Bluetooth EZ-Extender®
Manual
Revision 1.1, July 2012
Part Number
82-000218-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore Embedded Studio,
EngineerZone, EZ-Board, EZ-Extender, EZ-KIT Lite, and VisualDSP++
are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The Bluetooth EZ-Extender is designed to be used solely in a laboratory
environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The Bluetooth EZ-Extender is currently being processed for certification
that it complies with the essential requirements of the European EMC
directive 89/336/EEC amended by 93/68/EEC and therefore carries the
“CE” mark.
The Bluetooth EZ-Extender contains ESD (electrostatic discharge) sensitive
devices. Electrostatic charges readily accumulate on the human body and
equipment and can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused extender boards in the protective shipping package.
CONTENTS
PREFACE
Product Overview .........................................................................
ix
Purpose of This Manual ................................................................ xi
Intended Audience ........................................................................
xi
Manual Contents ..........................................................................
xi
What’s New in This Manual ......................................................... xii
Technical Support ........................................................................ xii
Supported Products ..................................................................... xiii
Product Information .................................................................... xiv
Analog Devices Web Site ........................................................ xiv
EngineerZone ......................................................................... xiv
Related Documents ....................................................................... xv
USING THE BLUETOOTH EZ-EXTENDER
Package Contents .......................................................................... 1-2
Bluetooth EZ-Extender Default Configuration .............................. 1-2
Bluetooth EZ-Extender Setup ........................................................ 1-3
Flash Memory Interface ................................................................. 1-4
UART Interface ............................................................................ 1-4
Bluetooth EZ-Extender Manual
v
Contents
Bluetooth Module ........................................................................ 1-4
USB Interface ............................................................................... 1-5
Expansion Interface ...................................................................... 1-5
Example Programs ........................................................................ 1-5
BLUETOOTH EZ-EXTENDER HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Configuration Switch ................................................................... 2-3
Jumpers ........................................................................................ 2-5
TWI Flash Address Configuration Jumper (JP1) ...................... 2-6
TWI Flash Write Protect Jumper (JP2) .................................... 2-6
Soft Reset Configuration Jumpers (JP3–4) ............................... 2-6
Bluetooth Module Default Configuration Jumper (JP5) ........... 2-6
UART Receive Data Jumper (JP6) ......................................... 2-6
Power LED ................................................................................... 2-7
Connectors ................................................................................... 2-8
STAMP UART Connector (J1) ............................................... 2-9
Expansion Interface II Connector (J3) ..................................... 2-9
Expansion Interface II Connector (J5) ................................... 2-10
Expansion Interface II Connector (P2) .................................. 2-10
Expansion Interface II Connector (P4) .................................. 2-11
USB Connector (P3) ............................................................. 2-11
vi
Bluetooth EZ-Extender Manual
Contents
BLUETOOTH EZ-EXTENDER BILL OF MATERIALS
BLUETOOTH EZ-EXTENDER SCHEMATIC
INDEX
Bluetooth EZ-Extender Manual
vii
Contents
viii
Bluetooth EZ-Extender Manual
PREFACE
Thank you for purchasing the Bluetooth EZ-Extender®, Analog
Devices, Inc. daughter board to a Blackfin® evaluation system with the
new expansion interface II (such as the ADSP-BF518F EZ-Board®) or the
older STAMP interface (such as the ADSP-BF537 EZ-KIT Lite®).
Blackfin processors are embedded processors that support a Media
Instruction Set Computing (MISC) architecture. This architecture is the
natural merging of RISC, media functions, and digital signal processing
characteristics towards delivering signal processing performance in a
microprocessor-like environment.
The Bluetooth EZ-Extender is designed to be used in conjunction with an
EZ-KIT Lite or an EZ-Board running the open source Linux operating
system (OS). For more information about running Linux OS on a Blackfin processor, go to http://blackfin.uclinux.org/gf/.
Product Overview
The Bluetooth EZ-Extender is a separately sold daughter board that plugs
onto an EZ-KIT Lite supporting the STAMP interface or
an EZ-Board/EZ-Kit Lite supporting the expansion interface II connector. The extender board isolates the low-level configuration and
communication tasks of integrating Bluetooth and radio frequency (RF)
wireless technologies in your Blackfin board designs.
Please visit www.analog.com/EX2-Bluetooth for additional information,
including CCES support.
Bluetooth EZ-Extender Manual
ix
Product Overview
The board extends the capabilities of the Blackfin evaluation system by
providing a connection to the Bluegiga WT12 Bluetooth module.
The board features:
• Bluegiga WT12 Bluetooth module
• Bluetooth radio antenna
• Fully implemented protocol stack
• HCI and iWRAP firmware
• USB interface
• Full speed USB interface for communicating with other
compatible digital devices. The WT12 module acts as
a USB peripheral.
• UART interface
• Standard UART interface for communicating with other
serial devices
• Supports hardware flow control
• Expansion interface
• Allows other EZ-Extenders to be stacked
All of the power necessary to operate the extender is derived from the mating EZ-KIT Lite/EZ-Board. Before using any of the interfaces, follow the
setup procedure in “Bluetooth EZ-Extender Setup” on page 1-3.
x
Bluetooth EZ-Extender Manual
Preface
Purpose of This Manual
The Bluetooth EZ-Extender Manual describes operation and configuration
of the extender board components. A schematic and a bill of materials are
provided for reference.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set.
Programmers who are unfamiliar with Analog Devices processors can use
this manual but should supplement it with other texts that describe your
target architecture. For the locations of these documents, see “Related
Documents”.
Programmers who are unfamiliar with CrossCore Embedded Studio®
(CCES) or VisualDSP++® should refer to the online help and user’s
manuals.
Manual Contents
The manual consists of:
• Chapter 1, “Using the Bluetooth EZ-Extender” on page 1-1
Provides basic board information.
• Chapter 2, “Bluetooth EZ-Extender Hardware Reference” on
page 2-1
Provides information about the hardware aspects of the board.
Bluetooth EZ-Extender Manual
xi
What’s New in This Manual
• Appendix A, “Bluetooth EZ-Extender Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the board.
• Appendix B, “Bluetooth EZ-Extender Schematic” on page B-1
Provides the resources to allow board-level debugging or to use as
a reference guide.
What’s New in This Manual
This is revision 1.1 of the Bluetooth EZ-Extender Manual. The manual has
been updated to include CCES information. In addition, modifications
and corrections based on errata reports against the previous manual revision have been made.
For the latest version of this manual, please refer to the Analog Devices
Web site.
Technical Support
You can reach Analog Devices processors and DSP technical support in
the following ways:
• Post your questions in the processors and DSP support community
at EngineerZone®:
http://ez.analog.com/community/dsp
• Submit your questions to technical support directly at:
http://www.analog.com/support
xii
Bluetooth EZ-Extender Manual
Preface
• E-mail your questions about processors, DSPs, and tools development software from CrossCore Embedded Studio or
VisualDSP++:
Choose Help > Email Support. This creates an e-mail to
processor.tools.support@analog.com and automatically attaches
your CrossCore Embedded Studio or VisualDSP++ version information and license.dat file.
• E-mail your questions about processors and processor applications
to:
processor.support@analog.com or
processor.china@analog.com (Greater China support)
• In the USA only, call 1-800-ANALOGD (1-800-262-5643)
• Contact your Analog Devices sales office or authorized distributor.
Locate one at:
www.analog.com/adi-sales
• Send questions by mail to:
Processors and DSP Technical Support
Analog Devices, Inc.
Three Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Products
The Bluetooth EZ-Extender is designed as an extender board to the
ADSP-BF518F and ADSP-BF526 EZ-Board evaluation systems. The
extender also is compatible with the Blackfin evaluation systems featuring
the STAMP interface, such as the ADSP-BF548 and ADSP-BF527
EZ-KIT Lites.
Bluetooth EZ-Extender Manual
xiii
Product Information
Product Information
Product information can be obtained from the Analog Devices Web site
and the online help.
Analog Devices Web Site
The Analog Devices Web site, www.analog.com, provides information
about a broad range of products—analog integrated circuits, amplifiers,
converters, and digital signal processors.
To access a complete technical library for each processor family, go to
http://www.analog.com/processors/technical_library. The manuals
selection opens a list of current manuals related to the product as well as a
link to the previous revisions of the manuals. When locating your manual
title, note a possible errata check mark next to the title that leads to the
current correction report against the manual.
Also note, MyAnalog is a free feature of the Analog Devices Web site that
allows customization of a Web page to display only the latest information
about products you are interested in. You can choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests, including documentation errata against all manuals. MyAnalog
provides access to books, application notes, data sheets, code examples,
and more.
Visit MyAnalog to sign up. If you are a registered user, just log on. Your
user name is your e-mail address.
EngineerZone
EngineerZone is a technical support forum from Analog Devices. It allows
you direct access to ADI technical support engineers. You can search
FAQs and technical information to get quick answers to your embedded
processing and DSP design questions.
xiv
Bluetooth EZ-Extender Manual
Preface
Use EngineerZone to connect with other DSP developers who face similar
design challenges. You can also use this open forum to share knowledge
and collaborate with the ADI support team and your peers. Visit
http://ez.analog.com to sign up.
Related Documents
For additional information about the product, refer to the following
publications.
Table 1. Related Processor Publications
Title
Description
• ADSP-BF512/ADSP-BF514/ADSP-BF516/
ADSP-BF518(F) Blackfin Embedded Processor
Data Sheet
• ADSP-BF522/ADSP-BF523/ADSP-BF524/
ADSP-BF525/ADSP-BF526/ADSP-BF527
Blackfin Embedded Processor Data Sheet
• ADSP-BF542/ADSP-BF544/ADSP-BF547/
ADSP-BF548/ADSP-BF549 Blackfin
Embedded Processor Data Sheet
• ADSP-BF51x Blackfin Processor Hardware
Reference
• ADSP-BF52x Blackfin Processor Hardware
Reference
• ADSP-BF54x Blackfin Processor Hardware
Reference
General functional description, pinout, and
timing of the processor
Blackfin Processor Programming Reference
Description of all allowed processor assembly
instructions
Bluetooth EZ-Extender Manual
Description of the internal processor architecture and all register functions
xv
Related Documents
xvi
Bluetooth EZ-Extender Manual
1 USING THE BLUETOOTH
EZ-EXTENDER
This chapter describes the Bluetooth EZ-Extender’s package contents,
configuration, installation procedure, and interfaces.
The information is presented in the following order.
• “Package Contents” on page 1-2
Describes the product’s package contents.
• “Bluetooth EZ-Extender Default Configuration” on page 1-2
Describes the board’s default configuration.
• “Bluetooth EZ-Extender Setup” on page 1-3
Provides the board’s setup procedure.
• “Flash Memory Interface” on page 1-4
Describes the on-board flash memory interface.
• “UART Interface” on page 1-4
Describes the on-board UART interface.
• “Bluetooth Module” on page 1-4
Describes the on-board Bluetooth interface.
• “USB Interface” on page 1-5
Describes the on-board USB interface.
Bluetooth EZ-Extender Manual
1-1
Package Contents
• “Expansion Interface” on page 1-5
Describes the board’s expansion interface.
• “Example Programs” on page 1-5
Describes the example programs installed with the board’s
software.
For more information about the mating Blackfin processor, see documents
referred to as “Related Documents”.
Package Contents
Your package contains the Bluetooth EZ-Extender.
If anything is missing, contact the vendor where you purchased your Bluetooth EZ-Extender or contact Analog Devices, Inc.
Bluetooth EZ-Extender Default
Configuration
The Bluetooth EZ-Extender contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body
and equipment and can discharge without detection. Permanent damage
may occur on devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation or loss
of functionality. Store unused extender boards in the protective shipping
package.
1-2
Bluetooth EZ-Extender Manual
Using the Bluetooth EZ-Extender
When removing the Bluetooth EZ-Extender from the package, handle the
board carefully to avoid the discharge of static electricity, which can damage some components (see Figure 1-1).
Figure 1-1. Default EZ-Extender Hardware Setup
Figure 1-1 shows the default jumper and switch settings, connector locations, and LED used in installation. Confirm that your board is in the
default configuration before using the board.
Bluetooth EZ-Extender Setup
It is important to set up all components of the system containing the Bluetooth EZ-Extender and then apply power to the system. Power on your
system after the Bluetooth EZ-Extender has been connected to the
Bluetooth EZ-Extender Manual
1-3
Flash Memory Interface
EZ-Board or EZ-KIT Lite. Do not install or remove the Bluetooth
EZ-Extender when power is applied to the EZ-Board or EZ-KIT Lite.
Flash Memory Interface
The Bluetooth EZ-Extender is equipped with an I2C serial flash memory
chip for data configuration. Flash memory is programmed by the factory.
For more information, refer to “TWI Flash Address Configuration Jumper
(JP1)” on page 2-6 and “TWI Flash Write Protect Jumper (JP2)” on
page 2-6.
UART Interface
The UART interface is used for general communication between the processor and WT12 Bluegiga Bluetooth module. The interface has a max
baud rate of 3.0 Mbaud. Flow control is supported via SW1. Refer to
“Configuration Switch” on page 2-3 for more information.
Bluetooth Module
The Bluegiga WT12 module is a next-generation, class 2, Bluetooth 2.0
plus EDR module. The WT12 is a highly integrated and sophisticated
Bluetooth module, containing all of the necessary elements from Bluetooth radio antenna to a fully implemented protocol stack. Therefore, the
WT12 module provides an ideal solution for developers who want to integrate Bluetooth wireless technology into their design with limited
knowledge of Bluetooth and RF technologies.
By default, the WT12 module is equipped with powerful and easy-to-use
iWRAP firmware. iWRAP enables users to access Bluetooth functionality
with simple ACSII commands delivered to the WT12 module over the
UART interface.
1-4
Bluetooth EZ-Extender Manual
Using the Bluetooth EZ-Extender
Besides the iWRAP firmware, the module has an option for other firmware options. Standard Host Command Interface (HCI) firmware is
supported – an ideal solution for systems where the host system is capable
of running the entire Bluetooth stack and profiles, and the WT12 module
is utilized as the physical radio over the UART interface.
USB Interface
The device operates as a USB peripheral responding to requests from a
master host controller, such as a PC. Both the OHCI and UHCI standards are supported. The set of implemented USB endpoints can behave
as specified in the USB section of the Bluetooth v 2.0 and EDR specification or, alternatively, can appear as a set of endpoints appropriate to USB
audio devices, such as speakers.
Expansion Interface
Expansion interface connectors on top of the Bluetooth EZ-Extender
allow other EZ-Extenders to be mounted on top of the Bluetooth
EZ-Extender. The UART interface is not brought up to the expansion
interface because the interface is used by the WT12 Bluetooth module. All
other signals are passed up to the expansion interface from the mating
EZ-KIT Lite or EZ-Board through the Bluetooth EZ-Extender.
Example Programs
For more information about using the Bluetooth EZ-Extender and running µClinux on a Blackfin processor, go to
http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:bluetooth_ez-extender.
Bluetooth EZ-Extender Manual
1-5
Example Programs
1-6
Bluetooth EZ-Extender Manual
2 BLUETOOTH EZ-EXTENDER
HARDWARE REFERENCE
This chapter describes the hardware design of the Bluetooth EZ-Extender.
The following topics are covered.
• “System Architecture” on page 2-2
Describes the daughter board’s configuration and explains how the
board components interface with the processor and EZ-Board.
• “Configuration Switch” on page 2-3
Shows the location and describes the board’s configuration switch.
• “Jumpers” on page 2-5
Shows the location and describes the board’s jumpers.
• “Power LED” on page 2-7
Shows the location and describes the board’s power LED.
• “Connectors” on page 2-8
Shows the locations, describes, and provides part numbers for the
on-board connectors. In addition, the manufacturer and part number information is provided for the mating parts.
Bluetooth EZ-Extender Manual
2-1
System Architecture
System Architecture
A block diagram of the Bluetooth EZ-Extender is shown in Figure 2-1.
Figure 2-1. Bluetooth EZ-Extender Block Diagram
The block diagram illustrates how the UART, SPORT, and USB ports are
interfaced the Bluetooth module and processor on a mating EZ-KIT
Lite/EZ-Board. The block diagram is a high-level diagram and does not
show the voltage translation circuitry or the clock buffers. The schematic
pages are available in “Bluetooth EZ-Extender Schematic” on page B-1.
The board supports 3.3, 2.5, and 1.8 volt I/O. The on-board voltage
translator automatically translates the motherboard signals to the correct
voltage levels.
2-2
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
The board contains a Bluegiga WT12 class 2, a Bluetooth 2.0, and EDR
module, described in “Bluetooth Module” on page 1-4. The EZ-Extender
is equipped with an I2C serial flash memory chip for data storage and
configuration.
Configuration Switch
This section describes the board’s configuration switch (SW1). The switch
location is shown in Figure 2-2.
Figure 2-2. Configuration Switch Location
Bluetooth EZ-Extender Manual
2-3
Configuration Switch
Positions 7 and 8 of the configuration switch enable or disable UART
flow control. Other switch positions are intended for internal Analog
Devices test purposes only and not supported.
By default, SW1 is all OFF. The switch settings are shown in Table 2-1.
Table 2-1. Configuration Switch (SW1)
2-4
SW1 Position
UART Flow Control Off
UART Flow Control On
SW1.1
OFF
OFF
SW1.2
OFF
OFF
SW1.3
OFF
OFF
SW1.4
OFF
OFF
SW1.5
OFF
OFF
SW1.6
OFF
OFF
SW1.7
OFF
ON
SW1.8
OFF
ON
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
Jumpers
This section describes functionality of the configuration jumpers.
Figure 2-3 shows the jumper locations.
Figure 2-3. Jumper Locations
Bluetooth EZ-Extender Manual
2-5
Jumpers
TWI Flash Address Configuration Jumper (JP1)
The TWI flash address configuration jumper (JP1) controls the base
address of the configuration flash memory. When multiple EZ-Extenders
are stacked on top of each other, it may be necessary to change the JP1 setting to avoid any conflict with the configuration flash memory on another
EZ-Extender. The default is no jumper installed.
TWI Flash Write Protect Jumper (JP2)
The TWI flash write protect jumper (JP2) is not available; the jumper is
intended for internal Analog Devices test purposes only. The default is no
jumper installed.
Soft Reset Configuration Jumpers (JP3–4)
The software reset configuration jumpers (JP3—4) determine which GPIO
signal is used to perform a soft reset of the Bluegiga WT12 Bluetooth
module. The default is no jumpers installed.
Bluetooth Module Default Configuration Jumper
(JP5)
The Bluegiga WT12 Bluetooth module default configuration jumper
(JP5) resets the module’s settings to the default values. This feature
requires software support; refer to the example programs for more information. The default is no jumper installed.
UART Receive Data Jumper (JP6)
The UART receive data jumper (JP6) is not available; the jumper is
intended for internal Analog Devices test purposes only. The default is no
jumper installed.
2-6
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
Power LED
This section describes the power LED (LED1). When LED1 is lit up, it indicates that the board is powered. Figure 2-4 shows the LED location.
Figure 2-4. Power LED Location
Bluetooth EZ-Extender Manual
2-7
Connectors
Connectors
This section describes connector functionality and provides information
about mating connectors. The connector locations are shown in
Figure 2-5. Dashed lines indicate connectors on the bottom side of the
board.
Figure 2-5. Connector Locations
2-8
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
STAMP UART Connector (J1)
The STAMP UART connector (J1) allows the Bluetooth EZ-Extender to
be plugged onto an EZ-KIT Lite development board supporting a
STAMP interface. The J1 connector is located on the bottom side of the
board. For availability and pricing of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-5 or more information.
Part Description
Manufacturer
Part Number
10-position 0.1”, SMT socket
SAMTEC
SSW-105-22-F-D-VS
Mating Connector
10-position 0.1’’, SMT header
SAMTEC TSSH
TSSH-105-01-L-DV-A
Expansion Interface II Connector (J3)
The board-to-board connector (J3) provides signals for the SPI, TWI,
UART, SPORT interfaces and general-purpose I/O (GPIO) signals of the
mating EZ-Board. The connector is located on the bottom side of the
board. For availability and pricing of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-5 for more information.
Part Description
Manufacturer
Part Number
50-position 0.1’’, SMT socket
SAMTEC
SSW-125-22-F-D-VS
Mating Connector
50-position 0.1’’, SMT header
Bluetooth EZ-Extender Manual
SAMTEC
TSSH-125-01-L-DV-A
2-9
Connectors
Expansion Interface II Connector (J5)
The board-to-board connector (J5) provides signals for the PPI, TWI
interfaces and GPIO signals of the mating EZ-Board. The connector is
located on the bottom side of the board. For availability and pricing of the
connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-5 for more information.
Part Description
Manufacturer
Part Number
70-position 0.1’’, SMT socket
SAMTEC
SSW-135-22-F-D-VS
Mating Connector
70-position 0.1’’, SMT header
SAMTEC
TSSH-135-01-L-DV-A
Expansion Interface II Connector (P2)
The board-to-board connector (P2) provides signals for the SPI, TWI,
SPORT interfaces and GPIO signals of the mating EZ-Board. The connector is located on the top side of the board. For availability and pricing
of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-5 for more information.
Part Description
Manufacturer
Part Number
50-position 0.1’’, SMT socket
SAMTEC
TSSH-125-01-L-DV-A
Mating Connector
50-position 0.1’’, SMT header
2-10
SAMTEC
SSW-125-22-F-D-VS
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
Expansion Interface II Connector (P4)
The board-to-board connector (P4) provides signals for the PPI, TWI
interfaces and GPIO signals of the mating EZ-Board. The connector is
located on the top side of the board. For availability and pricing of the
connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-5 for more information.
Part Description
Manufacturer
Part Number
70-position 0.1’’, SMT socket
SAMTEC
TSSH-135-01-L-DV-A
Mating Connector
70-position 0.1’’, SMT header
SAMTEC
SSW-135-22-F-D-VS
Part Description
Manufacturer
Part Number
USB Mini-B connector
MOLEX
0675031010
USB Connector (P3)
Mating Connector
USB Mini-B to USB A cable
Bluetooth EZ-Extender Manual
ASSMANN
AK672M/2-3
2-11
Connectors
2-12
Bluetooth EZ-Extender Manual
A BLUETOOTH EZ-EXTENDER
BILL OF MATERIALS
The bill of materials corresponds to “Bluetooth EZ-Extender Schematic”
on page B-1.
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
1
SN74LVC1G14DB
VR SOT23-5
U4
DIGI-KEY
296-11607-1-ND
2
1
SN74LVC1G08
SOT23-5
U8
TI
SN74LVC1G08DBVR
3
1
WT12 ICS010
U3
BLUEGIGA
WT12-A-AI
4
1
MIC94040 MLF4
U7
MICREL
MIC94040YFL
5
1
M24C02
TSSOP8DW
U2
ST MICRO
M24C02-RDW6TP
6
1
SN74ALVC125
TVSOP14
U9
TI
SN74ALVC125DGVRE4
7
1
ADG3231 SOT23-6
U5
ANALOG
DEVICES
ADG3231BRJZ-REEL
8
1
ADG3308
TSSOP20
U1
ANALOG
DEVICES
ADG3308BRUZ
9
1
DIP8 SWT016
SW1
C&K
TDA08H0SB1
10
1
IDC 3X2
IDC3X2_SMT
JP1
SAMTEC
TSM-103-01-T-DV
11
1
USB_MINI-B 5PIN
CON028
P3
MOLEX
0675031010
12
1
IDC 2X2 IDC2X2
JP4
FCI
68737-404HLF
Bluetooth EZ-Extender Manual
A-1
A-2
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
13
1
IDC 4X2 IDC4X2
JP3
SULLINS
GEC04DAAN
14
1
IDC 25x2
IDC25x2_SMTA
P2
SAMTEC
TSSH-125-01-L-DV-A
15
1
IDC 35x2
IDC35x2_SMTA
P4
SAMTEC
TSSH-135-01-L-DV-A
16
1
IDC 35X2
IDC35x2_SMT_F
J5
SAMTEC
SSW-135-22-F-D-VS
17
1
IDC 25X2
IDC25x2_SMT_F
J3
SAMTEC
SSW-125-22-F-D-VS
18
3
IDC 2X1
IDC2X1_SMT
JP2,JP5-6
SAMTEC
TSM-102-01-T-SV
19
1
IDC 5X2
IDC5x2_SMT_F
J1
SAMTEC
SSW-105-22-F-D-VS
20
12
0.1UF 10V 10%
0402
C1-12
AVX
0402ZD104KAT2A
21
9
10K 1/16W 5%
0402
R1-4,R6,R14-17
VISHAY
CRCW040210K0FKED
22
7
22 1/16W 5% 0402
R11-12,R18-22
PANASONIC
ERJ-2GEJ220X
23
1
1.5K 1/10W 5%
0603
R8
PANASONIC
ERJ-3GEYJ152V
24
1
330 1/10W 5%
0603
R5
VISHAY
CRCW0603330RJNEA
25
1
GREEN LED001
LED1
PANASONIC
LN1361CTR
26
1
47.0K 1/16W 1%
0402
R9
ROHM
MCR01MZPF4702
27
2
10NH 5% 0402
L1-2
PANASONIC
ELJ-QF10NJF
28
2
15K 1/16W 5%
0402
R7,R13
PANASONIC
ERJ-2GEJ153X
29
1
27K 1/16W 5%
0402
R10
PANASONIC
ERJ-2GEJ273X
Bluetooth EZ-Extender Manual
A
B
C
D
1
1
2
2
BLUETOOTH DAUGHTERBOARD
3
3
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
BLUETOOTH EZ-EXTENDER
TITLE
Board No.
C
Date
20 Cotton Road
Rev
A0218-2008
1.1
Sheet
3-27-2009_11:41
D
1
of
4
A
B
C
D
3.3V
L1
10NH
0402
L2
10NH
0402
C1
0.1UF
0402
1
V_SELECT
C2
0.1UF
0402
C3
0.1UF
0402
C4
0.1UF
0402
1
3.3V
SW1
13
5
12
6
11
7
10
8
9
4
5
FS
6
7
UARTCTS
8
UARTRTS
SCLK_TRANS
R18
22
0402
SCLK_BUF
FS_TRANS
R16
10K
0402
FS_BUF
R15
10K
0402
R7
15K
0402
R13
15K
0402
UARTCTS_TRANS
UARTRTS_TRANS
SWT016
DIP8
JP6
1
U3
TP7
2
30
IDC2X1_SMT
3
4
U1
1
VCCA
20
VCCY
20
25
2
A1
3
A2
4
A3
5
A4
6
A5
7
A6
8
A7
9
A8
UARTRX_TRANS
UARTTX
UARTCTS_TRANS
V_SELECT
UARTRTS_TRANS
2
DRPRI_TRANS
DTPRI_TRANS
VCC
UARTRX_TRANS
2
3
1A
1Y
1OE
5
6
2A
2Y
2OE
SCLK_TRANS
9
FS_TRANS
8
3A
10
12
13
3Y
SCLK_BUF
R21
22
0402
3OE
1
RESET
11
4A
11
GND
ADG3308
TSSOP20
DRPRI_BUF
R22
22
0402
4
4Y
U8
UARTRTS
7
UARTCTS
2
3
4
CTS
PIO4
PIO5
D+
PIO6
D-
PIO7
SCLK
7
11
12
13
10
PCMO
SPICS
PCMI
MISO
PCMC
MOSI
RESET
NC
WT12
ICS010
5
2
Y
6
R11
22
0402
10
8
R12
22
0402
9
22
21
23
24
TP3
TP4
2
TP5
TP6
R10
27K
0402
27
R9
47.0K
0402
1
VCC
2
D3
D+
5
GND
6
SHELL
CON028
4
SN74LVC1G14DBVR
SOT23-5
4
GND
ADG3231
SOT23-6
JP5
1
JP3
R8
1.5K
0603
5
P3
IDC2X2
GPIO1
26
PCMS
6
VCCY
3
A
SN74LVC1G08
SOT23-5
JP4
1
RXD
PIO3
U4
4
FS_BUF
RTS
PIO2
EN
U5
1
VCCA
2
4OE
GND
SN74ALVC125
TVSOP14
19
17
UARTRX
R20
22
0402
1
DRPRI_TRANS
FS_TRANS
18
TXD
GND1
GND2
GND3
GND4
GND5
GND6
14
U9
SCLK_TRANS
R19
22
0402
19
Y1
18
Y2
17
Y3
16
Y4
15
Y5
14
Y6
13
Y7
12
Y8
RF
16
4
DTPRI_TRANS
VCC2
14
2
3
3
SCLK
DRPRI_BUF
VCC1
15
2
DTPRI
16
2
1
14
15
28
29
31
1
ON
1
DRPRI
2
1
2
3
4
5
6
7
8
IDC2X1_SMT
GPIO2
GPIO3
GPIO4
R14
10K
0402
R17
10K
0402
IDC4X2
3
3
V_SELECT
3.3V
U2
8
V_SELECT
3.3V
LED1
GREEN
LED001
VCC
JP1
1
2
1
3
4
2
5
6
3
E0
C6
0.1UF
0402
C11
0.1UF
0402
C12
0.1UF
0402
C7
0.1UF
0402
C9
0.1UF
0402
SCL
R4
10K
0402
SDA
E1
E2
IDC3X2_SMT
C8
0.1UF
0402
6
SCL
5
SDA
7
WC
4
GND
C10
0.1UF
0402
JP2
1
2
IDC2X1_SMT
M24C02
TSSOP8DW
R5
330
0603
R3
10K
0402
R1
10K
0402
R2
10K
0402
V_SELECT
ANALOG
DEVICES
4
C5
0.1UF
0402
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
BLUETOOTH EZ-EXTENDER
MODULE
Board No.
C
Date
20 Cotton Road
Rev
A0218-2008
1.1
Sheet
3-27-2009_11:41
D
2
of
4
A
B
C
D
1
1
3.3V
DRPRI
2
SCLK
FS
SDA
UARTRX
UARTCTS
GPIO2
GPIO4
V_SELECT
J3
2
PWR_IN1
GND1
4
PWR_IN2
GND2
6
VDDIO1
GND3
8
VDDIO2
GND4
10
3.3V1
GND5
12
3.3V2
GND6
14
DRPRI
DTPRI
16
DRSEC
DTSEC
18
RSCLK
TSCLK
20
RFS
TFS
22
SPISEL2 SPISEL1
24
SPICLK
SPISEL3
26
SPISS
SPIMOSI
28
TIMER
SPIMISO
30
SDA
SCL
32
UARTRX UARTTX
34
UARTCTSUARTRTS
36
NC
RESET
38
GPIO2
GPIO1
40
GPIO4
GPIO3
42
RSVD2
WAKE
44
RSVD4
RSVD3
46
RSVD6
RSVD5
48
RSVD8
RSVD7
50
RSVD10
RSVD9
IDC25X2_SMT_F
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
P2
1
GND1
PWR_IN1
3
GND2
PWR_IN2
5
GND3
VDDIO1
7
GND4
VDDIO2
9
GND5
3.3V1
11
GND6
3.3V2
13
DTPRI
DRPRI
15
DTSEC
DRSEC
17
TSCLK
RSCLK
19
TFS
RFS
21
SPISEL1 SPISEL2
23
SPISEL3
SPICLK
25
SPIMOSI
SPISS
27
SPIMISO
TIMER
29
SCL
SDA
31
UARTTX UARTRX
33
UARTRTSUARTCTS
35
RESET
NC
37
GPIO1
GPIO2
39
GPIO3
GPIO4
41
WAKE
RSVD1
43
RSVD2
RSVD3
45
RSVD4
RSVD5
47
RSVD6
RSVD7
49
RSVD8
RSVD9
IDC25X2_SMTA
2
4
6
8
10
12
14
16
2
18
20
3.3V
V_SELECT
22
24
26
28
U7
3
1
OUT
4
2
GND
MIC94040
MLF4
IN
30
32
EN
34
36
38
40
J1
2
1
4
3
6
5
8
7
10
9
42
UARTRTS
44
UARTTX
46
UARTCTS
48
UARTRX
50
IDC5X2_SMT_F
GPIO3
R6
10K
0402
GPIO1
RESET
3
3
UARTRTS
UARTTX
SCL
DTPRI
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
BLUETOOTH EZ-EXTENDER
LS CONNECTOR
Board No.
C
Date
20 Cotton Road
Rev
A0218-2008
1.1
Sheet
3-27-2009_11:41
D
3
of
4
A
B
C
D
1
1
3.3V
V_SELECT
J5
2
4
6
8
10
12
14
16
18
20
22
24
2
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
3
68
70
PWR_IN1
GND1
PWR_IN2
GND2
VDDIO1
GND3
VDDIO2
GND4
3.3V1
GND5
3.3V2
GND6
PPI0FS2
PPI0FS1
PPI0CLK
PPI0FS3
PP0D0
PPI0D1
PPI0D2
PPI0D3
PPI0D4
PPI0D5
PPI0D6
PPI0D7
PPI0D8
PPI0D9
PPI0D10
PPI0D11
PPI0D12
PPI0D13
PPI0D14
PPI0D15
PPI0D16
PPI0D17
TIMER1/GPIO
TIMER2/GPIO
TIMER3/GPIO
RESET
PPI1FS2
PPI1FS1
PPI1CLK
PPI1FS3
PP1D0/PPI0D18
PPI1D1/PPI0D19
PPI1D2/PPI0D20
PPI1D3/PPI0D21
PPI1D4/PPI0D22
PPI1D5/PPI0D23
PPI1D6
PPI1D7
PPI1D8
PPI1D9
PPI1D10
PPI1D11
PPI1D12
PPI1D13
PPI1D14
PPI1D15
PPI1D16
PPI1D17
NC
SDA
RSVD2
SCL
RSVD4
RSVD5
RSVD6
RSVD7
RSVD8
IDC35X2_SMT_F
RSVD9
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
P4
1
GND1
3
GND2
5
GND3
7
GND4
9
GND5
11
GND6
13
PPI0FS1
15
PPI0FS3
17
PPI0D1
19
PPI0D3
21
PPI0D5
23
PPI0D7
25
PPI0D9
27
PPI0D11
29
PPI0D13
31
PPI0D15
33
PPI0D17
35
TIMER2/GPIO
37
RESET
39
PPI1FS1
41
PPI1FS3
43
PPI1D1/PPI0D19
45
PPI1D3/PPI0D21
47
PPI1D5/PPI0D23
49
PPI1D7
51
PPI1D9
53
PPI1D11
55
PPI1D13
57
PPI1D15
59
PPI1D17
61
SDA
63
SCL
65
RSVD2
67
RSVD4
69
RSVD6
IDC35X2_SMTA
PWR_IN1
PWR_IN2
VDDIO1
VDDIO2
3.3V1
3.3V2
PPI0FS2
PPI0CLK
PPI0D0
PPI0D2
PPI0D4
PPI0D6
PPI0D8
PPI0D10
PPI0D12
PPI0D14
PPI0D16
TIMER1/GPIO
TIMER3/GPIO
PPI1FS2
PPI1CLK
PP1D0/PPI0D18
PPI1D2/PPI0D20
PPI1D4/PPI0D22
PPI1D6
PPI1D8
PPI1D10
PPI1D12
PPI1D14
PPI1D16
NC
RSVD1
RSVD3
RSVD5
RSVD7
2
4
6
8
10
12
14
16
18
20
22
24
2
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
3
68
70
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
BLUETOOTH EZ-EXTENDER
PPI CONNECTOR
Board No.
C
Date
20 Cotton Road
Rev
A0218-2008
1.1
Sheet
3-27-2009_11:41
D
4
of
4
I
INDEX
A
E
architecture, of this EZ-Extender, 2-2
EDR module, 1-4, 2-3
example programs, 1-5
expansion interface II
overview, 1-5
J3 connector, 2-9
J5 connector, 2-10
P2 connector, 2-10
P4 connector, 2-11
B
bill of materials, A-1
Bluetooth module, 1-4, 2-2
Bluetooth module default config jumper
(JP5), 2-6
board schematic (Bluetooth EZ-Extender),
B-1
C
configuration, of this EZ-Extender, 1-3
configuration switch (SW1), 2-3
connectors
diagram of locations, 2-8
J1 (STAMP UART), 2-9
J3 (expansion interface), 2-9
J5 (expansion interface), 2-10
P2 (expansion interface), 2-10
P3 (USB), 2-11
P4 (expansion interface), 2-11
contents, of this EZ-Extender package, 1-2
F
flash memory interface, 1-4
J
jumpers
diagram of locations, 2-5
JP1 (TWI flash address config), 2-6
JP2 (TWI flash write protect), 2-6
JP3-4 (soft reset config), 2-6
JP5 (Bluetooth module default config),
2-6
JP6 (UART receive data jumper), 2-6
L
D
default configuration, of this EZ-Extender,
1-2
LED1 (power), 2-7
P
power LED (LED1), 2-7
product overview, ix
Bluetooth EZ-Extender Manual
I-1
Index
S
schematic, of Bluetooth EZ-Extender, B-1
setup, of this EZ-Extender, 1-2, 1-3
soft reset config jumpers (JP3-4), 2-6
STAMP UART connector (J1), 2-9
supported products, xiii
switch, SW1 (configuration), 2-3
system architecture, of this EZ-Extender,
2-2
T
technical support, xii
TWI flash address config jumper (JP1), 2-6
TWI flash write protect jumper (JP2), 2-6
U
UART
interface, 1-4, 1-5
receive data jumper (JP6), 2-6
USB
connector (P3), 2-11
interface, 1-5
V
voltage translator, 2-2
W
WT12 Bluetooth module, 1-5
WT12 module, 1-4, 2-3
I-2
Bluetooth EZ-Extender Manual