www.TaillightSolutions.com
Rear Fog Lamp conversion harness installation instructions
For 2007 – 2010 Jeep Grand Cherokee SRT-8 models
______________________________________________________________________________
WARNING
DO NOT BEND THE HARNESSES MORE THAN 90 DEGREES AT ANY POINT OR DAMAGE COULD RESULT.
_____________________________________________________________________________
NOTE: This harness kit will only work for the above listed vehicles that are equipped with dual bulb tail
light assemblies (one tail light bulb and one reverse bulb). The male and female tail light plugs are
designed to mate (connect) with the stock plugs that the vehicle should already be equipped with. If you
determine that the plugs are different and do not mate with the plugs on this kit DO NOT attempt to
force them together or alter them in any way. After successful installation of these harnesses please be
sure to verify that the rear fog lamps operate as advertised. If you have any problems or questions
please feel free to contact me at info@Taillightsolutions.com
NOTE: If you purchased an LED version harness kit you MUST install LED tower bulbs in the
rear fog lamp housings. Failure to do so WILL RESULT in serious damage.
Step 1
Starting with either side tail lamp remove the two plastic locking clips or bolts that hold the assembly to
the body of the vehicle.
Step 2
Pull the tail lamp assembly back until the two tabs are free from the body. BE CAREFUL not to pull the
assembly outwards from the vehicle or the tension tabs will break.
Step 3
Carefully unplug the stock 3 wire harness from the tail lamp bulb socket. NOTE: The small red
locking tap must be completely pulled back (unlocked) before the harness can be unplugged.
Step 4
Obtain the new harness and insert the matching (female) plug onto the bulb socket. Make sure
the plug is fully seated and locked (red tab forward).
Step 5
Now plug the 3 wire male plug from the new harness into the female plug that was removed
from the tail light bulb socket in step 3. Make sure the plugs are fully seated and locked (red tab
forward).
Step 6
Route the two wire plug at the end of the conversion harness down the body cavity until it can
be grasped from underneath the vehicle. After the plug has been properly routed re-install the
tail light assembly the same way it was removed in steps 1 and 2.
Step 7
(Skip this step if your SRT-8 does not have pre-wired rear fog lamps)
Locate the rear fog lamp assembly and unplug (if applicable) the existing 2 wire plug and secure
it with tape (or wire ties) so it will not be exposed and hanging free. This plug will not be used
again.
Step 8
Plug the two wire plug from the new conversion harness into the rear fog lamp bulb socket.
Make sure the plug is facing the proper direction and you hear a click to verify it is locked in
place. DO NOT force this plug into the socket if it will not lock.
Step 9
Repeat the same procedure for the opposite side and test the rear fogs for proper operation.
They should act just like the factory rear tail lights except for reverse. You should now have
parking lights, brake lights, turn signals, and hazard flashers from your rear fog lamps.
If one or both of the rear fog lamps do NOT illuminate after the installation but the associated
tail light does operate as designed, check to make sure the rear fog lamp bulbs are not
damaged or burned out. The halogen bulbs that fit in the rear fog housings are single element
type 1156/1157s that can be obtained at any auto parts store.
If you are using an LED harness you will need 1 pr of 1156 single intensity (RED) LED towers.
They can be obtained from Taillight Solutions or most other specialty automotive lighting
retailers.
_____________________________________________________________________________
WARNING
DO NOT BEND THE HARNESSES MORE THAN 90 DEGREES AT ANY POINT OR DAMAGE COULD RESULT.
_____________________________________________________________________________
Disclaimer
Our products and services carry a 1 year warranty. If you have any problems within the first
year of your purchase we will repair the defect at our expense.
All of our electrical related work is always tested for proper and complete operation before
being shipped. If you experience any problems please contact us for support before continuing
with the installation. If we determine that the problem is installation related we will attempt to
assist you or you will need to locate a qualified automotive electronics technician to complete
the installation.
If it is determined that our products are damaged or defective due to anything other than a
manufacturers related issue we will not be able to warranty the product and it will be the
responsibility of the buyer to pay for the repair or replacement product.
In addition, Taillight Solutions will not be held responsible / liable for any damage that may
result due to negligent / improper installation, lack of knowledge, carelessness, or modification
of this product. This seller will also not be held responsible or liable if this electronics accessory
violates any terms of the buyers vehicle warranty.
Due to the sensitive nature associated with vehicle electronics it is highly recommended that
this product be installed by qualified personnel.
www.TaillightSolutions.com