. INSTALLATION INSTRUCTIONS V90271 REV A QUIET CEILING SPECIAL CEILING METAL HALLIDE QCT910,QCT911 BASED SERIES Page 1 of 3 Avoid Fire or Electric Shock THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. *Installation Instructions for qualified electricians only. *Install per National Electrical Code and local regulations. *Read Installation Instructions completely before installation. *Failure to follow Installation Instructions may void warranties. Fixture Mounting: 8. Butterfly Mounting (Commercial): 1. Fixture comes equipped with Universal Butterfly Mounting brackets and can take common 1 inch or 1-1/2 inch Black Iron or Galvanized Mounting Channels (Supplied By Others). Hanger bars can be used with grid ceilings having T bars and joist installations of wood.Adjustable hanger bars are for use in installations with spacing from 12" to 24", while maintaining minimum 1/2" spacing around fixture Grid Ceiling Installation (Figure 2): 2. Position Fixture so the Mounting Channels lie on top of ceiling runners. Step 1 Extend bar hangers between the T bars and slide the slots in the mounting tabs over the T-bars. 3. Fasten Mounting Channels securely to ceiling runners. 4. Secure Mounting channels to Universal Butterfly Mounting Brackets with wire tire downs. Step 2 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked in the position by tightening bar hanger locking screws on housing platform.See Detail 3A. 5. Adjust elevation of Fixture so Mudding Ring Edge will be flush with surface of finished Ceiling by loosening two (2) 1/4 inch Hex Screws on both Universal Mounting Brackets. See Fig. 1. 6. Tighten two (2) 1/4 inch Hex Screws on both Universal Butterfly Mounting Brackets to secure Fixture. See Fig. 1. Step 1 Extend bar hangers to fit between joist and position mounting tab locater lip tight to bottom of joist or framing member. Bar hangers should be level with bottom of joist or framing member. Step 2 Attach bar hangers to joist or framing member using appropriate hardware for material. Hanger Bar Mounting (Residential): 7. Joist Installation (Figure 3): Adjustable hanger bars are preassembled with mounting bracket and provided with fixture.The preassembled hanger bars must attached to the fixture prior to installation.Align with two screws on end of fixture and tighten .Hanger bars are installed in Fig.1. Step 3 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked into position.See Detail 3B.Nail Supplied in hanger bars will be suitable. Mounting Channel (Supply by Others) Fixture Housing Cover Bracket Optional "T" 1/4" Hex Screw Hanger Bars Universal Butterfly Mounting Bracket Aperture Ring Trim Mechanism Screw Mudding Ring Safety Cable Figure 1 Figure 2 INSTALLATION INSTRUCTIONS V90271 REV A QUIET CEILING SPECIAL CEILING METAL HALLIDE QCT910,QCT911 BASED SERIES Page 2 of 3 Avoid Fire or Electric Shock THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. *Installation Instructions for qualified electricians only. *Install per National Electrical Code and local regulations. *Read Installation Instructions completely before installation. *Failure to follow Installation Instructions may void warranties. 9. Install Ceiling drywall up to Aperture Ring on Fixture See Fig. 4. 10. Position Aperture Ring to be in plane with Ceiling.See Fig.4 360 Rotational Lamp Adjustment (Round Trim Only) IF LOCKING KNOB IS UNLOCKED: Detail 3A Detail 3B 11. Rotate Trim Mechanism to desired lamp bean position by turning Trim Mechanism up to 360 Degrees. 12. To lock positioning, remove Trim Mechanism being careful not to change position. 13. Tighten Lock Knob inside Fixture to lock Rotational adjustment Ring. See Fig.5. 14. Be careful to align Tab Alignment Feature on Trim Mechanism with Tab Alignment feature Notch in Rotational Adjustment Ring while installing trim after rotational adjustment. 15. Connect Safety Cable attached to Trim to Fixture by inserting Safety Cable through opening in Fixture and inserting Snap Hook (See Fig. 1) on end of Safety Cable into hole in Bracket attached to inside of fixture.Install trim mechanism into fixture by pressing firmly to engage Retainer Spring Clips . See Fig.4. Figure 3 Rotational Adjustment Ring Lock Knob IF LOCKING KNOB IS LOCKED: Fixture Mudding Frame Bracket 16. Remove Trim Mechanism from Fixture. 17. Loosen Lock Knob inside Fixture. Ceiling 18. Ball Detent Catch Trim Mechanism Figure 4 To lock positioning, remove Trim Mechanism being careful not to change position. 19. Tighten Lock Knob inside Fixture to lock Rotational adjustment Ring. See Fig.5. 20. Be careful to align Tab Alignment Feature on Trim Mechanism with Tab Alignment feature Notch in Rotational Adjustment Ring. INSTALLATION INSTRUCTIONS V90271 REV A QUIET CEILING SPECIAL CEILING METAL HALLIDE QCT910,QCT911 BASED SERIES Avoid Fire or Electric Shock Page 3 of 3 *Installation Instructions for qualified electricians only. *Install per National Electrical Code and local regulations. *Read Installation Instructions completely before installation. *Failure to follow Installation Instructions may void warranties. 21. Connect Safety Cable attached to Trim to Fixture by inserting Safety Cable through opening in Fixture and inserting Snap Hook (See Fig. 1) on end of Safety Cable into hole in Bracket attached to inside of fixture.Install trim mechanism into fixture by pressing firmly to engage Spring Clips.See Fig.4. Rotational Alignment Ring Ceiling Joist Locking Knob Tab Alignment Feature Notch Fixture Figure 5 (Fixture Cover Removed For Clarity) THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.