
Dowel (4) H15.Capuchon en
plastique (4)
H8. Right Panel Glide (4)
H10. Right Drawer Glide (4)
H9. Left Panel Glide (4)
H11. Left Drawer Glide (4)
H6. Small Wood
Screw (100)
Tools Needed
(not included)
Phillips
screwdriver
page 2
1
Step 1: Installing the Rail Glides
Installing the panel glides.
Install the panel glides (H8) and (H9) onto the end panels
(A) and (B). Use 3 wood screws (H6) for each glide.
A
B
Step 2: Assemble Dresser End Panels, Support
Frames and Support Bars
2
Assemble dresser end panels,
support frames and support bars.
DO NOT OVER TIGHTEN.
Make sure top support frame
(G) is placed with counter-sunk
holes facing down.
Use screws (H6)
and support bar
(H)(Q)to the Ieft and right
fastener (H13) to mount support
bars (H) and (Q) to the left and right
end panels (A) and (B).
(Q)
Place bottom frame support
frame (F) with counter-sunk holes
facing up.
DO NOT OVER TIGHTEN.
page 3
3
Step 3:
Assemble
dresser
Assemble
Dresser
Top top.
Use 8 bolts (H1) to install the dresser top (E).
4
Back Panel Assembly.
Use 12 screws (H6) for back panel.
(H6)
(H6) (H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
DO NOT OVER TIGHTEN.
5
6
Assemble Base and Legs.
Use 8 (H12) wood screws to install legs (P).
Drawer Assembly
Step 6A.
(H14)
(H14)
(H14)
(H14)
(H15)
(H15)
(H15)
(H15)
H14
(H15)
There are no pre-drilled holes on
base panel for H12. Align carefully
and secure legs. Then attach base
panel assembly to the dresser
assembly using 6 (H1) machine bolts
as shown in the picture.
page 4
Drawer Assembly
Drawer Assembly
Step 6B.
Step 6C.
Drawer Assembly
Step 6D.
Drawer Assembly
Step 6E.
Drawer Assembly
Step 6F.
7
Insert the assembled drawers.
This item has a manufacturer’s limited one year warranty.
Visit our web site at www.themdbfamily.com for more information.
page 5
8
FURNITURE ANTI-TIPPING KIT INSTALLATION
Serious or fatal crushing can occur when furniture tips over on children. To help prevent tip-over, follow the
steps below to install this anti-tipping strap.
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
X1
Place heaviest item in the lowest drawers.
Unless specifically designed to accommodate,
do not set TVs or other heavy objects on
top of this product.
Never allow children to climb or hang on
drawers, doors, or shelves.
Never open more than one drawer at a time.
(OR)
Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is permanent label. Do not attempt to remove!
X1
X2
X1
Tools Needed (not included)
Stubby
Screwdriver
Pencil
Phillips
screwdriver
8a
Locate a 2” x 4” stud behind the
wall, and make a mark.
2” x 4” wall stud
page 6
8b
Install the strap on the wall with
long screw and washer.
8c
Install the other end of strap on
the back of dresser with short
screw and washer into the wood
framing of the dresser.
KEEP THIS MANUAL IN A SAFE
PLACE FOR FUTURE REFERENCE.
READ ALL INSTRUCTIONS BEFORE
USING THE PRODUCT. KEEP THE
INSTRUCTIONS FOR FUTURE USE.
Safety Notes:
Finish
• Do not allow your children to climb or jump on the furniture or in the drawer. Climbing on the furniture could make
it top-heavy and cause the furniture to damage or tip over.
• Never move or push heavy furniture by yourself as it can cause the furniture to tip over.
• This furniture is not intended to support TV or other heavy items.
page 7
• Do not overload the drawers.