Only with correct
selection and
maintenance will
your head protection
be ready for the
unexpected.
HEAD PROTECTION
Helmets are
designed to
protect you from
falling objects.
Don’t gamble with safety.
93
HELMETS
HELMET SELECTION
Brand your
helmet
SEE PAGE 97
Helmets vs
bump caps
When choosing a helmet or
bump cap, it is important to assess
your hazards.
• Helmets are used where there is
a danger from a falling mass.
• B ump caps are designed for
where bumps or scrapes from a
fixed hazard could occur.
630 POLYCARBONATE HELMET
• Constructed from high performing
polycarbonate material for greater
resistance to temperature and colour fading.
Giving a longer operational life
• Certified to AS/NZS1801 – Type 2
• Colours: Fluoro Yellow, Fluoro Orange & White
CODE 4
10909 Vented
410910 Non Vented
HEAD PROTECTION
ACCESSORIES
IMPORTANT CONSIDERATIONS
Helmets conform to AS/NZS1801.
Bump caps do not have an industry
standard.
411306 Reflective decal set
• AS/NZS 1801 recommends that
head harnesses be replaced
every two years
• Does the helmet need to be
securely fitted with straps for
working at height?
• What accessories will be used if
any and how will this effect other
Personal protective equipment
(PPE)
HI-VIS HELMETS
210951L Elastic chin strap
410916 Linesman strap
630 ACCESSORIES
CODE 4
10913 Pin Lock suspension kit
410912 Ratchet suspension kit
410916 Linesman strap
408121 Replacement sweat band
210951L Elastic chin strap
411306 Reflective decal set
• ABS fluorescent
coloured helmets are
designed to be used in low light
areas such as forests, indoors or
underground work
Brand your
helmet
• In full sunlight, the life of a fluorescent
ABS helmet may be reduced
• POLYCARBONATE fluorescent
coloured helmets are less likely to
be effected by deterioration under
high UV light so are ideal for
outdoor workers
• Damage caused by UV can be
identified as the helmet will lose its
glossy finish and eventually take on a
chalky appearance
410913 P in Lock suspension kit
SEE PAGE 97
630 ABS HELMET
• Constructed from lightweight, durable
ABS material
• Vents on top, front and rear of the helmet
allow maximum cooling for wearer comfort
• A single six point suspension unit offers
unrivalled comfort and performance
• The slip lock system makes fitting of visors,
earmuffs and other accessories easy
• Certified to AS/NZS1801 - Type1
• Colours: White, Yellow, Red, Blue
CODE 4
10907 Vented
410908 Non Vented
94
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)
410912 R atchet suspension kit
HELMETS
Brand your
helmet
SEE PAGE 97
620 ABS HELMET
• Sleek vented helmet is constructed from
lightweight plastic
• Six point suspension unit
• Vents on top, front and rear of the helmet
allow maximum cooling for wearer comfort
• Slip lock system makes fitting of visors,
earmuffs and other accessories easy
• Certified to AS/NZS1801 - Type1
CODE 6
20 ABS White, Yellow, Red, Blue, Green
408042 Polycarbonate Fluoro Yellow, Fluoro Orange
620 LINEWORKERS HELMET
620 ACCESSORIES
Designed for working at height with the
added security of a four-point head harness
to keep it in place in the event of a fall.
• Ratchet suspension system for quick and
secure fit
• Peak-less option for added range of vision
• Certified to AS/NZS 1801:1997 Type 1
CODE 5
00152 Suspension kit
500153 Replacement sweatband
401395 Replacement ratchet suspension
210951L Elastic chin strap
Brand your
helmet
SEE PAGE 97
CODE 4
04360 Peaked ABS White, Yellow, Red
550464 Peakless ABS White, Yellow, Blue, Green, Red
408044 Peaked Polycarbonate Fluoro Orange, Fluoro Yellow
408045 Peakless Polycarbonate Fluoro Orange, Fluoro Yellow
CARE & MAINTENANCE
HEAD PROTECTION
ACCESSORIES
610 ABS VENTED HELMET
• Features a six point suspension unit and
vents on the top to allow a cooling airflow
for wearer comfort
• Slip lock system makes fitting of visors,
earmuffs and other accessories easy
• Economical vented helmet constructed
from lightweight plastic
• Certified to AS/NZS1801 - Type1
CODE 407189 White, Yellow, Red, Blue, Fluoro Yellow, Fluoro Orange
When not in use, helmets must be
stored in a cool, dry environment
away from direct sunlight, heavy or
sharp objects and chemicals.
• T he shell of the helmet can be
weakened by exposure to paints,
paint thinners, adhesives and
some cleaning agents. These may
also reduce electrical resistance
•E
nsure that any stickers or decals
use a non-solvent based adhesive
ACCESSORIES
•E
xtreme heat can reduce the
strength of the helmets. Do not
stored or transport helmets on the
front or rear-window shelves of
vehicles or in direct sunlight
610 ACCESSORIES
CODE 4
08120 Suspension kit
408121 Replacement sweat band
210951L Elastic chin strap
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)
95
HELMETS & BUMP CAPS
MONITOR HELMET
SERVICE LIFE
Remain protected
and compliant
When helmets are purchased the
issue date must be written into the
helmet on the manufactures label
inside the helmet.
SEETHRU VENTED HELMETS
• Transparent polycarbonate shell and peak
allows the wearer to look upwards without
the need to tilt the head back, causing
discomfort in the neck over time
• No need for the wearer to reverse the head
harness in the helmet in order to allow
clearer vision while looking upwards
• UV400 stabilized and is suitable for indoor or
outdoor use
• Adjustable 6 point webbed harness
• Available in Clear, Smoke, Red, Blue,
Green, Orange, Pink and Yellow
• Approved to
AS/NZS 1801:1997 Type 2
HEAD PROTECTION
CODE 410350
Standard compliance
VERTEX HELMETS
Helmet for work at height and rescue.
• Chinstrap designed to reduce the risk of the
helmet falling off as a result of an impact
during a fall
• Accessories can be easily added
• Vertex Best approved to CE ANSI Z89.1-2003
Type 1 Class E
• Vertex Vent approved to CE EN 12492,
ANSI Z89.1-2003 Type 1 Class C
CODE 4
06783 Vertex Best
406784 Vertex Vent
Measured from the date the helmet
is first worn;
Manufacturers recommend;
• Three years for the helmet shell
Brand your
bump cap
• Two years for the harness
• Helmets need to be inspected
at least weekly for signs of dents,
cracks, penetration and any
damage due to impact, rough
treatment, or wear. Any hard hat
that fails the visual inspection
should be removed from service
until the problem is corrected
BUMP CAP
SEE PAGE 97
SKULLERZ® 8950 BUMP CAP SHORT BRIM
SKULLERZ®
8950 BUMP CAP - LONG BRIM
• Unique flanged shell design for a
comfortable fit and air flow
• Nylon Taslan cap construction with
reflective accents
• Strategically placed side and rear mesh
venting panels
• Short brim (50mm)
• EN 812: 2012 certified
• Colours: Black, Fluoro Yellow
• Unique flanged shell design for a
comfortable fit and air flow
• Nylon Taslan cap construction with
reflective accents
• Strategically placed side and rear mesh
venting panels
• Baseball-style long brim (80mm)
• EN 812: 2012 certified
• Colours: Black, Fluoro Yellow
CODE 410959
CODE 410958
• Lightweight polyethylene cap provides
protection against bumps and scalp
lacerations in areas with low head
clearance
NOT TO BE USED TO PROTECT AGAINST IMPACT
CODE 8
6 Bump cap
S86 Suspension kit
B86 Sweatband
96
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)
VISOR COMBINATIONS
VISOR TYPES
Mesh
PELTOR FORESTRY COMBO
Excellent eye guard against wood
chips and branches and no problem
with fogging up. Wear protective
goggles when there is any risk of
injury to the eyes by particles that
may penetrate the visor.
• Low impact rated visor V4A,
AS/NZS 1337.2:2012
• Class 5 SLC80 28dB Earmuffs
CODE 4
11072 Forestry Combo Complete
V4A Forestry visor and browguard
H7P3M Class 5 earmuffs only
406539 Z3G Adaptor to connect visor to 610 or 630 helmet without earmuffs
Medium impact
High impact
These visors have the same
capability as the medium impact
visors but with higher protection
levels of impact, heat resistance and
chemical resistance.
HOWARD LEIGHT FORESTRY COMBO
• Class 5 SLC80 28dB Earmuffs
CODE 4
11073 Forestry combo complete
3810 Mesh visor only
401568 Class 5 Leightning® L1 earmuff only
3713 Adaptor to connect visor to 610 or 630 helmet without muffs
Secondary protection
It is recommended secondary eye
protection (safety glasses or goggles)
should be used under a face shield.
YOUR
LOGO HERE
HELMET BRANDING
CODE 2
10404L Art setup charge (one off charge)
210501L Set up charge (50 plus no charge)
550162 1 Colour
550163 2 Colour
550164 3 Colour
550181 4 Colour
RE
RECYCLING
YOUR
LOGO HERE
CLAB
CY
LE
Identify people on site and
enhance your corporate
image by personalising
your Safety Helmets.
FOR MORE INFORMATION ON
IMPACT RESISTANCE, SEE PAGE 102.
HEAD PROTECTION
Offers protection from chemical
splash and impact from high speed
flying particles. These visors can be
attached to either a safety helmet
where head protection is also required
or to a head mounted browguard.
ABS Helmets
are recyclable
Bring your old helmet in to a
NZ Safety branch and we’ll make
sure it gets recycled.
HEADGEAR COMBINATION
FORESTRY MESH
• A versatile and comfortable solution
for wearers who require face and
hearing protection
• Headband-adjustable
• Forestry model has a low impact rated
stainless steel mesh visor (411075),
AS/NZS 1337.2:2012
• Peltor™ Slimline Earmuffs Class 4
CODE 4
11074 G500 Forestry Combo
411075 5C Replacement Mesh Visor
406395 Hygiene kit for earmuffs
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)
97
VISORS & ACCESSORIES
ARMADILLO FACE SHIELD
• Medium to high velocity impact
• Provides protection from chemical splash
and high temperatures
• It can be used in conjunction with half
mask respirators and earmuffs
HEAD PROTECTION
CODE 1
12105 Browguard with clear visor
550396 Browguard with grey visor
112018 Replacement clear visor
550393 Replacement grey visor
411089 Replacement shade 5 visor
112021 Replacement sweatband
BIONIC® FACE SHIELD
• Browguard with high impact anti-fog
polycarbonate visor (sold separately)
• Simplest and most comfortable face shield
designed to handle any challenge
• Designed for rugged jobs, it’s tough where
it has to be, yet extremely lightweight and
balanced for all day comfort
CODE 4
03373 Browguard only
60022L Polycarbonate replacement high impact visor
CODE 4
04213 Bionic face shield and clear visor
404214 Replacement clear visor
404215 Replacement shade 5 visor
HELMET NECK FLAP
THERMAL MERINIE – HELMET LINER
• 100% Wickable Polyester to help keep
the wearer cool
• UPF 50+ for excellent UV protection
• Colour: Fluoro Orange
HELMET NOT INCLUDED.
• 95% Merino Wool, 5% Lycra
• Recognised by WorkSafe NZ as a
practical solution for use under helmets
• Colours: Black, Navy
• Made in New Zealand
CODE 406711
CODE 407032
PROSAFE FACE SHIELD
ACCESSORIES
HELMET SUN BRIM
WITH NECK FLAP
CODE 159247
YOU MAY ALSO BE
INTERESTED IN:
DOES NOT PROVIDE IMPACT PROTECTION
ATV HELMET
• Complies with NZS8600 Safety Standard All Terrain Vehicle Helmets
• Fully adjustable
• Unimpeded visibility and hearing
• Good ventilation - not too hot to wear
• More durable than regular motorcycle
helmets - UV resistant shell, lining not
susceptible to parasites
• Much lighter than a motorcycle helmet 590gm
CODE 402732
98
GO TO PAGE
83
IMPACT RESISTANT
POWERED AIR HEAD TOP
DISPOSABLE SPLASH VISOR
• Acetate lens with foam brow pad and
elastic headband
• Protection against splash such as blood
products (leptospirosis)
CODE 501228
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)