NZQA Expiring unit standard
1318 version 8
Page 1 of 4
Title
Measure, mark out and cut material for production by canvas
fabrication
Level
3
Credits
6
Purpose
This unit standard is for people who work in the canvas
fabrication and allied industries. People credited with this unit
standard are able to: obtain dimensions for marking out; select
material; mark out job pieces; and cut out pieces.
Classification
Outdoor Fabric Products > Canvas Fabrication
Available grade
Achieved
Explanatory notes
The following legislation (and subsequent amendments) is applicable to this unit standard
and must be followed where applicable:
–
Health and Safety in Employment Act 1992.
Outcomes and evidence requirements
Outcome 1
Obtain dimensions for marking out for canvas fabrication.
Evidence requirements
1.1
Overall sizes are established according to client specification.
Range
from sketch, drawing, plan, sample, specification.
1.2
Individual piece sizes are determined according to company policy.
1.3
Allowances are applied to each piece according to company policy.
Range
1.4
seams, hems stretch, shrinkage.
Piece marking out dimensions are recorded according to company policy.
Range
workbook job card.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
1318 version 8
Page 2 of 4
Outcome 2
Select material for canvas fabrication.
Evidence requirements
2.1
Material type is determined for each piece according to client specification and
company policy.
Range
specification, sample, workplace directive.
2.2
Material is selected from storage according to company policy.
2.3
Material is checked for faults and size to ensure it can accommodate the job
according to company policy.
2.4
Safe working practices are carried out throughout the task.
Range
personal safety; safety of other people; workshop safety; tool,
equipment, and machine safety.
Outcome 3
Mark out job pieces for canvas fabrication.
Evidence requirements
3.1
Layout of the pieces is determined for the most economic use of material
according to company policy.
Range
3.2
Pieces are marked out on the selected material using appropriate marker
according to company policy.
Range
3.3
job specification, fabric characteristics.
markers – french chalk, felt pen, biro, pencil, chalkline.
Piece alignment marks are applied according to company policy.
Range
pen, chalk, holes, cuts, nicks.
3.4
Pieces are marked for product and assembly identification according to
company policy.
3.5
Safe working practices are carried out throughout the task.
Range
personal safety; safety of other people; workshop safety; tool,
equipment, and machine safety.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
1318 version 8
Page 3 of 4
Outcome 4
Cut out pieces for canvas fabrication.
Evidence requirements
4.1
Tool for cutting out is selected and checked for sharpness according to
company policy.
4.2
Pieces are cut out to the marked lines at the workplace required speed
according to company policy.
4.3
Pieces are assembled ready for fabrication according to company policy.
4.4
Safe working practices are carried out throughout the task.
Range
personal safety; safety of other people; workshop safety; tool,
equipment, and machine safety.
Replacement information
This unit standard has been replaced by unit standard
23487, unit standard 23488, unit standard 23493, and
unit standard 23494.
This unit standard is expiring. Assessment against the standard must take place by
the last date for assessment set out below.
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
3 August 1995
31 December 2016
Revision
2
16 September 1997
31 December 2016
Revision
3
4 November 1997
31 December 2016
Revision
4
28 May 1998
31 December 2016
Review
5
17 August 1999
31 December 2016
Review
6
26 March 2007
31 December 2016
Rollover
7
19 November 2010
31 December 2016
Rollover
8
20 November 2015
31 December 2020
Consent and Moderation Requirements (CMR) reference
0014
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
1318 version 8
Page 4 of 4
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA, or
an inter-institutional body with delegated authority for quality assurance, before they can
report credits from assessment against unit standards or deliver courses of study leading
to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Consent requirements and an outline of the moderation system that applies to this
standard are outlined in the Conesnt and Moderation Requirements (CMR). The CMR
also includes useful information about special requirements for organisations wishing to
develop education and training programmes, such as minimum qualifications for tutors and
assessors, and special resource requirements.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016