w
w
ap
eP
m
e
tr
.X
w
7040/01
Paper 1
October/November 2005
2 hours 40 minutes
Additional Materials:
A2 Drawing Paper (1 sheet)
Standard Drawing Equipment
READ THESE INSTRUCTIONS FIRST
Print your Centre number, candidate number and name at the bottom right-hand corner of your Drawing
Paper.
Use both sides of the paper for your answers.
Do not use staples, paper clips, highlighters, glue or correction fluid.
Answer five questions.
Answer not more than three questions from any one section.
Unless otherwise stated, strictly geometrical methods must be used, solutions are to be drawn full size and
no dimensions are required. All construction lines must be shown clearly, but lines which are parallel to,
perpendicular to or inclined at angles of 30°, 45° or 60° to other lines may be drawn without showing
construction lines.
At the end of the examination, fasten all your work securely together.
The number of marks is given in brackets [ ] at the end of each question or part question.
All dimensions are in millimetres unless otherwise stated.
This document consists of 9 printed pages and 3 blank pages.
SP (NF/SLM) S81210/3
© UCLES 2005
[Turn over
om
.c
GEOMETRICAL AND MECHANICAL DRAWING
s
er
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS
General Certificate of Education Ordinary Level
2
Section 1 Plane Geometry
Answer not more than three questions from this section.
1
Fig. 1 shows the design logo for a new company.
Draw full size the design logo, showing clearly the method of construction used.
semi ellipse
line tangential
to circumscribing
circle
regular pentagon sides 50
circumscribing circle
Fig. 1
© UCLES 2005
major axis 120
minor axis 50
7040/01/O/N/05
[20]
3
2
Fig. 2 shows the design of a proposed garden layout.
(a) Draw to a scale of 1 : 100 the proposed garden design.
[4]
(b) It is necessary to reduce the area of the garden in the ratio 3 : 5.
Construct geometrically the revised design.
[16]
11
.
2
7.0
5.0
5.0
dimensions in metres
3.3
4.5
3.0
2.5
Ø
0.3
5.5
5.0
Fig. 2
© UCLES 2005
7040/01/O/N/05
[Turn over
4
3
Fig. 3 shows the outline of a mechanism, in which a circular disc rolls without slipping along a
horizontal plane HP. The link OA is rigidly attached to the circular face of the disc. A is pin jointed
to the link AB, which is constrained at B to slide along OX which is parallel to the horizontal plane.
Draw the locus of point R as the disc rolls clockwise from the position shown to the point where
OA has turned through 210°.
[20]
OA = 40
AB = 80
disc Ø60
AR = 40
O
A
X
B
30°
R
H
P
Fig. 3
© UCLES 2005
7040/01/O/N/05
5
Section 2 Solid Geometry
Answer not more than three questions from this section.
4
Fig. 4 shows details of a fume extractor hood drawn to scale.
The hood is open at the top and bottom.
(a) Ignoring the thickness of the material, draw:
(i)
the two given views;
[3]
(ii)
an end elevation.
[2]
(b) Determine the shape for the development of the fume extractor hood, and indicate on the
development the bend lines required for its construction.
[15]
45
20
50
34
55
Fume Extractor Hood
Fig. 4
© UCLES 2005
7040/01/O/N/05
[Turn over
6
5
Fig. 5 shows the elevation of part of a right circular cone. The cone lies with a generator on the
H.P. and parallel to the V.P.
(a) Draw the given elevation.
[3]
(b) Draw a plan view looking in the direction of arrow P.
(c) Name and identify the two curves produced in (b).
[14]
[3]
Ø1
00
P
H.P.
140
Fig. 5
© UCLES 2005
7040/01/O/N/05
7
6
Fig. 6 shows the two views of a casting drawn in third angle projection.
Draw an isometric view of the casting with C the lowest point in the view.
Do not use an isometric scale and do not show any hidden details.
[20]
15
30°
R10
40 AF
25
30
60
Ø
R30
C'
60
30
20
20
R3
20
60
0
C
Fig. 6
© UCLES 2005
7040/01/O/N/05
[Turn over
8
7
Fig. 7 shows two incomplete views of the junction of two offset cylindrical pipes.
(a) Draw the given views.
[3]
(b) Complete the front elevation, showing the curves of intersection.
Include all hidden detail.
[11]
(c) Complete the end elevation.
[6]
Ø
50
15
5
Ø 60
60°
30
60
Fig. 7
© UCLES 2005
7040/01/O/N/05
9
8
Fig. 8 shows the elevation of a truncated regular octagonal prism with sides 40 mm long.
The base of the prism is inclined at 30° to the horizontal plane and is at right angles to the vertical
plane.
Draw full size:
(a) the given view;
[5]
(b) a plan view looking in the direction of arrow P (include all hidden detail);
[9]
(c) the true shape of the cut face looking in the direction of arrow T.
[6]
P
30°
X
Y
Fig. 8
© UCLES 2005
20
50
T
7040/01/O/N/05
10
BLANK PAGE
7040/01/O/N/05
11
BLANK PAGE
7040/01/O/N/05
12
BLANK PAGE
Permission to reproduce items where third-party owned material protected by copyright is included has been sought and cleared where possible. Every
reasonable effort has been made by the publisher (UCLES) to trace copyright holders, but if any items requiring clearance have unwittingly been included, the
publisher will be pleased to make amends at the earliest possible opportunity.
University of Cambridge International Examinations is part of the University of Cambridge Local Examinations Syndicate (UCLES), which is itself a department of
the University of Cambridge.
7040/01/O/N/05