FURNITURE NOTES
FURNITURE NOT IN GENERAL CONTRACT - DETAILS FOR REFERENCE ONLY
SEATING COUNTS
REFER TO FURNITURE SCHEDULE
VARIES
HARDWOOD CAP STAINED
BARRIER FREE
REFER TO FURNITURE SCHEDULE
NEW JERSEY ADMINISTRATIVE CODE
TITLE 5. COMMUNITY AFFAIRS
CHAPTER 23. UNIFORM CONSTRUCTION CODE
SUBCHAPTER 7. BARRIER FREE SUBCODE
N.J.A.C. 5:23-7.11 (2015)
PROVIDE NECESSARY HARDWOOD OR PREMIUM GRADE
PLYWOOD FOR LATERAL BRACING AS REQUIRED.
ALL VERTICAL BRACING AND SUPPORT MEMBERS TO BE
OF PLYWOOD CONSTRUCTION.
5:23-7.11 Requirements applicable to specific nonresidential
Groups and Group R-1
FABRICATOR TO PROVIDE SHOP DRAWINGS FOR APPROVAL
BY ARCHITECT PRIOR TO ANY FABRICATION.
(A) Occupancies of Group A shall be accessible as follows:
1. Where services and facilities are provided in areas that are
not required to be accessible, the same services and
facilities shall be provided in an accessible area and shall be
accessible.
PROVIDE MECHANICAL FASTENERS TO ENSURE
LATERAL STABILITY IN ALL DIRECTIONS.
STAINLESS STEEL SUPPORT LEG
FASTENED TO TABLE TOP &
SECURELY TO THE FLOOR
STAINLESS STEEL SUPPORT LEG
FASTENED TO TABLE TOP &
SECURELY TO THE FLOOR
i. Where fixed or built-in seats and tables are provided, at
least five percent, but not fewer than one, of the seats and
tables shall be accessible. Where more than one accessible
seat and table is provided, they shall be dispersed.
2
TYPICAL SINGLE BOOTH DETAIL
3. Accessible spaces for wheelchairs shall be provided in
each assembly area in accordance with the following table.
TYPICAL DOUBLE BOOTH DETAIL
1 1/2" = 1'-0"
S
Capacity of Seating
4-25
26-50
51-300
301-500 over 500
1 1/2" = 1'-0"
GRAY AREA INDICATES EXISTING
CEILING TO BE REMOVED AND
REINSTALLED AS NEEDED FOR
MECHANICAL WORK
Accessible Seating
1
2
4
6
6 PLUS 1 FOR
EACH100 OVER 500
TE
I
C N
RK
No.
16419
R E D A RC H
I
CONNOR ARCHITECTURE ACCEPTS NO RESPONSIBILITY FOR UNAUTHORIZED
REPRODUCTION OR UNAUTHORIZED USE OF THIS DOCUMENT.
DRAWINGS ARE FOR GENERAL PURPOSES ONLY. NO MEASUREMENTS
SHALL BE SCALED OFF DRAWINGS. ALL MEASUREMENTS SHALL BE VERIFIED
IN FIELD.
ARCHITECT:
CONNOR
ARCHITECTURE
GENERAL NOTES
1.
2.
GRAY AREA INDICATES EXISTING
CEILING TO BE REMOVED AND
REINSTALLED AS NEEDED FOR
MECHANICAL WORK
3.
4.
5.
6.
7.
8.
UPHOLSTERED FURNITURE MUST MEET CAL 117
STANDARDS FOR FLAME SPREAD.
FURNITURE INSTALLER TO WORK WITH CONTRACTOR
AND PROJECT MANAGER TO SET UP DELIVERY AND
INSTALL TO BE WITH IN THE CONSTRUCTION SCHEDULE.
INSTALLER TO REMOVE ALL CARDBOARD, PACKING
MATERIALS, AND OTHER RELATED DEBRIS FROM
PROJECT SITE AND RECYCLE AS MUCH AS IS POSSIBLE.
PROVIDE FURNITURE GLIDES WHICH ARE
MECHANICALLY FASTENED TO CHAIR AND TABLE BASE
BOTTOMS.
FURNITURE GLIDES MUST BE DURABLE AND
REPLACEABLE.
FURNITURE GLIDES MUST OF A MATERIAL THAT CAN BE
USED ON RESILIENT FLOORING.
PROVIDE A LABELED BOX OF 100 ADDITIONAL CHAIR
GLIDES.
PROVIDE A LABELED BOX OF 20 ADDITIONAL TABLE
BASE GLIDES.
1656 Massachusetts Ave.
Lexington, MA 02420
Tel: 781-652-0114
connorarchitecture.com
ENGINEER:
49 Court Street
P.O. Box 1980
Binghamton, NY 13902
Tel: 607-723-9421
mjinc.com
REVISIONS
UP
00
DRAWN BY:
CHECKED BY:
AGK.
AGK.
UP
D
00
00
C ABIN
NA
D AND
A050F
RE01
ET,BKR
B ATTE
R
6
EXISTING TO REMAIN
RESIDENTIAL
DINING
AREA FOR STUDENT ACTIVITIES TABLING
AREA OF ALTERATIONS
FIXED COUNTER STOOLS
953 SF
16
DN
16
70
6
DN
38
78
12
6
16
FLOOR PLAN - FURNITURE
2611 SF
16
RETAIL DINING
RESIDENTIAL
DINING
5655 SF
6
6
1641 SF
16
16
PHASE 1: ALTERATIONS
GRAY AREA INDICATES EXISTING
CEILING TO BE REMOVED AND
REINSTALLED AS NEEDED FOR
MECHANICAL WORK
RCNJ No. 2014-37-01C
RETAIL SERVERY
3976 SF
RAMAPO COLLEGE OF NEW JERSEY
RESIDENTIAL
SERVERY
505 RAMAPO VALLEY RD.
MAHWAH, NJ 07430
UP
AN D BATTER
D 50F
010
NA
KREA
C ABIN ET, BR
3
R EG
BOOTH TO WITHSTAND VERTICAL OR HORIZONTAL OF
250 POUNDS AT ANY POINT ALONG LENGTH
NEW
OF O J
N
ii. In buildings without elevators, an accessible route to a
raised or lowered dining area of less than 3,000 square feet is
not required provided that the raised or lowered dining area
contains less than 25 percent of the total dining area and the
same services are available on the accessible level.
BOOTH TO WITHSTAND VERTICAL OR HORIZONTAL OF
250 POUNDS AT ANY POINT ALONG LENGTH
E
SEY
ER OR
BASE OF BOOTHS & BANQUETTES TO BE
PLYWOOD w/ P-LAM. OUTSIDE CORNERS
TO BE EASED HARDWOOD W/ P-LAM OR
APPROVED DETAIL TO PREVENT
DELAMINATION.
CT
BASE OF BOOTHS & BANQUETTES TO BE
PLYWOOD WITH P-LAM. OUTSIDE
CORNERS TO BE EASED HARDWOOD w/
P-LAM OR APPROVED DETAIL TO
PREVENT DELAMINATION.
2. In dining areas of occupancies of Use Groups A-2 and A-3,
the total floor area allotted for seating and tables shall be
accessible, except as follows:
TE
PROVIDE MECHANICAL
FASTENERS TO ENSURE LATERAL
STABILITY IN ALL DIRECTIONS.
MA
FABRICATOR TO PROVIDE SHOP
DRAWINGS FOR APPROVAL BY
ARCHITECT PRIOR TO ANY
FABRICATION.
ACCESSIBLE: 5
VARIES
REFER TO FURNITURE SCHEDULE
VARIES
DINING SEATS: 265
S TAT
3/31/2015 4:47:21 PM
NJDCA ELECTRONIC SUBMITTAL STAMP:
7
30
16
77
24
1
FURNITURE PLAN
1/8" = 1'-0"
22
FURNITURE NOT IN GENERAL
CONTRACT - FOR REFERENCE ONLY
ISSUED:
3.31.2015
DESCRIPTION:
DCA SUBMISSION
A105
SHEET
